Question about 1989 Buick LeSabre

1 Answer

Needs oil pan gasket - when reinstalling gasket is there a certain to tighten bolts

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Buick Master
  • 17,970 Answers

Anyone order in there... just position the oil pan and secure with the oil pan-to-engine bolts. Tighten the bolts to 124 inch lbs. (14 Nm). Do NOT overtighten the bolts, as this will damage the oil pan, causing a leak.

needs oil pan gasket - - f020b03.jpg

Hope helps (remember rated and comment this).

Posted on Aug 26, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to do a transmission fluid/filter change on a gmc 1500 2wd v8 350 step by step


Raise the vehicle. Refer to Vehicle Lifting. Place a drain pan under the transmission oil pan. Remove the oil pan drain plug. Remove the oil pan bolts. Remove the oil pan. Remove the gasket. Remove the magnet. Remove the oil filter. Remove the filter neck seal. The transmission oil pan gasket is reusable. Inspect the gasket and replace as needed. Clean the transmission case and the oil pan gasket surfaces with solvent. Install the filter neck seal. Install the oil filter. Install the oil pan gasket to the pan. Install the magnet into the bottom of the pan. Notice: Refer to Fastener Notice in Service Precautions. Install the oil pan to the transmission with seventeen bolts. Tighten the oil pan bolts to 11 Nm (97 inch lbs.) . Apply a small amount of sealant GM P/N 12346004 to the treads of the drain plug. Install the oil pan drain plug. Tighten the oil pan drain plug to 18 Nm (13 ft. lbs.) . Install Dextron Automatic Transmission Fluid. Lower the vehicle.

Jul 04, 2011 | GMC Sierra 1500 Cars & Trucks

2 Answers

Where is trans filter located


Hi,
The follwoing is from the GM Shop Technical Manual.
Changing the filter requires removing the transaxle oil pan and gasket,
Remove or disconnect

bendarden.jpg

  • Raise vehicle and suitably support.
  • Loosen oil pan bolts and drain fluid,
  • Remove oil pan attaching bolts.
  • Remove pan pan and gasket.
  • Remove the oiil filter using a long screwdriver pry filter neck out of the seal.
  • Check oil filter seal for damage or wear. If needed, remove and replace
Install or connect
  • install new oil filter and/or seal.
  • install the old pan gasket since it can be reused, unless sealing ribs are damaged. If damaged, use new gasket.
  • Install the oil pan and attaching bolts.
  • Tighten pan bolts to 13 lb. ft,
  • Lower vehicle.
  • Refill transxle to proper level with DEXRON III or DEXRON-IIE fluid.
  • Checkoil pan gasket for leaks,

May 21, 2011 | 1995 Buick LeSabre

2 Answers

I am replacing the oil pan gasket and the bolt diagram doesnt match the gasket we are putting on the car. I need the tightening order for the 2000 ford taurus lx with ohv. please and thanks!


OKAY LOOKING AT OIL PAN FACING SHALLOW END LEFT SIDE STUDS BOLTS SEQUENCE 13 12 11 10 9 BACK BOLTS 8 7 6 5 OKAY 5 BOLTS WILL BE ONE OF THE RIGHT SIDE STUDS STARTING AT 5 BACK STUD THEN BOLT 4 3 2 1 AND FRONT BOLTS ON FRONT OF PAN AFTER 1 BOLT 15 AND BOLT 14. SEE FRONT BOLTS ON FRONT END OF OIL PAN 14 15 AND 1. WRITE NUMBERS DOWN IN THE SEQUENCE I GAVE YOU ON PAPER. DRAW OIL PAN ROUGH DRAFT PUT THE NUMBERS I GAVE YOU I SAME SEQUENCE THATS YOUR OIL PAN BOLTS SEQUENCE.

Apr 18, 2011 | 2000 Ford Taurus

1 Answer

My 2008 aveo5 is leaking what looks like oil. I looked underneath the car and it looks like it is leaking through the gasket on the engine that is to the left of the drainplug. That is if you are from the...


If the gasket is on the oil pan you may try tightening the bolt. To tighten pan gaskets you'll need to tighten in steps in a crisscross pattern. Snug a bolt move across the pan snug another bolt. Do this until all bolts are snug. Do not over tighten pan gasket bolts or leaks will occur. Just uniformly snuf.

Jan 04, 2011 | 2008 Chevrolet Aveo5

2 Answers

How do you replace a gasket and cover for timing chain and rear seal gasket for oil pan on a 1978 Chevy 350 motor


the oil pan will need to be removed to repalce the rear seal, so replace the front seal and gasket then, replace the timing chain/gears if sloppy, then reinstall the oil pan.

Dec 11, 2010 | Chevrolet Blazer Cars & Trucks

1 Answer

Replacing oil pan on 2003 dodge stratus


Make sure you work in a very clean area when exposing the engine internals such as you will be doing. 

First drain the oil and remove the oil filter. This should be an obvious starting point, but it is still worth mentioning. 

Under the car, you should have a small black metal structural collar that connects the oil pan to the transmission bell housing. Remove the four bolts that mount this, and remove it. Then remove the 10+ small bolts around the edge of the pan. The pan may be stuck very tightly to the engine block. Be careful of the mating surface where the pan contacts the bottom of the engine block. Do not use a metal crow bar or screw driver in an attempt to separate the oil pan from the block. Wiggling the pan back and forth or prying with a hard plastic or composite prying device should separate the pan with minimal effort. 

If you are installing a new oil pan, buy a new oil pan gasket. Also purchase a small tube of gasket sealant. It is very inexpensive and is without a doubt one of the most valuable oil pan purchases you will make.

Remove all traces of old gasket material and sealant from both mating surfaces. Acetone will dissolve old gasket material, and so will gasoline, to a lesser degree. Check to see that there is no obvious warping on either mating surface by pressing a straightedge to each surface and checking for any gaps. Minuscule warping is not uncommon and will not cause any problems.

Apply a thin bead of the sealant on the flat mating edge and position the gasket on the pan. Press the gasket straight onto the bead of sealant and wipe off any excess. 

Then apply another thin bead of sealant to engine block mating surface, being careful not to leave an excessive amount inside the engine. A small amount will not do any damage, but always best to introduce as few foreign substances to your oil as possible. Position the pan on the block and reinstall the oil pan bolts. Tighten the bolts in three steps, working up to full torque. When tightening the bolts, always begin in the center of the pan and work toward the ends. This is a common tightening sequence and will ensure a firm, even fit.

Once all the bolts are reinstalled, reattach the structural collar and torque those bolts as well.

Give the gasket sealant an hour to cure before refilling with oil. After that you should be all set. Best of luck to you.

Nov 06, 2009 | 2003 Dodge Stratus

2 Answers

How can i remove the oil pan gasket?


REMOVAL & INSTALLATION

The radio may contain a coded theft protection circuit. Always obtain the code number before disconnecting the battery.
2.2L, 2.3L and 2.7L Engines
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Drain the engine oil into a sealable container.
  4. Install the drain bolt with a new gasket. Tighten the bolt to 33 ft. lbs. (44 Nm).
  5. Remove the front wheels and the splash shield.
  6. Remove the center beam.
5dbe5cd.jpg

Fig. To gain access to the oil pan, remove the center beam-2.2L and 2.3L engines
  1. Detach the Oxygen sensor (O 2 S) electrical connector.
  2. Remove the bolts from the support bracket on the exhaust pipe.
  3. Remove the nuts attaching the exhaust pipe to the exhaust manifold and the catalytic converter.
  4. Remove the exhaust pipe and discard the gaskets.
  5. If equipped with an automatic transaxle, remove the converter cover.
  6. If equipped with a manual transaxle, remove the clutch cover.
  7. Remove the oil pan nuts and bolts (in a criss-cross pattern) and the oil pan; if necessary, use a mallet to tap the corners of the oil pan. DO NOT pry on the pan to get it loose.
  8. Clean the oil pan mounting surface of old gasket material and engine oil.
To install:
  1. Install a new oil pan gasket to the oil pan. Apply liquid gasket to the corners of the curved section of the gasket.
  2. Install the oil pan to the engine.
  3. Install the oil pan nuts and bolts and tighten the nuts and bolts in sequence. Tighten the nuts and bolts in 2 steps to 10 ft. lbs. (14 Nm).
  4. If equipped with an automatic transaxle, install the torque converter cover. Tighten the bolts to 108 inch lbs. (12 Nm).
  5. If equipped with a manual transaxle, install the clutch cover. Tighten the bolts to 108 inch lbs. (12 Nm).
  6. Install the exhaust pipe with new gaskets and new locknuts. Tighten the nuts attaching the exhaust pipe to the manifold to 40 ft. lbs. (54 Nm)and tighten the nuts attaching the exhaust pipe to the catalytic converter to 25 ft. lbs. (33 Nm). Install the bolts to the exhaust pipe support bracket and tighten the bolts to 13 ft. lbs. (18 Nm).
  7. Attach the Oxygen sensor (O 2 S) electrical connector.
  8. Install the center beam and tighten the mounting bolts as follows:

    Prelude: 43 ft. lbs. (60 Nm) Accord: 37 ft. lbs. (50 Nm)
  9. Install the splash shield and tighten the mounting bolts to 84 inch lbs. (10 Nm).
  10. Install the front wheels.
  11. Lower the vehicle and fill the engine with oil.
  12. Connect the negative battery cable and enter the radio security code.
  13. Start the engine and check for leaks.

039a698.jpg

Fig. Oil pan mounting bolt tightening sequence-2.2L and 2.3L engines

402f99d.jpg

Fig. Oil pan tightening sequence-2.7L engines


3.0L Engine

fc8e34b.jpg

Fig. Tighten the oil pan bolts in three steps, in sequence, to 8.7 ft. lbs. (12 Nm)

  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Remove the engine undercover.
  4. Drain the engine oil and replace the drain plug.
  5. Remove the front exhaust pipe.
  6. Remove the oil pan mounting bolts.
  7. Hammer a seal cutter between the engine block and oil pan to break the seal.
  8. Remove the oil pan.
To install:
  1. Clean the oil pan flange and engine block mounting surface.
  2. Apply sealant to the oil pan flange. Be sure to apply sealant toward the inside of the bolt holes.
  3. Install the oil pan on the engine. Tighten the bolts in sequence to 8.7 ft. lbs. (12 Nm).
  4. Install the exhaust pipe.
  5. Install the undercover.
  6. Lower the vehicle.
WARNING Operating the engine without the proper amount and type of engine oil will result in severe engine damage.
  1. Refill the engine with the correct amount of oil.
  2. Connect the negative battery cable.
  3. Start the engine and check for leaks.

I really hope help you with this (remember rated this help) Good luck.

Sep 23, 2009 | 1996 Honda Accord

1 Answer

How do I change the tranny fluid in my 1998 cadillac catera


Fluid - A/T: Service and Repair
Transmission Fluid and Oil Filter Changing
REMOVAL PROCEDURE
1. Raise and suitably support the vehicle. Refer to Vehicle Lift Points.
2. Place drain pan under pan
3. Remove oil pan bolts from front and sides only.
4. Loosen the rear oil pan bolts approximately four turns.
5. Lightly tap the oil pan with a rubber mallet or pry to drain the fluid from main case.
6. Remove the oil pan bolts from rear oil pan and gasket.
7. Remove front oil pan bolts leaving one corner bolt in loosely.
8. Lightly tap oil pan with rubber mallet or pry to drain fluid.
9. Remove the following remaining components:
^ The front oil pan bolts
^ The oil pan
^ The gasket
10. Remove the oil filter bolts and filter.
11. Clean the following components:
^ The transmission case
^ The front adapter case
^ The oil pan gasket surfaces with solvent
^ Air dry
^ All traces of gasket material must be removed
INSTALLATION PROCEDURE
1. Install the gasket.
2. Install the oil filter.
3. Install the bolts.
^ Tighten the transmission oil filter bolts to 20 Nm (15 ft. lbs.).
NOTICE: Refer to Fastener Notice in Service Precautions.
4. Install the front oil pan.
5. Install the front oil pan gasket
6. Install the front oil pan bolts
^ Tighten the front oil pan bolts to 11 Nm (96 inch lbs.).
7. Install the following components:
^ Install the pan
^ Install the gasket
^ Install the bolts
^ Tighten the oil pan bolts to 11 Nm (96 inch lbs.).
8. Refill the transmission with DEXRON III through oil pan fill plug on the side of the (main case) oil pan. Fill the transmission to lower edge of oil
pan fill. Fill plug opening using and oil suction gun.
^ Tighten the oil pan fill plug to 45 Nm (33 ft. lbs.).
9. Lower the vehicle.
10. Check the transmission fluid level. Refer to Transmission Fluid Checking Procedure.

Sep 13, 2009 | 1998 Cadillac Catera

1 Answer

My oil pan is leaking around the corners. What do i do?


drain out hte old oil, Remove oil pan bolts, remove old oil pan gasket, install new gasket, install oil pan, tighten oil pan bolts to 17 ft. lbs. DO NOT OVER TIGHTEN as this will distort the gasket and cause another leak.

Jul 16, 2009 | 2003 Nissan Altima

2 Answers

05 susuki forenza


Removal Procedure
1. Disconnect the negative battery cable.
2. Drain the engine oil from the engine crankcase.
3. Remove the exhaust flex pipe retaining nuts from
the exhaust manifold.
4. Remove the exhaust flex pipe retaining nuts from
the catalytic converter or the connecting pipe.
5. Remove the exhaust flex pipe.
6. Remove the oil pan flange–to–transaxle retaining
bolts.
7. Remove the oil pan retaining bolts.
8. Remove the oil pan from the engine block.
Cleaning Procedure
1. Clean the oil pan sealing surface.
2. Clean the engine block sealing surface.
3. Clean the oil pan retaining bolts.
4. Clean the oil pan attaching bolt holes in the engine
block.
5. Clean the oil pan scraper.
Installation Procedure
1. Coat the new oil pan gasket with sealant.
Important : Install the oil pan within 5 minutes after applying
the liquid gasket to the oil pan.
2. Install the oil pan to the engine block.
3. Install the oil pan retaining bolts.
Tighten
Tighten the oil pan retaining bolts to 10 NSm (89 lb–in).
4. Install the oil pan flange–to–transaxle retaining
bolts.
Tighten
Tighten the oil pan flange–to–transaxle bolts to 40
NSm (30 lb–ft).
5. Install the exhaust flex pipe.
6. Install the exhaust flex pipe retaining nuts to the
exhaust manifold.
Tighten
Tighten the exhaust flex pipe–to–exhaust manifold
retaining nuts to 35 NSm (26 lb–ft).
7. Install the exhaust flex pipe retaining nuts to the
catalytic converter or the connecting pipe.
Tighten
Tighten the exhaust flex pipe–to–catalytic converter
or connecting pipe retaining nuts to 35 NSm (26 lb–ft).
8. Connect the negative battery cable.
9. Install the oil pan drain plug.
Tighten
Tighten the oil pan drain plug to 35 NSm (26 lb–ft).
10. Refill the engine crankcase with engine oil.

Jun 14, 2008 | 2005 Suzuki Forenza

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...