Question about 1988 Chevrolet S-10

1 Answer

How do I fix my 1988 S10 Pickup interior roof? I am currently using aligator clips to keep the lining attached to the hardboard but the hardboard is cracking and falling down also

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Chevrolet Master
  • 2,050 Answers

Spray adhesive, but you will need to remove the entire headliner, then the fabric to re-glue it.

Posted on Aug 26, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

1985 Dodge Power RAM 50, Head liner question.

The fabric and foam are one piece, it is then glued to the cardboard backing and that just site in the roof, no attachment needed.

Dec 01, 2016 | Dodge Cars & Trucks

1 Answer

1988 chevy s10 extended cab 4x4 pickup what side is the fuel filter on driver side or somewhere else?

I'm not sure about the S-10 but most of the GM line has the filter on the drivers side along the inside of the frame and usually back by the axle.

May 06, 2015 | 1988 Chevrolet S-10

1 Answer

Which fuse is for cargo light on a 1988 Chevy s10 pickup?

The cargo light is tied to the interior/dome lights. If you have a dome light then the bulb is bad or it has a broken wire. If not, then check the dome light fuse. In the fuse panel under the dash.

Nov 08, 2014 | 1988 Chevrolet S-10

1 Answer

Wiring/reverse camera

the covers inside we called cards.
they are hardboard with vinyl covering. door cards, or wall cars. etc.
so on most cars, you start low and pull to allow the spring clips to pop
and release.
if not clear, the FSM covers all this, step by step.

Dec 28, 2013 | 2008 Honda Civic

1 Answer

Need new clips for 1988 cadillac sliding panel on sun roof

Local or internet Body Supply Wholesalers

If you order from a dealer they are too expensive

You could try a salvage yard but not many are
stored & get munched

Auto Upholstry Shop

Mar 07, 2013 | Cars & Trucks

1 Answer

How do you take door panel of to get to the window unit

If your car you are working on is reflective of your nickname.. 68 Camaro..

First do yourself a favor and buy a cheap set of interior panel tools. cost you about five to ten dollars.. or you can use a thin stiff prying tool .. The interior panel is a cardboard/hardboard and due to age can crack or break. It has a series of spring clips that pop into corrosponding holes in the door. The obvious needs to be removed.. window crank, door release and arm rest before you begin prying around to locate these clips.

Make sure you are as close to the clips as possible before prying them out.. otherwise they will rupture out of the hardboard and you will need to patch that as best you can.. you may need to buy a few new clips at a local parts store as sometimes the old ones break. When you get the door panel free around the edges/both sides and the bottom.. if I remember right you may need to pop it upwards to free it from the top.

Best of luck to you

Mar 31, 2011 | 1997 Chevrolet Camaro

1 Answer

Where is the fuel pump fuse on a 1989 chevy s10 pickup?

Fuses for the engine or exterior items are under the hood in a little black plastic box.

Fuses for the interior items are under the dash, up above the driver's left foot.

In either case, the fuse diagrams should be on the inside of the fuse cover.

Jun 09, 2009 | 1988 Chevrolet S-10

1 Answer

1988 Chevy S10 Durango Pickup, Won't start will fire

sounds like ignition module inside of distributor cap under distributor rotor button.these do go bad and can easily be replaced.strong suspicion from your details that this is the culprit.

May 09, 2009 | 1988 Chevrolet S-10

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

120 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides