Question about Ford F-100

1 Answer

What are the torque specs for the valve cover on a 4.9L 300 straight 6 motor? Thanks

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 220 Answers

Hope this helps

7 Ft-Lbs 84 In-Lbs 9.49 N-m Connects: Valve Cover To Cylinder Head Years: All

Posted on Aug 26, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2004 Bmw x5 valve cover torque specs


valve cover gasket torque spec? - Bimmerforums

www.bimmerforums.com/.../showthread.php?...valve-cover...torque-spe...
Dec 7, 2012 - Remember the little rubber grommets around the cover bolts? ... Location: alabama; Posts: 5,537; My Cars: 2002 bmw 325 ... Torque spec for the M52 valve cover bolts is 89 inch-pounds / 7.4 ... 1976 - 1989 (E24) · 2004+ (E63, E64) ... 2012+ X1 (E84) · 2003+ X3 (E83,F25) · 1999+ X5, X6 (E53, E70, E71). Valve Cover Bolt Torque Specs
Oct 25, 2014
Valve cover screw torque specs?
Nov 9, 2012
leaking valve cover gasket
Dec 29, 2011
How specific for torque specs?
Dec 27, 2011
More results from www.bimmerforums.com

Nov 06, 2015 | Cars & Trucks

1 Answer

What is the torque specs for 2002 Sonata 2.4 dohc valve cover bolts?


Valve cover bolts are in most cases reusable unless rounded off or striped. If the bolts are m6 89in/lbs should be good m8 105 in/lbs.

Feb 18, 2013 | Hyundai Motor 2004 Sonata

1 Answer

Need valve cover torque specs for 2002 Kia Spectra


The torque specs for a Kia 1.8 valve cover is 43-78 inch pounds...... Basically just snug....

Nov 13, 2011 | Cars & Trucks

1 Answer

I need the torque specs for my valve covers on my 1990 bronco 2 v-6


No torque specs. Don't use sealer, that can cause the gasket to slip. Put cover in place, start all bolts, loosely snug all, hand tighten from bottom two, top two, bottom ends, top ends. Warm up motor and re-tighten (good hand snug) do not over tighten.

Oct 19, 2010 | 1990 Ford Bronco

1 Answer

Need the torque specs for the straight six 300 ford motor


Here is the spec for 1977 through 1984 on the Ford 300 or so called now the 4.9 engine:
Cylinder head bolts: 70-75 lbs. The sequence is driver's side starting on bolt one (fifth bolt in line of bolts or center of line of bolts) and going straight across to bolt 2 on passengers' side and then to the side of bolt 2 is bolt 3 and back across to bolt four to the right of bolt 1. This is done in a zig -zag pattern until all bolts are torqued to recommended torque.

segon s version
rear front
13 9 5 1 4 8 12 torque specs are in three steps
11 7 3 2 6 10 14 1) 55lbs 2) 65lbs 3) 85 lbs
all info from the book

Sep 25, 2010 | 1981 Ford F 100

1 Answer

What is the torque setting for the valve covers on a 327 chevy engine? Its on a 1967 Chevy Impala but not original motor. Thanks!


The torque spec on the valve cover bolts is 3 ft pounds or 36 inch pounds.
This spec is good for all Chevy small blocks.

Jul 22, 2010 | 1983 Chevrolet Impala

1 Answer

Replace valve cover gaskets on a 2000 frontier v 6


torque specs for the rocker cover (valve cover) screws:
9 - 26 inch lbs
step one- 9 in lbs step 2- 18 in lbs step 3- 26 in lbs
tightening order (see diagram below)


2aa1d8f9-c423-4221-bbed-38a4f9049ad6.png

May 27, 2010 | 2000 Nissan Frontier

1 Answer

Valve cover torque


The spec for the valve cover fasteners is 10 nm (about 7.2 ft/lbs) and the sequence of tightening is diagonally from inside to outside. Joe

please rate my answer as very helpful. thanks

Apr 02, 2010 | 2002 Kia Spectra

1 Answer

I need the torque specs for a ford 300 inline 6


Tighten all bolts to 10 Lbs, then 20 Lbs, then 35 Lbs.
That should be fine for the 6 cylinder flywheel.

Oct 08, 2009 | 1997 Ford F150 Regular Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

218 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...