Question about 1993 Ford F250

1 Answer

How does transmission come out - 1993 Ford F250

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 6,826 Answers

how does transmission come out - prev.gif next.gif Transmission Assembly REMOVAL & INSTALLATION C6

  1. Disconnect the negative battery cable.
  2. From in the engine compartment, remove the two upper converter housing-to-engine bolts.
  3. Disconnect the neutral switch wire at the in-line connector.
  4. Remove the bolt securing the fluid filler tube to the engine cylinder head.
  5. Raise and support the truck on jackstands.
  6. Place the drain pan under the transmission fluid pan. Starting at the rear of the pan and working toward the front, loosen the attaching bolts and allow the fluid to drain. Finally remove all of the pan attaching bolts except two at the front, to allow the fluid to further drain. With fluid drained, install two bolts on the rear side of the pan to temporarily hold it in place.
  7. Remove the converter drain plug access cover from the lower end of the converter housing.
  8. Remove the converter-to-flywheel attaching nuts. Place a wrench on the crankshaft pulley attaching bolt to turn the converter to gain access to the nuts.
  9. With the wrench on the crankshaft pulley attaching bolt, turn the converter to gain access to the converter drain plug. Place a drain pan under the converter to catch the fluid and remove the plug. After the fluid has been drained, reinstall the plug.
  10. On 2WD drive models, disconnect the driveshaft from the rear axle and slide shaft rearward from the transmission. Install a seal installation tool in the extension housing to prevent fluid leakage.
  11. Disconnect the speedometer cable from the extension housing.
  12. Disconnect the downshift and manual linkage rods from the levers at the transmission.
  13. Disconnect the oil cooler lines from the transmission.
  14. Remove the vacuum hose from the vacuum diaphragm unit. Remove the vacuum line retaining clip.
  15. Disconnect the cable from the terminal on the starter motor. Remove the three attaching bolts and remove the starter motor.
  16. On 4WD drive models remove the transfer case.
  17. Remove the two engine rear support and insulator assembly-to-attaching bolts.
  18. Remove the two engine rear support and insulator assembly-to-extension housing attaching bolts.
  19. Remove the six bolts securing the No. 2 crossmember to the frame side rails.
  20. Raise the transmission with a transmission jack and remove both crossmembers.
  21. Secure the transmission to the jack with the safety chain.
  22. Remove the remaining converter housing-to-engine attaching bolts.
  23. Move the transmission away from the engine. Lower the jack and remove the converter and transmission assembly from under the vehicle. To install:
  24. Tighten the converter drain plug.
  25. Position the converter on the transmission making sure the converter drive flats are fully engaged in the pump gear.
  26. With the converter properly installed, place the transmission on the jack. Secure the transmission on the jack with the chain.
  27. Rotate the converter until the studs and drain plug are in alignment with their holes in the flywheel.
  28. Move the converter and transmission assembly forward into position, using care not to damage the flywheel and the converter pilot. The converter must rest squarely against the flywheel. This indicates that the converter pilot is not binding in the engine crankshaft.
  29. Install the converter housing-to-engine attaching bolts and tighten them to 65 ft. lbs. (88 Nm) for the diesel; 50 ft. lbs. (68 Nm) for gasoline engines.
  30. Remove the transmission jack safety chain from around the transmission.
  31. Position the No. 2 crossmember to the frame side rails. Install and tighten the attaching bolts.
  32. Install transfer case on 4WD drive models.
  33. Position the engine rear support and insulator assembly above the crossmember. Install the rear support and insulator assembly-to-extension housing mounting bolts and tighten the bolts to 45 ft. lbs. (61 Nm).
  34. Lower the transmission and remove the jack.
  35. Secure the engine rear support and insulator assembly to the crossmember with the attaching bolts and tighten them to 80 ft. lbs. (108 Nm).
  36. The balance of installation is the reverse of removal.

Posted on Aug 26, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I want to remove my trasmission


Yes the engine has to be out,its not a easy task to replace transmission.You will required professional tools and wrench/ratchets.
Also its very time consuming.

For your help,i suggest you few help links with accurate solutions,showing how exactly to replace transmission and other transmission components.
---------------
Click the link below:-----

HOW TO REPLACE A MANUAL TRANSMISSION

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-manual-transmission.html

--------------

HOW TO REPLACE TRANSMISSION COOLER LINES

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-transmission-cooler.html

-----------

HOW TO CHECK AUTOMATIC TRANSMISSION FLUID LEVEL

http://schematicsdiagram.blogspot.com/2011/07/how-to-check-automatic-transmission.html

------------

HOW TO CHANGE AUTOMATIC TRANSMISSION FLUID AND FILTER

http://schematicsdiagram.blogspot.com/2011/07/how-to-change-automatic-transmission.html


HOW TO REPLACE A TRANSMISSION MOUNT

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-transmission-mount.html

------------------

DSG automatic transmission problem

http://whatisbyme.blogspot.in/2012/07/dsg-automatic-transmission-problem.html

--------------

Transmission problem?

http://schematicsdiagram.blogspot.com/2012/01/transmission-problem.html

---------------

2004 Chrysler 300m: Transmission Relearn Procedure?

http://repairhelpcenter.blogspot.in/2012/06/2004-chrysler-300m-transmission-relearn.html

----------------

How do you change transmission fluid on Pontiac?

http://schematicsdiagram.blogspot.in/2012/03/how-do-you-change-transmission-fluid-on.html

-------------

Filling Transmission fluid on 2001 Volvo c70?

http://schematicsdiagram.blogspot.in/2012/02/filling-transmission-fluid-on-2001.html

----------------

2002 Isuzu trooper Transmission fluid fill up?

http://schematicsdiagram.blogspot.in/2012/02/2002-izusu-trooper-transmission-fluid.html

-----------------

AUDI V8 TRANSMISSION FLUID

http://whoisbyme.blogspot.in/2012/07/audi-v8-transmission-fluid.html

Where to fill Transmission Fluid on 2001 ford focus

http://technoanswers.blogspot.com/2012/10/where-to-fill-transmission-fluid-on.html

--------------

Coolant enters in transmission on Toyota Land cruiser?

http://schematicsdiagram.blogspot.com/2012/01/coolant-enters-in-transmission-on.html

--------------------

Engine stumbles and shuts off in forward gear on Toyota Land Cruiser?

http://schematicsdiagram.blogspot.com/2012/01/engine-stumbles-and-shuts-off-in.html

--------------------

Car engine Overheats and transmission starts slipping?

http://schematicsdiagram.blogspot.com/2011/12/car-engine-overheats-and-transmission.html

----------------

Manual Transmission Clutch System Failures?

http://repairhelpcenter.blogspot.com/2011/11/manual-transmission-clutch-system.html

---------------------

Automatic transmission will not go into high gear?

http://howtobyme.blogspot.com/2011/11/automatic-transmission-will-not-go-into.html

------------------

Transmission fluid gets into radiator?

http://schematicsdiagram.blogspot.com/2011/12/transmission-fluid-gets-into-radiator.html

---------------

Dodge Anti slip System is not operating?

http://whatisbyme.blogspot.in/2012/07/dodge-anti-slip-system-is-not-operating.html

--------------

How to check Transmission fluid on 1996 Chevrolet Camaro?

http://schematicsdiagram.blogspot.com/2011/12/how-to-check-transmission-fluid-on-1996.html

-------------

Transmission fault light on car dash?

http://schematicsdiagram.blogspot.com/2011/12/transmission-fault-light-on-car-dash.html

-----------------

Filled T-IV fluid instead of WS transmission fluid?

http://repairhelpcenter.blogspot.com/2012/01/filled-t-iv-fluid-instead-of-ws.html

----------

Manual transmission very hard to shift from one gear to another?

http://repairhelpcenter.blogspot.com/2012/01/manual-transmission-very-hard-to-shift.html

-------------------

Bell housing and transmission will not come apart on 1996 Toyota Tacoma?

http://repairhelpcenter.blogspot.com/2012/01/bell-housing-and-transmission-will-not.html

--------------------

How to Add transmission fluid on 2002 Isuzu AXIOM?

http://technoanswers.blogspot.in/2012/02/how-to-add-transmission-fluid-on-2002.html

---------------

Chrysler Cirrus Auto Transmission Swap?

http://whoisbyme.blogspot.in/2012/06/chrysler-cirrus-auto-transmission-swap.html


These details will help.

Thanks.

Nov 26, 2012 | Cars & Trucks

1 Answer

92 chevy 3500 6.5 auto trans trouble


For Automatic transmission problem,click the link below:----Automatic transmission troubleshooting:---- http://howtobyme.blogspot.com/2011/11/automatic-transmission-will-not-go-into.html---------Automatic transmission shift lever issues?------- http://technoanswers.blogspot.com/2012/01/automatic-transmission-shift-lever-hard.html
-----------AUTOMATIC TRANSMISSION FLUID LEVEL? --

http://schematicsdiagram.blogspot.com/2011/07/how-to-check-automatic-transmission.html

--------------

AUTOMATIC TRANSMISSION FLUID AND FILTER?
http://schematicsdiagram.blogspot.com/2011/07/how-to-change-automatic-transmission.html
-----------Transmission fault light on car dash? http://schematicsdiagram.blogspot.com/2011/12/transmission-fault-light-on-car-dash.html
--------Transmission shifting problem? http://schematicsdiagram.blogspot.com/2012/01/transmission-shifting-problem-on-toyota.html
--------Transmission Slips out of 2nd gear?

http://repairhelpcenter.blogspot.in/2012/02/transmission-slips-out-of-2nd-gear.html

-----------
OD light flashing and transmission fluid leaking?

http://repairhelpcenter.blogspot.in/2012/02/od-light-flashing-and-transmission.html

----------
Why Transmission fluid leaks near radiator?

http://repairhelpcenter.blogspot.in/2012/02/transmission-fluid-leaks-near-radiator.html

----------
transmission fluid leaking?

http://technoanswers.blogspot.in/2012/02/ford-windstar-transmission-fluid.html

-------------
****** wont go in reverse?

http://technoanswers.blogspot.in/2012/02/dodge-neon-wont-go-in-reverse.html

-------------
Automatic transmission will not go into reverse? http://technoanswers.blogspot.in/2012/02/dodge-automatic-transmission-will-not.html
----------Transmission is making buzzing noise? http://technoanswers.blogspot.in/2012/02/transmission-is-making-buzzing-noise.html
-----------This will help.Thanks.

Feb 22, 2012 | 1992 Chevrolet C/K 3500

1 Answer

Tranmission ands four wheel drive locked out


For Automatic transmission problem,click the link below:---- Automatic transmission troubleshooting:----

http://howtobyme.blogspot.com/2011/11/automatic-transmission-will-not-go-into.html

---------
Automatic transmission shift lever issues?-------

http://technoanswers.blogspot.com/2012/01/automatic-transmission-shift-lever-hard.html

-----------
AUTOMATIC TRANSMISSION FLUID LEVEL? --

http://schematicsdiagram.blogspot.com/2011/07/how-to-check-automatic-transmission.html

--------------

AUTOMATIC TRANSMISSION FLUID AND FILTER?

http://schematicsdiagram.blogspot.com/2011/07/how-to-change-automatic-transmission.html

-----------
Transmission fault light on car dash?

http://schematicsdiagram.blogspot.com/2011/12/transmission-fault-light-on-car-dash.html

--------
Transmission shifting problem?

http://schematicsdiagram.blogspot.com/2012/01/transmission-shifting-problem-on-toyota.html

--------
Transmission Slips out of 2nd gear?

http://repairhelpcenter.blogspot.in/2012/02/transmission-slips-out-of-2nd-gear.html

-----------
OD light flashing and transmission fluid leaking?

http://repairhelpcenter.blogspot.in/2012/02/od-light-flashing-and-transmission.html

----------
Why Transmission fluid leaks near radiator?

http://repairhelpcenter.blogspot.in/2012/02/transmission-fluid-leaks-near-radiator.html

----------
Transmission fluid leaking?

http://technoanswers.blogspot.in/2012/02/ford-windstar-transmission-fluid.html

-------------
****** wont go in reverse?

http://technoanswers.blogspot.in/2012/02/dodge-neon-wont-go-in-reverse.html

-------------
Automatic transmission will not go into reverse?

http://technoanswers.blogspot.in/2012/02/dodge-automatic-transmission-will-not.html

----------
Transmission is making buzzing noise?

http://technoanswers.blogspot.in/2012/02/transmission-is-making-buzzing-noise.html

-----------

This will help.

Thanks.

Feb 22, 2012 | 1998 Mitsubishi Montero Sport

1 Answer

Disconnect shift linkage


For Automatic transmission problem,click the link below:---- Automatic transmission troubleshooting:----

http://howtobyme.blogspot.com/2011/11/automatic-transmission-will-not-go-into.html

---------
Automatic transmission shift lever issues?-------

http://technoanswers.blogspot.com/2012/01/automatic-transmission-shift-lever-hard.html

-----------
AUTOMATIC TRANSMISSION FLUID LEVEL? --

http://schematicsdiagram.blogspot.com/2011/07/how-to-check-automatic-transmission.html

--------------

AUTOMATIC TRANSMISSION FLUID AND FILTER?

http://schematicsdiagram.blogspot.com/2011/07/how-to-change-automatic-transmission.html

-----------
Transmission fault light on car dash?

http://schematicsdiagram.blogspot.com/2011/12/transmission-fault-light-on-car-dash.html

--------
Transmission shifting problem?

http://schematicsdiagram.blogspot.com/2012/01/transmission-shifting-problem-on-toyota.html

--------
Transmission Slips out of 2nd gear?

http://repairhelpcenter.blogspot.in/2012/02/transmission-slips-out-of-2nd-gear.html

-----------
OD light flashing and transmission fluid leaking?

http://repairhelpcenter.blogspot.in/2012/02/od-light-flashing-and-transmission.html

----------
Why Transmission fluid leaks near radiator?

http://repairhelpcenter.blogspot.in/2012/02/transmission-fluid-leaks-near-radiator.html

----------
Transmission fluid leaking?

http://technoanswers.blogspot.in/2012/02/ford-windstar-transmission-fluid.html

-------------
****** wont go in reverse?

http://technoanswers.blogspot.in/2012/02/dodge-neon-wont-go-in-reverse.html

-------------
Automatic transmission will not go into reverse?

http://technoanswers.blogspot.in/2012/02/dodge-automatic-transmission-will-not.html

----------
Transmission is making buzzing noise?

http://technoanswers.blogspot.in/2012/02/transmission-is-making-buzzing-noise.html

-----------

This will help.

Thanks.

Feb 11, 2012 | 2003 Mini Cooper

1 Answer

Shifting solenoids on 2002 Lancer.


For Automatic transmission problem,click the link below:---- Automatic transmission troubleshooting:----

http://howtobyme.blogspot.com/2011/11/automatic-transmission-will-not-go-into.html

---------
Automatic transmission shift lever issues?-------

http://technoanswers.blogspot.com/2012/01/automatic-transmission-shift-lever-hard.html

-----------
AUTOMATIC TRANSMISSION FLUID LEVEL? --

http://schematicsdiagram.blogspot.com/2011/07/how-to-check-automatic-transmission.html

--------------

AUTOMATIC TRANSMISSION FLUID AND FILTER?

http://schematicsdiagram.blogspot.com/2011/07/how-to-change-automatic-transmission.html

-----------
Transmission fault light on car dash?

http://schematicsdiagram.blogspot.com/2011/12/transmission-fault-light-on-car-dash.html

--------
Transmission shifting problem?

http://schematicsdiagram.blogspot.com/2012/01/transmission-shifting-problem-on-toyota.html

--------
Transmission Slips out of 2nd gear?

http://repairhelpcenter.blogspot.in/2012/02/transmission-slips-out-of-2nd-gear.html

-----------
OD light flashing and transmission fluid leaking?

http://repairhelpcenter.blogspot.in/2012/02/od-light-flashing-and-transmission.html

----------
Why Transmission fluid leaks near radiator?

http://repairhelpcenter.blogspot.in/2012/02/transmission-fluid-leaks-near-radiator.html

----------
Transmission fluid leaking?

http://technoanswers.blogspot.in/2012/02/ford-windstar-transmission-fluid.html

-------------
****** wont go in reverse?

http://technoanswers.blogspot.in/2012/02/dodge-neon-wont-go-in-reverse.html

-------------
Automatic transmission will not go into reverse?

http://technoanswers.blogspot.in/2012/02/dodge-automatic-transmission-will-not.html

----------
Transmission is making buzzing noise?

http://technoanswers.blogspot.in/2012/02/transmission-is-making-buzzing-noise.html

-----------

This will help.

Thanks.

Feb 08, 2012 | 2002 Mitsubishi Lancer

1 Answer

My 1993 chrysler concorde transmission will not shift into overdrive, had another transmission placed, has same prob, what could be causing it?


For Automatic transmission problem,click the link below:---- Automatic transmission troubleshooting:----

http://howtobyme.blogspot.com/2011/11/automatic-transmission-will-not-go-into.html

---------
Automatic transmission shift lever issues?-------

http://technoanswers.blogspot.com/2012/01/automatic-transmission-shift-lever-hard.html

-----------
AUTOMATIC TRANSMISSION FLUID LEVEL? --

http://schematicsdiagram.blogspot.com/2011/07/how-to-check-automatic-transmission.html

--------------

AUTOMATIC TRANSMISSION FLUID AND FILTER?

http://schematicsdiagram.blogspot.com/2011/07/how-to-change-automatic-transmission.html

-----------
Transmission fault light on car dash?

http://schematicsdiagram.blogspot.com/2011/12/transmission-fault-light-on-car-dash.html

--------
Transmission shifting problem?

http://schematicsdiagram.blogspot.com/2012/01/transmission-shifting-problem-on-toyota.html

--------
Transmission Slips out of 2nd gear?

http://repairhelpcenter.blogspot.in/2012/02/transmission-slips-out-of-2nd-gear.html

-----------
OD light flashing and transmission fluid leaking?

http://repairhelpcenter.blogspot.in/2012/02/od-light-flashing-and-transmission.html

----------
Why Transmission fluid leaks near radiator?

http://repairhelpcenter.blogspot.in/2012/02/transmission-fluid-leaks-near-radiator.html

----------
Transmission fluid leaking?

http://technoanswers.blogspot.in/2012/02/ford-windstar-transmission-fluid.html

-------------
****** wont go in reverse?

http://technoanswers.blogspot.in/2012/02/dodge-neon-wont-go-in-reverse.html

-------------
Automatic transmission will not go into reverse?

http://technoanswers.blogspot.in/2012/02/dodge-automatic-transmission-will-not.html

----------
Transmission is making buzzing noise?

http://technoanswers.blogspot.in/2012/02/transmission-is-making-buzzing-noise.html

-----------

This will help.

Thanks.

Feb 07, 2012 | 1993 Chrysler Concorde

1 Answer

On a 95 caprice classic, what would cause the transmission to slip?


For Automatic transmission problem,Check the list of help links below.click the link below:----Automatic transmission troubleshooting:----

http://howtobyme.blogspot.com/2011/11/automatic-transmission-will-not-go-into.html

---------
Automatic transmission shift lever issues?-------

http://technoanswers.blogspot.com/2012/01/automatic-transmission-shift-lever-hard.html

-----------
AUTOMATIC TRANSMISSION FLUID LEVEL? --

http://schematicsdiagram.blogspot.com/2011/07/how-to-check-automatic-transmission.html

--------------

AUTOMATIC TRANSMISSION FLUID AND FILTER?

http://schematicsdiagram.blogspot.com/2011/07/how-to-change-automatic-transmission.html

-----------
Transmission fault light on car dash?

http://schematicsdiagram.blogspot.com/2011/12/transmission-fault-light-on-car-dash.html

--------
Transmission shifting problem?

http://schematicsdiagram.blogspot.com/2012/01/transmission-shifting-problem-on-toyota.html

--------
Transmission Slips out of 2nd gear?

http://repairhelpcenter.blogspot.in/2012/02/transmission-slips-out-of-2nd-gear.html

-----------
OD light flashing and transmission fluid leaking?

http://repairhelpcenter.blogspot.in/2012/02/od-light-flashing-and-transmission.html

----------
Why Transmission fluid leaks near radiator?

http://repairhelpcenter.blogspot.in/2012/02/transmission-fluid-leaks-near-radiator.html

----------
transmission fluid leaking?

http://technoanswers.blogspot.in/2012/02/ford-windstar-transmission-fluid.html

-------------
****** wont go in reverse?

http://technoanswers.blogspot.in/2012/02/dodge-neon-wont-go-in-reverse.html

-------------
Automatic transmission will not go into reverse?

http://technoanswers.blogspot.in/2012/02/dodge-automatic-transmission-will-not.html

----------
Transmission is making buzzing noise?

http://technoanswers.blogspot.in/2012/02/transmission-is-making-buzzing-noise.html

-----------

This will help.

Thanks.

Feb 07, 2012 | 1995 Chevrolet Caprice Classic

1 Answer

TORQUE CONVERTER CLUTCH SOLENOID


For Automatic transmission problem,Check the list of help links below.click the link below:----Automatic transmission troubleshooting:----

http://howtobyme.blogspot.com/2011/11/automatic-transmission-will-not-go-into.html

---------
Automatic transmission shift lever issues?-------

http://technoanswers.blogspot.com/2012/01/automatic-transmission-shift-lever-hard.html

-----------
AUTOMATIC TRANSMISSION FLUID LEVEL? --

http://schematicsdiagram.blogspot.com/2011/07/how-to-check-automatic-transmission.html

--------------

AUTOMATIC TRANSMISSION FLUID AND FILTER?

http://schematicsdiagram.blogspot.com/2011/07/how-to-change-automatic-transmission.html

-----------
Transmission fault light on car dash?

http://schematicsdiagram.blogspot.com/2011/12/transmission-fault-light-on-car-dash.html

--------
Transmission shifting problem?

http://schematicsdiagram.blogspot.com/2012/01/transmission-shifting-problem-on-toyota.html

--------
Transmission Slips out of 2nd gear?

http://repairhelpcenter.blogspot.in/2012/02/transmission-slips-out-of-2nd-gear.html

-----------
OD light flashing and transmission fluid leaking?

http://repairhelpcenter.blogspot.in/2012/02/od-light-flashing-and-transmission.html

----------
Why Transmission fluid leaks near radiator?

http://repairhelpcenter.blogspot.in/2012/02/transmission-fluid-leaks-near-radiator.html

----------
transmission fluid leaking?

http://technoanswers.blogspot.in/2012/02/ford-windstar-transmission-fluid.html

-------------
****** wont go in reverse?

http://technoanswers.blogspot.in/2012/02/dodge-neon-wont-go-in-reverse.html

-------------
Automatic transmission will not go into reverse?

http://technoanswers.blogspot.in/2012/02/dodge-automatic-transmission-will-not.html

----------
Transmission is making buzzing noise?

http://technoanswers.blogspot.in/2012/02/transmission-is-making-buzzing-noise.html

-----------

This will help.

Thanks.

Jan 31, 2012 | 2003 Land Rover Discovery

1 Answer

Slipping


For Automatic transmission problem,Check the list of help links below.click the link below:----Automatic transmission troubleshooting:----

http://howtobyme.blogspot.com/2011/11/automatic-transmission-will-not-go-into.html

---------
Automatic transmission shift lever issues?-------

http://technoanswers.blogspot.com/2012/01/automatic-transmission-shift-lever-hard.html

-----------
AUTOMATIC TRANSMISSION FLUID LEVEL? --

http://schematicsdiagram.blogspot.com/2011/07/how-to-check-automatic-transmission.html

--------------

AUTOMATIC TRANSMISSION FLUID AND FILTER?

http://schematicsdiagram.blogspot.com/2011/07/how-to-change-automatic-transmission.html

-----------
Transmission fault light on car dash?

http://schematicsdiagram.blogspot.com/2011/12/transmission-fault-light-on-car-dash.html

--------
Transmission shifting problem?

http://schematicsdiagram.blogspot.com/2012/01/transmission-shifting-problem-on-toyota.html

--------
Transmission Slips out of 2nd gear?

http://repairhelpcenter.blogspot.in/2012/02/transmission-slips-out-of-2nd-gear.html

-----------
OD light flashing and transmission fluid leaking?

http://repairhelpcenter.blogspot.in/2012/02/od-light-flashing-and-transmission.html

----------
Why Transmission fluid leaks near radiator?

http://repairhelpcenter.blogspot.in/2012/02/transmission-fluid-leaks-near-radiator.html

----------
transmission fluid leaking?

http://technoanswers.blogspot.in/2012/02/ford-windstar-transmission-fluid.html

-------------
****** wont go in reverse?

http://technoanswers.blogspot.in/2012/02/dodge-neon-wont-go-in-reverse.html

-------------
Automatic transmission will not go into reverse?

http://technoanswers.blogspot.in/2012/02/dodge-automatic-transmission-will-not.html

----------
Transmission is making buzzing noise?

http://technoanswers.blogspot.in/2012/02/transmission-is-making-buzzing-noise.html

-----------

This will help.

Thanks.

Jan 29, 2012 | 2003 Cadillac Deville

1 Answer

How to remove a transmission for a 2002 GMC Yukon


Removal & Installation 4L60E/4L65E To Remove:
  1. Remove or disconnect the following:
    • Transmission fluid
    • Transmission oil level indicator tube and seal from the transmission
    • Plug the oil level indicator tube opening in the transmission.
    • Remove or disconnect the following:
    • Shift cable end from the transmission shift lever ball stud
    • If equipped with a transfer case, remove the front propeller shaft.
    • Rear propeller shaft.
  2. Plug the transmission oil cooler line connectors in the transmission case.
  3. Remove or disconnect the following:
    • Starter motor.
    • Transfer case, if equipped.
  4. Support the transmission with a transmission jack.
  5. Remove the transmission mount nuts.
  6. Remove the transmission crossmember.
  7. Remove or disconnect the following:
    • Torque converter access plug 4L60E/4L65E removal 9308kg37.gif

    • Flywheel to torque converter bolts
    • The two bolts securing the transmission rear mount to the transmission
    • The transmission vent hose, fuel lines, and the wiring harness from the transmission
    • The stud and the bolt securing the transmission to the engine
    • The six studs and one bolt securing the transmission to the engine. Install tool J21366 onto the transmission bell housing to retain the torque converter. Pull the transmission straight back.
    • The transmission from the vehicle
  8. Flush the transmission oil cooler and cooling lines when you remove the transmission.
To Install:
  1. Install or connect the following:
    • Tool J21366 onto the transmission bell housing to retain the torque converter.
    • Support the transmission with a transmission jack.
  2. Raise the transmission into place and remove the tool from the transmission.
  3. Slide the transmission straight onto the locating pins while lining up the marks on the flywheel and the torque converter. The torque converter must be flush onto the flywheel and rotate freely by hand.
  4. Install or connect the following:
    • Six studs and one bolt securing the transmission to the engine. Tighten the studs and the bolt to 50 Nm (37 ft. lbs.).
    • Stud and bolt securing the transmission to the engine. Tighten the stud and the bolt to 50 Nm (37 ft. lbs.).
    • Flywheel to torque converter bolts. Tighten the stud and the bolt to 46 Nm (63 ft. lbs.).
    • Torque converter access plug.
    • Transmission vent hose, fuel lines, and the wiring harness to the transmission.
    • Two bolts securing the heat shield to the transmission. Tighten the bolt to 17 Nm (13 ft. lbs.).
    • Two bolts securing the transmission rear mount to the transmission. Tighten the bolts to 18 ft. lbs. (25 Nm).
    • Install the transmission crossmember. Tighten the nuts and bolts to 70 ft. lbs. (95 Nm).
  5. Remove the transmission jack from the transmission.
  6. Unplug the transmission oil cooler line connectors in the transmission case.
  7. Install or connect the following:
    • Starter
    • Transmission oil cooler lines to the transmission
    • If equipped with a transfer case, install the front propeller shaft.
    • The rear propeller shaft
    • The shift cable end to the transmission shift lever ball stud
  8. Unplug the oil level indicator tube opening in the transmission.
  9. Install the transmission oil level indicator tube and seal to the transmission.
  10. Tighten the oil pan bolts and fill the transmission with transmission fluid.
  11. Lower the vehicle.
4L80E/4L85E To Remove:
  1. Remove or disconnect the following:
    • Transmission fluid
    • Transmission oil level indicator tube and seal from the transmission
  2. Plug the oil level indicator tube opening in the transmission.
  3. Remove or disconnect the following:
    • Shift cable from the transmission shift lever ball stud
    • If 4WD vehicle, remove the propeller shaft.
    • If RWD vehicle, remove the propeller shaft.
    • The transmission oil cooler lines from the transmission
  4. Plug the transmission oil cooler line connectors in the transmission case.
  5. Remove or disconnect the following:
    • Starter motor
  6. Support the transmission with a transmission jack.
  7. Remove or disconnect the following:
    • The two bolts securing the heat shield to the transmission
    • The transmission vent hose, fuel lines, and the wiring harness from the transmission
    • One nut and one bolt securing the transmission brace to the engine bracket and transmission
    • The two bolts securing the torque converter cover to the engine
    • The four bolts securing the torque converter cover to the transmission
    • The six flywheel to torque converter bolts
    • The two bolts and nut securing the transmission rear mount to the transmission
    • The stud and the bolt on the right side securing the transmission to the engine
    • The remaining six studs and the one bolt securing the transmission to the engine
    • Tool J21366 onto the transmission bell housing to retain the torque converter
    4L80E/4L85E removal 9308kg36.gif

  8. Pull the transmission straight back. Remove the transmission from the vehicle.
  9. Flush the transmission oil cooler and cooling lines when you remove the transmission.
To Install:
  1. Install or connect the following:
    • Tool J21366 onto the transmission bell housing to retain the torque converter
  2. Support the transmission with a transmission jack.
  3. Raise the transmission into place and remove the tool from the transmission.
  4. Slide the transmission straight onto the locating pins while lining up the marks on the flywheel and the torque converter. The torque converter must be flush onto the flywheel and rotate freely by hand.
  5. Install or connect the following:
    • Six studs and one bolt securing the transmission to the engine. Tighten the studs and the bolt to 50 Nm (37 ft. lbs.).
    • The stud and bolt on the right side securing the transmission to the engine. Tighten the stud and the bolt to 50 Nm (37 ft. lbs.).
    • Six flywheel to torque converter bolts. Tighten the bolts to 60 Nm (44 ft. lbs.).
    • The two bolts securing the torque converter cover to the engine. Tighten the bolt to 50 Nm (37 ft. lbs.).
    • The four bolts securing the torque converter cover to the transmission. Tighten the stud and the bolt to 33 Nm (24 ft. lbs.).
    • The transmission vent hose, fuel lines, and the wiring harness to the transmission.
    • The two bolts securing the heat shield to the transmission. Tighten the bolt to 17 Nm (13 ft. lbs.).
    • The two bolts and nut securing the transmission rear mount to the transmission. Tighten the bolts and nut to 25 Nm (18 ft. lbs.).
    • The flywheel to torque converter bolts.
    • One nut and one bolt securing the transmission brace to the engine bracket and transmission. Tighten the bolts and nut to 50 Nm (37 ft. lbs.).
  6. Remove the transmission jack from the transmission.
  7. Install or connect the following:
    • Starter motor
  8. Unplug the transmission oil cooler line connectors in the transmission case.
  9. Connect the transmission oil cooler lines to the transmission.
  10. Install or connect the following:
    • The transfer case
    • The rear propeller shaft
    • The shift cable end to the transmission shift lever ball stud
  11. Unplug the oil level indicator tube opening in the transmission.
  12. Install the transmission oil level indicator tube and seal to the transmission.
  13. Tighten the oil pan bolts and fill the transmission with transmission fluid.
  14. Lower the vehicle.
prev.gif next.gif

Oct 12, 2010 | 2002 GMC Yukon XL

Not finding what you are looking for?
1993 Ford F250 Logo

Related Topics:

219 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...