Question about Mazda Protege

1 Answer

How do i take altenater off? - Protege Mazda Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 11,896 Answers

Disconnect the negative battery cable. This unplug the wire harness and then remove the cable that goes from altenator to the battery. Then remove the two bolts holding on the altenator.
When you are replacing the altenator, you can pry it in place to put the bolts back in or use tensioner pulley which moves to allow slack in the belt to place back on the altenator.

Posted on Aug 26, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Intermitant charging 10 to 14 volts with check engine light on


Regulator is in the alternator. Test the output terminal (where the wire bolts on) on the back of the alternator to see if the voltage is right. If not, get a new one, they're cheap. (relatively speaking - $50-$200) P.S. car must be running, watch out for those belts!

Jul 26, 2012 | 1993 Jeep Grand Cherokee

1 Answer

I got a new battery and altenater car still wont hold a charge. Whut can it be?


make sure cables are on tight, if not that u need new altenater

May 29, 2012 | 1991 Honda Accord

1 Answer

Tighten alternater belt


Loosen the altenater and use a prying bar to tighten the belt by pushing the altnater so as to tighten the belt. while holding altenater in place tighten bolts back tight. Belt should be tight when finished.

Feb 25, 2011 | 1994 Nissan Altima

2 Answers

Battery light is on...alternator showing low voltage


I never condem an altenater till I have the battery at full voltage.Make sure the battery hasa good 30 minute slow charge then load test it.If it is good most likely bad altenater.

Feb 18, 2011 | 1992 Oldsmobile Ninety Eight

2 Answers

2003 grand am 2.2 wire from altenater does it go


RED WIRES GOES TO BATTERY POSITIVE CABLE FIRST THATS THE ALTERNATOR FEED.THEN RED WIRE GOES TO A FUSE LINK THEN THE STARTER.YOUR POSITIVE BATTERY CABLE HAS SMALL RED WIRE IT GOES TO ALTERNATOR THEN THE LARGE RED CABLE GOES TO STARTER SOLENOID POS. TERMINAL.

May 06, 2010 | 2003 Pontiac Grand Am

1 Answer

Discharging


replace the drive belt and if you have a keypad on the drivers door and it has been used alot they get shorts in them and will drain the battery so have that tested as well

Jan 18, 2009 | 1998 Ford Expedition

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...