Question about 1991 Ford Explorer

1 Answer

Stalls when placed in drive - 1991 Ford Explorer

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

Have you tried to check your mass airflow sensor? or come carb or injector cleaner? that could be the simplest and cheapest to fix. But first,Do the RPM's increase when you turn on the AC at idle? You idle is controled by the AIC (Air Idle Control). This is that part that is bolted to the drivers side of your intake . The AIC's job is to give you no-touch starting, keep the idle up, and increase idle when you turn on the AC. If it isn't working it will start/stall even in park when its cold. That is a very common problem to have. The AIC usually runs about a hundred bucks. so its best to hope its just the sensor of your carb/injectors need cleaned.

Posted on Aug 26, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2004 c5 corvette stalls when placed in drive gear.


The dealer should be able to plug it in to a computer to figure it out.

Dec 08, 2014 | 2004 Chevrolet Corvette C5

1 Answer

Why doe;s my 97 Ford expedition stall only when turning into a parking place or my drive way?


there is a sensor that will increase engine revs when turning at slow speed , i expect this is the issue, to check get the OBD codes read to confirm

Oct 23, 2014 | Ford Expedition Cars & Trucks

1 Answer

2000 tundra runs in park but stalls in drive


ok,
cel light on running?
scan it.
no engine power. (low fuel pressure, filthy maf? )

Feb 15, 2014 | Toyota Tundra Cars & Trucks

1 Answer

2004 pontiac gand prix while driving it stall and never done it before i will place car in park again and start it works what is wrong with my car


run fault codes to find which sensor has become faulty and put the engine in limp mode.. Check oil and coolant levels

Jan 04, 2014 | 2004 Pontiac Grand Prix

1 Answer

Where does the rubber seal go on throttle position sensor and will this cause the engine to stall if not installed? I CHANGED this sensor but it still stalls when driving after it warms up.This is on a 97...


It shouldn't make it stall, but needs to be in place. The most likely cause of a stall is a vacuum leak, or faulty idle control solenoid located next to the throttle position sensor.

Jan 17, 2010 | 1997 Pontiac Trans Sport

1 Answer

1990 Pontiac 6000 2.5 after driving, car stalls when put in gear.


You need to replace the TCC solenoid under the side cover pan of the transmission. You can also unplug the wires that go to the transmission in the front. After that it will not go into overdrive but it will stay running at stop lights untill you have it repaired.

Sep 28, 2009 | 1990 Pontiac 6000

1 Answer

93 voyageur keeps stalling?


The owner should locate the fuel pump first before servicing . prepare the equipment to use in servicing the the fuel pump.The owner of the car should adjust the the Idle. Start the car and check the fuel pump Idle and adjust until the car can drive when it is place into gear.the problem in the car is in the Idle, it means that there is low fuel passing to the fuel pump, that is why the car when it drives or the strength of the car is low when placed into drive. there fore adjusting the Idle until the car will drive when placed into gear is the solution.If the owner don't have time to do it then the owner of the car should go to a car mechanic to do the task or job.

Sep 27, 2009 | 1993 Plymouth Voyager

1 Answer

Was driving truck and stopped at a light.truck started to stall so i put into neutral. started driving again and truck started to stall and backfire as i continued to kepp it running. truck stalled and...


i would check the dist.cap and wires.this seems to be a place to start.check all vacum lines.would also check fuel pump pressure.you need to determine if its fuel or elect.may also consider cam sensor.

Sep 25, 2009 | 1994 GMC Sierra

1 Answer

Stalls just after idling for more than 3 minutes


I had the same problem. you have to either keep replacing the filter until the line has cleaned out or blow the filter out with an air hose. Tedious but cheap.

Aug 01, 2009 | 1993 Dodge Caravan

Not finding what you are looking for?
1991 Ford Explorer Logo

Related Topics:

143 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...