Question about Chevrolet Classic

Open Question

How do I remove a 1970 chevelle dash - Classic Chevrolet Cars & Trucks

Posted by on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

di62
  • 10 Answers

SOURCE: removing dash board from 1969 chevelle

you will find bolts in the defrost air vents and under any speaker covers. also in the glove box. make things easy and remove the windshield first. can be done with the windshield in place but much harder.

Posted on Dec 04, 2008

  • 1 Answer

SOURCE: unable to remove dash pad 1967 chevelle

Go to Team chevelle dot com great advice for every problem in the forums

Posted on Dec 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install headers on a 1970 chevelle SS 454 BBC


You must remove the starter and oil filter. Then do one side at a time remove mtr. mount bolt and jack up eng. and bring header up from the bottom.

Feb 17, 2015 | Cars & Trucks

1 Answer

How set up a manual chokein a ford falcon


I put one in a 1970 Chevelle. I bought the hand choke cable with pull lever and under dash mounting bracket. Mounted pull lever under the dash, drilled a hole in the firewall as high as I could, ran the cable out to the engine compartment. Mounted the holding bracket to the motor as close to carb as possible on the intake, then attached to the choke arm that works the butterfly plate in the carb throat. Cut to fit as tight as possible with butterfly plate closed and push lever all the way in. As you pull the hand lever out inside the car, it opens the butterfly plate to achieve the optimum air fuel mixture you desire to make the engine run smoothly. Sometimes you must go the opposite, lever out and plate closed, depending on the way the carb is set up, and work it the opposite way.

Jul 29, 2014 | Cars & Trucks

1 Answer

Reinstall headlight adjusters for 1970 Chevelle


Not sure I understand question. Do you need to just replace the adjuster? Remove trim ring from other side and match it. Are you missing the retaining spring? Is the headlamp bucket damaged? Usually when one thing is bad or in pieces, I'll disassemble another very carefully to see whats missing or broke. Parts stores usually have repair or "HELP" parts for just such problems.Good Luck

Oct 30, 2012 | Cars & Trucks

1 Answer

How do I wire up.1970 chevelle SS with factory tach


The tach runs off the coil voltage. One of the tach wires would go to the neg side of the coil, I think.
You may need to look for a shop manual to get the wiring diagram.
Car clubs would be a good place to start.

Jul 03, 2012 | Cars & Trucks

1 Answer

I needto tell me where all the vacuum lines go on my 1970 impala 400 , rochester 2bb.


Hello
Due to the age of the car we do not have diagrams available for free on the Internet. Below you will find a source for the original factory repair manual which would have all the information in it. Here is the link to the manual.
http://www.faxonautoliterature.com/1970-Chevy-Car-Repair-Shop-Manual-Chevelle-El-Camino-Monte-Carlo-Nova-Caprice-Impala-Corvette-P10695.aspx

Aug 18, 2011 | Chevrolet Impala Cars & Trucks

1 Answer

I am removing the dash from my 1967 chevelle, got all the switches out w/ the exception of the ignition switch, I can turn the bezel so far and then it appears to stop turning and the switch is still in...


I have a '67 Chevelle SS and I have to replace the ignition switch too. I tried removing the very top edge of the dash by removing all of the screws but it won't budge. How did you remove yours?

Apr 04, 2010 | Chevrolet Classic Cars & Trucks

1 Answer

Removing dash board from 1969 chevelle


you will find bolts in the defrost air vents and under any speaker covers. also in the glove box. make things easy and remove the windshield first. can be done with the windshield in place but much harder.

Dec 04, 2008 | Chevrolet Chevy Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

307 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...