Question about Suzuki Esteem

Open Question

I need crankshaft torque specs for a suzuki esteem 1.6L

Posted by on

  • wmstalk Aug 26, 2010

    HI , what year Suzuki and what spec? Crankshaft bearing caps?

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 25 Answers

SOURCE: 87 samurai bolt torque specs for engine

The haynes book is not recommended since there are numerous mistakes and they still will not update. One of the biggest is the firing order.

The factory service manual is the only way to go.

Head bolts - 46 - 50.5 lbs (there is an order sequence for the bolts)

Intake & exhuast manifolds- 13.5 - 20 lbs

Flywheel - 41.5 - 47 lbs

Clutch cover - 13.5 - 20 lbs

Posted on Mar 17, 2009

  • 599 Answers

SOURCE: 2004 Chevrolet HD 6L VORTEC: Replaced the knock

the torque spec is 15 ft lbs. hope this helps. Thanks Ray

Posted on Nov 12, 2009

Testimonial: "Thanks a million Ray, u saved ALOT of aggravation of WAITING until working hours to find out this info... Thanks again... Shauna"

  • 1 Answer

SOURCE: how do i changing alternator suzuki esteem 2001

take it to a mechanic trust me, i had to replace mine after 6 days of trying to figure out how to remove the bottom bolt i took it to a shop if you need to know more email me KRAGAR33@AOL.COM

Posted on Dec 05, 2009

  • 701 Answers

SOURCE: need the crankshaft main bearing torque specs and

Hello tlittle3: My name is Roger and I will help you.See the attached image. Be sure to follow steps as it is very inportant. You will notice that you need to index some of the bolts. That is merely turning the bolt a specified degree. The crankshaft tie bolts are the bolts that are in the side of the block. install horizontal. Shold you need further help please just ask. Please rate the answer you received. Thank You for using Fix Ya. Rogera32a1ae.jpg

Posted on Apr 26, 2010

Testimonial: "thanks that what i needed"

alicantecoli
  • 22156 Answers

SOURCE: need torque specs on flywheel to crankshaft for

go by the size of the bolt shank the thicker the bolt the more the torque ,also use some form of locktite on them or contact adhesive will do ,if a 15mm head then about 65lb if 17mm then 75lb and 19 mm 85lb ,and dont forget the sticky stuff

Posted on Sep 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where location crank sensor suzuki esteem 2000


On the Esteem 1.6L: the Crankshaft Position Sensor is located on the right side (passenger side) of the engine Oil Pan.

For the Esteem 2.0L: the CKP is located behind the engine Flywheel in the back of the engine block. It is necessary to remove the transmission to service the sensor.

Dec 27, 2010 | 2000 Suzuki Esteem

1 Answer

2000 Suzuki Esteem (1.8) Fuel System


No SYMPTOMS stated, (sadly)
the J18 engines, twin cam, chain drive cam, nice motor.
an under stroked, J20. it is.. and share most parts.

alldata.com covers it.... and all cars... mostly.
for sure esteems (used books real off Ebay, if lucky, do a watch on ebay)?
and for sure Suzuki, the FSM is $4 to read. and posted 100 time here. (more ) this the real deal, (McCoy)
https://suzukipitstopplus.com/Products/1182-2000-esteem-service-manual.aspx

the filter, and pump , no need to replace pump unless
it has 12vdc to IT CRANKING< and filter is new. AND, pressure is out of spec. (see spec, below)
a gauge is $20 and way more easy to use than a bath in gasoline
for sure.and a $10 voltmeter from walfart.

now the Esteem secret (just in CASE)
"Remove rear seat cushion, rear right seat back, right side sill scuff, right front partition trim and right rear door opening trim."
bingo, a secret access port.

now the spec.
31-37 ?idle PSI
this is the fuel pressure at the rail, at idle.
cranking is 6 PSI more
driving up hill, wide open throttle, pressure rises to 3- 6psi more that idle. (near)
if pressure is low, check for 12vdc to pump, first.
then make sure the FPR works.
they can stick open closed or jam. and it must work right. or fueling will be ALL wrong. (cars this old FPR love to fail)
this engine ECU has program revision (flash) that causes
pump to not run key on, (read TSBs on same at suzuki...)

so, crank it and check pressure cranking if not starting?
or if it does start (you never said) then check at idle
and WOT. the PSI ( then gun throttle see pressure jump way higher) if all this pans out, forget pump, and FPR.

did you scan the PCM yet, that be like first..
all scan tools (real) work on 2000 cars.... all do.

Dec 14, 2009 | 2000 Suzuki Esteem

1 Answer

Need torque specs for 1.3 liter motor,connecting rod bearing and main bearings.


MAIN BEARING TORQUE IS 36 -41 FT LBS. ROD BEARING TORQUE IS 24 -26 FT LBS

Jul 07, 2009 | 1995 Suzuki Esteem

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...