Question about 2002 Toyota Highlander

Open Question

My garage door opener stop working. I use to use the middle button to open my garage but the light went out and it no longer works. I've been trying to reprogram the other two buttons without success so far. I tried again today and the left side button light went out. That leaves me with one light still working but I still have not been able to reprogram it using the right side and only remaining button that still lights up. Please help.

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
swolfinor
  • 504 Answers

SOURCE: Homelink garage door opener

GOTO HOMELINK.COM

THEY MAKE THE SYSTEM AND HAVE INSTRUCTIONS YOU CAN DOWNLOAD.

ALSO GOOD GUIDE FOR TROUBLE SHOOTING.

HOPE THIS HELPS

Posted on Jun 15, 2010

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The light in my Homelink system does not come on. Therefore it cannot be programmed.


The following are steps to programming a rolling code door opener to the Homelink transmitter in the Touareg.

The instructions in the owner's manual are correct, but after following them, my garage door installer and I discovered a few quirks and fixes for them.

It is important to park the Touareg in front of the garage door. Be careful not to park underneath it. rolleyes.gif

If your remote garage door transmitters are already programmed to your door opener, you need to do the following steps:

1. On the garage door opener itself, there is a learn button. Press and hold down the learn button until the learn indicator light goes out (approx. 6 seconds). (The learn button is near the antenna on your door opener.) By doing this, you have just reset the codes. At this point your remote door transmitters will most likely not work. This is o.k.

2. In the Touareg, press and hold whichever homelink button you want to program until the light above the homelink buttons slowly blinks. Continue to hold the button in and at the same time, hold your remote transmitter underneath the map lights and press the button. Continue to press both buttons until the homelink light rapidly flashes. Let go of both buttons.

3. You now have 30 seconds to press the learn button on your garage door opener. Press it once. The light will start to blink.

4. Go back to the Touareg, press and hold the homelink button you just programmed for 3 seconds until you get a blinking light. Repeat again. This time, it should open or close the door. The homelink button is now programmed.

5. Now that the homelink button is programmed, you now have to re-program your remote transmitters. Take the transmitters with you.

6. On the garage door opener, press the learn button, the light will blink. Now press the button on the remote transmitter. The light should stop blinking. Repeat the step if you have more than one transmitter. You should be all set. The homelink button should work in the Touareg and your remote transmitter(s) should also work.

In summary, the rolling codes in the door opener receiver have to be reset. For some reason, the Touareg has to be programmed FIRST. Then the remote transmitter units. If the remote transmitter units are already programmed, you will most likely not be able to program the homelink in the Touareg for a rolling code door opener.

------------------------------------------------------------------------

Original Launch X-431 DIAGUN III

Mar 14, 2013 | Cars & Trucks

Tip

2010 BMW 528XI Garage Door Opener Homelink Setup


**** >>> This setup I performed with my new 2010 BMW 528XI Garage Door Homelink and Chamberlain Garage Door Opener <<< ****

Chamberlain:
01. Power off or unplug the garage door opener motor power supply (which is mounted on ceiling of the garage) ;;;

02. keep the garage door opener transmitter in your hand (do not press any button at this time) ;;;

03. In your 2010 BMW 528XI Homelink button (which resides under rear view mirror) press the 1st and 3rd homelink button together for about 30-40 seconds (i.e., until the yellow light blinks fast) and when the yellow light next to the homelink button blinks fast release from pressing the (homelink) buttons ;;;

04. now hold the garage door opener transmitter closer (means within 2-4 inches) to the homelink button (either 1st or 2nd or 3rd) whichever you are planning to program to open the garage door ;;;

05. now press the garage door opener transmitter button and chosen homelink button (either 1st or 2nd or 3rd whatever you need) together ;;;

06. the yellow light (next to homelink button) initially may blink slowly but after few seconds (may be 10-20 seconds) will blink fast; once it started blinking fast release from pressing both garage door opener transmitter and homelink button ;;;

07. Now plug or power on the main garage door opener motor (which is mounted on garage ceiling) ;;;

08. On the main garage door opener motor (which is mounted on garage ceiling) press the "LEARN" button (once you press it may have yellow/orange color light; make sure the light is on) ; then within 30 seconds do the next steps #9, #10, #11 very carefully ;;;

09. go to your car and press the homelink button you programmed and hold it for 4 seconds and then release it --> 1st iteration ;;;

10. again hold the same homelink button you programmed and hold it for 4 seconds and then release it --> 2nd iteration ;;;

11. again hold the same homelink button you programmed and hold it for 4 seconds and then release it --> 3rd iteration ** important note; generally three iterations are not necessary; and steps #9, #10, #11 must be performed within 30 seconds ** ;;;

12. during one of the iteration you will hear "CLICK" sound one-time from Garage door motor (which is mounted on ceiling) and if you have light attached with it; it will blink once (** if you hear the CLICK sound and/or light blinks once**) then the particular homelink button is programmed ;;;

13. now press the programmed homelink button; the garage door will open or close (but always it will take 3 or 4 blinks in yellow light or 2-3 seconds before the garage door opens or closes and which is normal) ;;;

** Thats it, your 2010 BMW 528XI Garage Door Opener Homelink setup is complete ** ;;;

You can program rest of the homelink button the same way but following from the steps between #4 and #13 ;;;

Hope this steps will help you to program chamberlain Garage door opener in 2010 BMW 528XI Homelink. ;;;


** possibly the above same steps may work with other BMW 5-series cars homelink too (but I'm not sure) **

on May 29, 2010 | BMW 528 Cars & Trucks

1 Answer

2012 hyundai tucson setting the garage door opener that is located in rear view mirror


Thanks filter4991;
1. Press and hold button on car's rearview mirror
2. Press and hold button on garage door opener's remote control.
3. Light on Rearview mirror will flash rapidly.
4. Release both buttons.
5. Locate learning button on garage door opener (generally this can be found by tracing the antennae to where it is attached to the unit.)
6. Press and release "Learning button"
7. Press and release rearview mirror button repeatedly until garage door opens/closes but it should work the first or second time.

Worked on Genie Intellicode and Hyundai Tuscon

Sep 20, 2012 | Hyundai Tucson Cars & Trucks

1 Answer

2006 GMC Envoy Denali, Universal Garage door opener stopped working. The opener that came with the garage door opener works, but the programmed button in the Envoy suddenly stopped working.


GOTO HOMELINK.COM TO DOWNLOAD INSTRUCTIONS FOR THIS SYSTEM

YOU WILL NEED TO RE PROGRAM THE UNIT WITH YOUR DOOR OPENER.

HOPE THIS HELPS

Jan 24, 2011 | 2006 GMC Envoy Denali

3 Answers

PROGRAM PRIUS GARAGE DOOR HOW DO I PROGRAM THE BUTTONS ON THE PRIUS' REAR VIEW MIRROR TO OPEN THE GARAGE DOOR


There was a minor change for mine to work.. see below..

- you must park your Prius close to the gate opener, leaving it running (obviously not in the way of the gate closing)
- Hold the button the the mirror and then push your garage door remote button and hold until the light on the mirror starts to flasyh fast. THIS programs the button on the mirror, but not the garage opener - yet (this was key for me)
- locate the "learning button" on the opener itself
- press the "learning button" on your gate opener and then get back into the Prius within 30 seconds (more time than it sounds) and press the SAME Homelink button you just programmed above. I don't recall how long I held the pre-programmed button, but the light will flash as I recall.
- Then, when working the garage door, you may need to hold the mirror button for a good second for it to work - but I had tried for months to get mine to work, and finally after reading many posts, the above sequence worked on my 2008 Prius with my Lift Master, Security + rolling codes garage opener.

Just - program the button on the mirror with your remote FIRST.. the garage opener will not work.. then use the Learn button on the garage opener and the SAME BUTTON you just programmed.. and it worked great for me. Not programming the mirror button first will not work. Using only the Learn button will not work. You must program the mirror first with the remote, then use the learn button and the SAME button on the mirror. Hope this helps.

Scott 2008 Prius with Lift Master Security + opener.
-

Oct 30, 2009 | 2007 Toyota Prius

1 Answer

'04 Nissan Altima can't be trained to open garage door.


Hello , you are probably not doing anything wrong. Some garage door openers will not accept some codes. My Toyota Tundra 2005 worked on my garage door , but my 2004 F250 would not. Quinn , Arizona

Jul 16, 2009 | 2004 Nissan Altima

2 Answers

How to program the suv morano garage opener


1. Press and hold the two outside garage opener buttons located on rear view mirror until the red LED light blinks (could be 20 sec.)
2. Press and hold the middle button on the rear view mirror while holding a garage door remote 1-3 inches away from the mirror and pressing the remote button. Do this until the blinking LED gets noticeably faster.
3. Once programmed - use the garage door opener on the mirror thru 3 cycles or more to verify.

Jun 26, 2009 | 2005 Nissan Murano

1 Answer

I have homelink garage door opener in my 2003 Lexus RX300. The light no longer flashes when I push the button to open the garage door and the door does not open. Is homelink wired or battery...


I don't think it's a problem with the homelink opener in your RX300. Try resynching it again with the garage door opener. Mine failed to work once and I just resynched and it's been OK for months now.

Sep 14, 2008 | 2002 Lexus RX 300

4 Answers

Program garage door opener


You must first erase what's in the memory.
1.) Simultaneously press both buttons 1 and 3 on the Audi's built-in remote. Hold them until the indicator light flashes (20 seconds or longer).
2.) Now hold your garage door remote close to the Audi remote.
3.) Simultaneously press and hold both your garage door remote button and the button you would like programmed. The indicator light will first flash slowly then rapidly.
4.) You may release both buttons once the light flashes rapidly.

Jul 01, 2008 | 2000 Audi A6

1 Answer

Programming the garage door opener


Homelink Garage Door Opener Programming Procedure:

The procedure described below was successfully applied to a 2005 Jaguar S-Type.

To begin with, several attempts were made using the programming instructions contained in my Jaguars owners manual. Though the procedure described in the owners manual was straight-forward and understandable, I was unsuccessful in getting the vehicles remote to make my garage door opener function. The particular garage door openers I have are both made by Genie. Both openers utilize the Rolling Code feature.

To begin with, be sure to clear previous codes on your Jaguars garage door opener by first turning (rotating) the ignition key to the I position (first notch). Next, simultaneously hold button 1 (left most button) and button 3 (right most button) down until the middle buttons red light changes from continuous on to a rapid flash. This process takes approximately 20-25 seconds. What follows is a two part process. In the first part, get your Genie portable remote and hold it near (approximately 3 inches away from) your Jaguars garage door opener console buttons. Choose which button on your Jaguars remote you wish to dedicate to your Genie door opener and simultaneously press and hold your Genie opener button and your Jaguars opener button. The red light on your Jaguars center button (button #2) will light up and within 1-2 seconds will begin to flash rapidly. You have just completed part 1 of the two part process.

Part two: Now it is time to utilize the Learn function on your Genie garage door opener. Press the Learn button on your Genie garage door opener. The red LED adjacent to the Learn button will begin to flash. You now have 30 seconds in which to program your Jaguars opener button. Using the same button you just used in the part 1 procedure, press and hold the same button for several seconds. As before, your Jaguars red light in the middle button will light up and within 1-2 seconds, it will flash rapidly. Release the button you are programming. Now, here is the key piece of information! Once again, press and hold that same button. Once again, the center buttons red light will flash rapidly. Release your newly programmed button. This procedure proved successful in my application. Here is what has just happened. The first time you pressed your Jaguars remote button tells the Genie opener that it exists and that it is a viable candidate for making your life easier (opening the damn door). The second time you press your Jaguars remote button confirms to the Genies rolling code that your Jaguars signal is legitimate and is to be trusted from then on.

Jun 06, 2008 | 2003 Jaguar XJ-Series

Not finding what you are looking for?
2002 Toyota Highlander Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...