Question about 1997 Oldsmobile Cutlass Supreme

2 Answers

Where is the camshaft position sensor located on a 1997 Oldsmobile Cutlass Supreme 3.1 ?

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Oldsmobile Master
  • 6,826 Answers

Removal & Installation 3.1L Engine To Remove:
CMP sensor Where is the camshaft position - 93174g24.gif

  1. Disconnect the battery ground cable.
  2. Remove the power steering pump and set aside with the lines connected.
  3. Disconnect the camshaft position (CMP) sensor electrical connector.
  4. Remove the CMP mounting bolt.
  5. Remove the CMP sensor.
  6. Check the O-ring for damage and replace if necessary.
To Install:
NOTE: Lubricate the O-ring with clean engine oil.
  1. Install the camshaft position sensor.
    • Tighten the mounting bolt to 89 in lb (10 Nm).
  2. Connect the CMP sensor electrical connector.
  3. Install the power steering pump.
3.4L Engine To Remove:
  1. Disconnect the negative battery cable.
  2. Detach the electrical connector from the camshaft position sensor.
  3. Remove the sensor retainer bolt and carefully pull the sensor from the camshaft carrier. An O-ring seal may hold the sensor in place. Use care not to lose the O-ring.
Camshaft Position (CMP) sensor removal (3.4L (VIN X) engine) 93174g25.gif

To Install:
  1. Installation is the reverse of the removal procedure.
  2. Before installing a replacement camshaft sensor, lubricate the new O-ring with clean engine oil.
    • Tighten the bolt to 88 inch lbs. (10 Nm). Do not over-tighten.
  3. Connect the negative battery cable.
3.8L Engine To Remove:
  1. Disconnect the negative battery cable.
  2. Detach the electrical connector from the camshaft position sensor. Camshaft Position Sensor removal (3.8L engines)

  3. Remove the retaining screw and separate the sensor from the front cover.
To Install:
  1. Installation the sensor in the front cover.
  2. Tighten the bolt to just 44 inch lbs. (5 Nm). Do not over-tighten. Verify the electrical connector is secure.
  3. Connect the negative battery cable.
prev.gif next.gif

Posted on Aug 26, 2010

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Champion:

    An expert who has answered 200 questions.

  • Contributor
  • 264 Answers

Hi. Your camshaft sensor is located under the power steering pump. You should be able to locate the wiring harness for it on the top of the front valve cover it is usually attached to a metal clip on the upper intake. You will need to remove the P/S pump if you plan to change it.

Posted on Aug 26, 2010

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

john631068
  • 172 Answers

SOURCE: where is the camshaft position sensor located on a

the sensor is located behind the power steering pump the plug is on the front left side of motor red and green wires trace it to the sensor behind the power steering pump 8mm bolt holds sensor in and tough to pry out sometime .....

Posted on Nov 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location for map sensor on a 1994 oldsmobile cutlass supreme 3.4 DOHC?


It's mounted in the right rear notch of the air intake by the fire wall or on the fire wall in that general location. with a vacuum line attached. That is standing in front of the car at the rear top edge of the manifold. Look it up on parts geek you can look at the enlarged picture to see what yo are looking for.

Jul 28, 2016 | 1994 Oldsmobile Cutlass Supreme

1 Answer

1997 Oldsmobile Cutlass Supreme SL Fuse Box diagram


On this website, you find fuse box diagram and description for Oldsmobile Cutlass Supreme (1997)

Oldsmobile Cutlass Supreme 1997 fuse box diagram Auto Genius

Mar 10, 2012 | Cars & Trucks

1 Answer

Where is the camshaft position sensor located


If you have a 3.1l it is under the powersteering pump, take a flashlight and look under it you can see it has a 10 mm bolt holding it in.

Oct 27, 2010 | 1993 Oldsmobile Cutlass Supreme

1 Answer

1996 Oldsmobile Cutlass Ciera Camshaft Position Sensor Location?


What engine ? 2.2 or 3.1 ?

carjplge-vehodbv0pa23wofwmxc14yyi-3-1.png This 3.1 L back center of engine

Jul 22, 2017 | 1996 Oldsmobile Cutlass Ciera

1 Answer

Where is the camshaft position sensor located on a 1996 Oldsmobile cutlass supreme


the sensor is located behind the power steering pump the plug is on the front left side of motor red and green wires trace it to the sensor behind the power steering pump 8mm bolt holds sensor in and tough to pry out sometime .....

Oct 24, 2009 | 1996 Oldsmobile Cutlass Supreme Coupe

1 Answer

Wher is located the hazard signal flasher on a 1997 oldsmobile cutlass supreme


Under the drivers side of the dash. There may be a plastic cover you have to remove to see it.

May 07, 2009 | 1997 Oldsmobile Cutlass Supreme

1 Answer

Where is the camshaft position sensor located? I have a 93 Cutlass Supreme, I've replaced the fuel filter, fuel pump, and crankshaft sensor. It will not start. It ran briefly, but died and will not start...


it is located at rear of engine neer the firewall you will need to rotate the engine forward under the cylander closest to the drivers side it takes a 10 mm socet to remove it and its a little tricky

Mar 13, 2009 | 1993 Oldsmobile Cutlass Supreme

1 Answer

1997 Oldsmobile Cutless-Oxygen Sensor


If you have the 3100 engine your oxygen sensor is located in the exchaust manifold towards the firewall.

Jan 31, 2009 | 1997 Oldsmobile Cutlass Supreme

1 Answer

Cant find throttle sensor on 1997 Oldsmobile Cutlass Supreme


most likely to be a idle air control sensor, just before throttle body,

Jan 28, 2009 | 1997 Oldsmobile Cutlass Supreme

Not finding what you are looking for?
1997 Oldsmobile Cutlass Supreme Logo

Related Topics:

703 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...