Question about 2002 Chevrolet S-10

1 Answer

Hi I just recently found the firing order on here an was wondering if u could help me one last time I was driving my truck on day an it started to run really **** an then died I put a new fuel pump in An was able to get it home the next day went to go start it an it starts up barley with the pedal to the floor an it idles at like 500 for 10 to 15 seconds maybe an dies I've replaced fuel pump,fuel pressure regulator,spark plugs wires cap rotor an coil I put new battery in it an it did have a check engine light on for maf sensor so I replaced that also still does not run right I also put a new throttle pisitioning sensor in I do t know what's wrong an money is really tight if someone could plz help me out if u think u might kno what it is thanks my email is philzson19@aol.com thanks again Kyle

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,092 Answers

You forgot to rate my help, on the fire order, but I can still help.

Posted on Aug 26, 2010

  • 2 more comments 
  • Alexander Mimun
    Alexander Mimun Aug 26, 2010

    Before I can give you a solution, does your engine put out black smoke, when it does start?

  • Alexander Mimun
    Alexander Mimun Aug 26, 2010

    Does it put out black smoke from tail pipe?

  • philzson19 Aug 26, 2010

    No I got it to run at idle but wen I give it throttle it shuts off an it it shuts off it's a pain invthe *** to get it running I have to pump the **** out of the throttle

  • Alexander Mimun
    Alexander Mimun Aug 26, 2010

    It's going to be your camshaft sensor, coil is fireing but at the wrong time, camshaft sensor sit in the ignition distributor, also know as ignition pick up coil.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Seat Leon Stylance TSI 1.4 Starting Problems


I suspect that it is in the starter and the problem will be in the starter pinion gear and over run clutch. There will be no codes for this area as it is not electronically controlled . I would have the starter bench tested to eliminate it as a source of the problem as it may also be the armature is poling out ( worn bushes)

May 22, 2014 | 2009 Seat Leon 2.0

1 Answer

Firing order for a vn v6 1988 commodore


Hi there:
On Holden - Commodore, VN 3.8 Litre V6 (1988-1991)...



Firing order: 1-6-5-4-3-2



Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Sep 13, 2012 | Cars & Trucks

1 Answer

The engine misfires when accelerating


Depending on your Grand Marquis's mileage...it sounds like plug wires and plugs...(worn out) and or engine timing/firing order? If plug wires recently changed...the spark plug wires are in the wrong firing order...confirm the firing order from your local parts store by phone...and retrace each one...always start with #1 cylinder...hope this helps.

Apr 25, 2011 | 2000 Mercury Grand Marquis

1 Answer

Hi i have Land Rover Discovery 3 model is 1996 V8 engine 3.9 Gasoline. Engine is cranking but not starting when i check Spark Plugs it comes vet, i have check timing and firing order i think firing order...


Attached is link to Rave Manuals (Rover Bible) BTW yours is listed as Discovery (not 3 if it's 1996) These have exploded wiring diagrams & pics - http://www.landroverresource.com/

Apr 07, 2011 | Land Rover Discovery Cars & Trucks

1 Answer

I have an 89 ford f-150 cranks wont start got fire, timing is right, fuel pump is pumping


Hi,
Since you're sure that you are getting gas and fire and timing is right... (also check firing order), has anything been done recently that could help you locate the problem? Such as removed distributor (could be 180 degrees out)? New plug wires (maybe crossed)?
All else I could recommend is checking cylinder compression (In case the valves are the problem)... The engine timing chain could need replacing...
Hope this helps... Good luck!

Oct 13, 2009 | 1989 Ford F 150

1 Answer

Engine cuts out when driving


i would check the fuel filter, if thats good, it may be a grounding problem, my corolla was doing the same thing, making me so mad! LOL turns out the battery was just bouncing up and shorting out on the hood! any way good luck and hope this helps

Sep 29, 2009 | 1998 Toyota Corolla

1 Answer

Backfiring through exhaust


you may need too replace the timing gear!!!!!!

Jun 03, 2009 | 1994 GMC Sonoma

2 Answers

My 1993 honda prelude was recently stolen, and it has some issues


hi,

hummm, lets see here. you had plug wires stolen and you put new ones back on the vehicle. sounds like you may have gotten the firing order out of place. for a 4cyl the firing order will be 1-3-4-2. so as you look at the distrubutor, # 1 cyl should be going to the plug closest to the drive belts. and then 2 next and so on....

the way to tell where #1 cyl on distrubutor is.. "bump" over the starter until you see a white mark on the belt pulley line up with the marker on the timing belt cover. when you get that done. remove the distrubutor cap and look at which plug wire i's pointing to... it should be #1.... if not you have a firing order problem, (check all other wire orders... ) start with that plug wire being # one and then next (don't remember which way this engine goes clockwise or counter clockwise) but make sure the next in line is 3, and then 4, and then 2..... got it? ...... good luck and hope this helped.

Dec 27, 2008 | 1993 Honda Prelude

1 Answer

Ignition Wiring


Hi,

To my knowledge, firing order is 1-8-4-3-6-5-7-2 clockwise on the distributor cap with the Number 1 post pointed towards the Number 1 cylinder. The cylinders are numbered 1-3-5-7 (front towards the back) driver side while the passenger side/bank are numbered 2-4-6-8 (likewise front to back).

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards.

Thank you for using FixYa.

Jun 04, 2008 | 1993 Chevrolet K1500

Not finding what you are looking for?
2002 Chevrolet S-10 Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...