Question about 2004 Dodge Neon

1 Answer

When I turn the key all of my gauges move and my alarms go off but the starter does not turn over. How can I get a wiring diagram to help me locate where the power stops reaching the starter?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Champion:

    An expert who has answered 200 questions.

  • Contributor
  • 264 Answers

HI the factory theft system has armed it self. If you havea second set of keys try them a key can go bad and not signal the car to start. If the other keys fail you will be visiting your freindly Chrysler dealer.. Good luck i hope your other set of keys works.

Posted on Aug 26, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Gas gauge problem


check all wiring around starter to see if you pinched 1 or 1 is grounding against starter.
can not add more because you not state make an model

Aug 14, 2015 | Cars & Trucks

2 Answers

1997 ford expedition the fuse for the gauge blowing when I turn on the key switch what cause that


Impossible to tell without knowing what fuse number is blowing, along with some basic electrical troubleshooting.
Common suspects include:
altered factory stereo
Aftermarket alarm system
chafed wiring
defective instrument lamp
defective instrument panel

Dec 06, 2014 | 1997 Ford Expedition

1 Answer

My 2008 Saturn Vue won't crank or start!? We have tried everything to get the Saturn started but nothing working. It's not the starter or the battery. We have lights and everything works just won't crank...


If you have a voltmeter, Connect one end to the hot terminal on your starter. (Making sure that you don't get any body part or anything stuck in any moving parts in your engine compartment!) Turn the key and look at the meter. If it goes up to 12 V or higher, that means that power is getting to the starter, and the problem is either the starter or a bad ground. If the voltage stays at zero, the problem is before the starter and could be your alarm, a relay, a fuse, etc. It would help you to have the wiring diagram for your car.

May 25, 2014 | Cars & Trucks

1 Answer

I have a 1982 dodge ram w150 318 4 speed when i turn the key i lose everything let me start from the beginning my truck started up then died then when I went to restart I heard a thunk then nothing last...


What happens when you turn the key to on? Do the warning lights and gauges come on? Turning the key to start, do the lights and gauges stay on? Just nothing at the starter?

Or does power just shut off when you turn the key to start, everything goes out, no warning lights or gauges? Then check cables, battery terminals, grounds for clean tight connections. There is a problem between the battery and the ignition switch.

If the switch still receives and sends power out (to the dash, for one) but start circuit is not working (from battery to ignition switch to clutch switch to starter relay to starter solenoid to starter to ground-and back to battery), then here's where we at: with key off, use a small screwdriver and short the big cable at starter to the starter solenoid small wire connection, or use a small jumper wire to do the same-battery cable at starter to the small wire connection on the starter solenoid. Starter motor should spin and crank engine. Does it? If so, start checking the start wire out of ignition switch for power when key is held in start. If you have a clutch switch, check for power in with key in start. Should have battery voltage to the clutch switch with key held in start. Keep checking the start wire along the start circuit. Not sure how the start relay is wired into the circuit, would have to see a diagram, but if you pull the relay out and use a test light or multi meter, could check for power on the terminals where relay plugs in. Key off, should have one terminal that is hot. With key held in start, at least one other terminal should also be hot. This would be the start wire out of ignition switch sending a signal to the relay.
Good luck, hope you find it. Sorry I don't have a wiring diagram to help you more.

Aug 30, 2013 | 2000 Dodge Caravan

1 Answer

P heh vw polo just cut out and will not start again. Could it be the fuel pump relay.


The locks are tied into the alarm control unit. The control unit has a starter lock out. If the alarm system did not see a door open using a key, it does not deactivate the starter lock out.

Normally if you have a bad door contact switch you can open another door or trunk to test this theory out. Since you can not do this, we will need to take a few steps. You need to locate the alarm control unit, it is a small black box located just to the left side of the steering colum. You will see a large conector of wires that go to it. Locate the two large red wires, one will be red and one will be red with a black stripe.

Probe both wires, and while turning the key to the crank position you should have power going through both of these wires. If not let me know. If you do have power going through both of the wires, then the problem is not the alarm unit.

Hope this helps.

Feb 21, 2012 | 1995 Volkswagen Polo 1.4

1 Answer

I bought a 1996 Subaru Impreza L 4dr 5speed AWD that runs and starts fine but when I was installing fog lights i noticed that there appears to be an alarm hooked up (it says "code alarm elite DM...


Battery Constant 12v+ Positive Wire (+): Black/Yellow
Battery Constant 12v+ Positive Wire Location: Ignition Switch Harness

Starter Positive Wire (+): Blue/Red
Starter Positive Wire Location: Ignition Switch Harness

Ignition Positive Wire (+): Red
Ignition Positive Wire Location: Ignition Switch Harness

Accessory Positive Wire (+): Red/Yellow
Accessory Positive Wire Location: Ignition Switch Harness

Parking Light Positive Wire (+): Red
Parking Light Positive Wire Location: Low In Drivers Kick Panel

Power Door Lock Negative Wire (-): Add Actuator. This vehicle uses a central door locking system. When connecting a keyless entry, you will need to add a door lock actuator and some units will also require (2) extra relays.
Power Door Lock Negative Wire Location: To Drivers Door Only

Power Door Unlock Negative Wire (-): Add Actuator. This vehicle uses a central door locking system. When connecting a keyless entry, you will need to add a door lock actuator and some units will also require (2) extra relays.
Power Door Unlock Negative Wire Location: To Drivers Door Only

Door Trigger Negative Wire (-): Red/White
Door Trigger Negative Wire Location: In Black Plug, Above Hood Release

Domelight Supervision Wire: Use Door Trigger, Requires Relay
Domelight Supervision Wire Location: N/A

Horn Negative Wire (-): Red/Green
Horn Negative Wire Location: At Steering Column Harness

Tachometer Wire Negative Wire (-): Black/Blue
Tachometer Wire Negative Wire Location: At ECM, Under Drivers Side Dash

Brake Light Positive Wire (+): White/Black
Brake Light Positive Wire Location: At Switch Above Brake Pedal

CODE ALARM SYSTEM

Used on:
Impreza 1996-2001
Legacy 1995-1999
Forester 1998-2000

codealarmremote2.jpgBattery GP-23A

Lock: Left button will lock all doors. Double chirp indicates locked.
Unlock: Right button will unlock driver's door only. Hold unlock button app 6 seconds, it will unlock all doors including rear gate. Single chirp indicated unlock.
If the car chirps or lights flash 4x the alarm was triggered.
Panic. Press both buttons to activate emergency honk and flashing lights.
Valet mode: With optional alarm onlyPress the red alarm button on the left of the steering wheel. The light will quickly double flash. To re-set back to normal mode, press the red alarm light button again

Battery failed and lights flashing?
Parking lights will flash when the vehicle's battery is disconnected and reconnected.
To stop lights from flashing, either:
Press remote transmitter "UNLOCK" button once OR turn the ignition switch to the "ON" position and press programming button for one second (see below).
The vehicle interior (courtesy) light and door open warning light (DOOR AJAR indicator) will then illuminate for 60 seconds when the ignition is turned off, or until the doors are locked with the remote transmitter. Yes, the dashboard instrument panel lights will flash when the parking lights flash.

Programming or Overriding the Alarm when you have lost the remote
Open driver's door.
Turn ignition key to 'On'
Press and *hold programming button* in (see diagram, button under dashboard)
After 15 seconds the the door locks will cycle 3 times. Do not release Programming button.
Press lock (left) button the remotes to be programmed. The door locks will cycle one time. Exit programming mode by releasing Programming button under dashboard and turning key to off.


codealarmremote1.jpgCode Alarm Programming Button is under dashboard on the kick panel by the driver's left knee, left of the steering column. If you can't find it, it might still be tucked up in the wiring harness higher up in that same general area. The botton is recessed in a plastic ring (see diagram).
This button must be pressed while programming remotes or if the battery was disconnected and the lights are flashing.

Jan 05, 2011 | Subaru Impreza Cars & Trucks

2 Answers

My 1993 Toyota Tercel does not start when key is turned. New battery, all fuses checked and fine. When the doors get opened, hazard lights start blinking for 15 blinks, then pause, then 15 blinks. This...


This sounds like a starter disable feature of a car alarm. Somewhere under the dash you are going to find a box with the start wires running to it. The start wire is black with a white stripe and is thick, about a 12 gauge wire. It will come from the ignition switch and run into a relay or box. It could be installed anywhere as it is aftermarket. Once you find it, you can reconnect both ends of the starter wire and you can start it with the key. I would disconnect the power to the alarm or your lights are going to flash at random. The factory alarm (just in case it is the issue, but that isn't likely) is located behind the radio and ashtray.

Dec 14, 2010 | Toyota Tercel Cars & Trucks

3 Answers

I need to disable my alarm on a 1997 bmw 528i.


Now im not sure since the manual says your model has the same alarm system as the 328i and on the 328i you can remove the module to disable by doing the following. you can unplug the control module. It is located under the glove box. Climb under the dash on the passenger side and remove a few screws on the trim panel under the glove box. Theres a black control module with a green connector. There should be a lock tab on the connector. press the lock tab and pull out the connector. The alarm should now be disabled. But if it has the special transponder key this may not work.
But if the only reason you want to disable it is because of the motion sensor setting of the alarm for no reason there is a solution for this. To disable the motion sensor, hit the lock button to arm, then hit lock button again within four seconds to disable motion sensor. Red light on rearview mirror should flash four times, then pause, then start flashing on regular intervals. this is most likely the reason if your having the issue where the alarm goes off every 20 minutes.
If you want to completely remove it below is a wiring diagram taken from the manual for you alarm system.
this is from the manual its the alarm wiring diagram.
Battery Constant 12v Positive Wire ( ): Red/White or RedBattery Constant 12v Positive Wire Location: Ignition Switch Harness
Starter Positive Wire ( ): Black/Yellow or Black
Starter Positive Wire Location: Ignition Switch Harness
Ignition Positive Wire ( ): Green
Ignition Positive Wire Location: Ignition Switch Harness
Second Ignition Positive Wire ( ): Purple/White or Purple
Second Ignition Positive Wire Location: Ignition Switch Harness
Parking Light Positive Wire ( ): Gray/Purple and Gray/Yellow. Use Both Wires. This vehicle has a dual parking light system that will require 2 extra relays.
Parking Light Positive Wire Location: At Headlight Switch
Power Door Lock Positive Wire ( ): White/Red
Power Door Lock Positive Wire Location: At Factory Alarm Plug. The alarm plug is a black 12 pin plug located just behind the glove box.
Power Door Unlock Positive Wire ( ): Blue/Red
Power Door Unlock Positive Wire Location: At Factory Alarm Plug. The alarm plug is a black 12 pin plug located just behind the glove box.
Door Trigger Negative Wire (-): Brown/Gray
Door Trigger Negative Wire Location: At Factory Alarm Plug. The alarm plug is a black 12 pin plug located just behind the glove box.
Domelight Supervision Wire: Turns On With Unlock
Domelight Supervision Wire Location: N/A
Horn Negative Wire (-): Brown/Red or Brown/Yellow
Horn Negative Wire Location: At Steering Column Harness
Tachometer Wire Negative Wire (-): Black
Tachometer Wire Negative Wire Location: At Instrument Cluster
Brake Light Positive Wire ( ): Blue/Red or Green/Red
Brake Light Positive Wire Location: At Switch Above Brake Pedal
Factory Alarm Disarm Wire (-): Disarms With Factory Remote Only. Factory Alarm Disarm Wire Location: N/A
Factory Anti-Theft System: Transponder Anti-Theft System, Requires Bypass And Extra Ignition Key. The 1997 model year vehicle may require a bypass module and an extra ignition key, if vehicle is equipped with a special key from BMW.
Factory Anti-Theft System Location: Transponder At Ignition Switch Tumbler
if you require further assistance please let me know and i will help assist you from there. Thanks, Midwest-Tek

Aug 27, 2010 | 1997 BMW 328

1 Answer

79 chevy k10 starter problems


Fusible Links

The engine compartment wiring harness has several fusible links. The same size wire with a special hypalon insulation must be used when replacing a fusible link.
The links are located in the following areas:
  1. A molded splice at the starter solenoid Bat terminal, a 14 gauge red wire.
  2. A 16 gauge red fusible link at the junction block to protect the unfused wiring of 12 gauge or larger wire. This link stops at the bulkhead connector.
  3. The alternator warning light and field circuitry is protected by a 20 gauge red wire fusible link used in the battery feed to voltage regular #3 terminal. The link is installed as a molded splice in the circuit at the junction block.
  4. The ammeter circuit is protected by two 20 gauge fusible links installed as molded splices in the circuit at the junction block and battery to starter circuit.
Other things it MIGHT be are the ignition switch, located on top of the steering column:

0a5a9c9.gif
The other thing it MIGHT be is a faulty ignition cylinder (where your key goes into to start the K10).

Check the wire harness on the steering column also.

Oct 28, 2009 | 1983 Chevrolet C1500

1 Answer

HORN DIAGRAM FOR A DODGE RAM 1500 (CONNECTIONS)


Battery Constant 12v+ Positive Wire (+): Black/Orange And Red/White
Battery Constant 12v+ Positive Wire Location: Ignition Switch Harness
Starter Positive Wire (+): Yellow
Starter Positive Wire Location: Ignition Switch Harness
Ignition Positive Wire (+): Blue (16 Gauge)
Ignition Positive Wire Location: Ignition Switch Harness
Second Ignition Positive Wire (+): Yellow/Red
Second Ignition Positive Wire Location: Ignition Switch Harness
Accessory Positive Wire (+): Blue (10 Gauge)
Accessory Positive Wire Location: Ignition Switch Harness
Second Accessory Positive Wire (+): Orange
Second Accessory Positive Wire Location: Ignition Switch Harness
Parking Light Positive Wire (+): Black/Yellow
Parking Light Positive Wire Location: At Headlight Switch
Power Door Lock Positive Wire (+): Orange/Violet
Power Door Lock Positive Wire Location: In Drivers Kick Panel, White 6-Pin
Power Door Unlock Positive Wire (+): Pink/Violet
Power Door Unlock Positive Wire Location: In Drivers Kick Panel, White 12-Pin
Door Trigger Negative Wire (-): Yellow
Door Trigger Negative Wire Location: At Headlight Switch
Domelight Supervision Wire: Use Door Trigger (Requires Relay)
Domelight Supervision Wire Location: N/A
Horn Negative Wire (-): Black/Red
Horn Negative Wire Location: At Steering Column Harness
Tachometer Wire Negative Wire (-): Gray
Tachometer Wire Negative Wire Location: At PCM, Connector 1, Pin A7. The PCM (powertrain control module) is located on the firewall next to the wiper motor.
Brake Light Positive Wire (+): White/Tan
Brake Light Positive Wire Location: At Switch Above Brake Pedal
Factory Alarm Disarm Wire (-): Black/Orange (To disarm requires a (-) negative through a 1565 ohm resistor and an extra relay to connect.)
Factory Alarm Disarm Wire Location: In Drivers Kick Panel, White 12 Pin Plug
Factory Anti-Theft System: N/A
Factory Anti-Theft System Location: N/A

Aug 22, 2009 | 1998 Dodge Ram 3500 2WD

Not finding what you are looking for?
2004 Dodge Neon Logo

Related Topics:

153 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...