Question about 1993 Chevrolet Corvette

1 Answer

New sensors in tires an ltpws is still coming on. 1990 corvette

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Chevrolet Master
  • 75,797 Answers

This system can be disabled, since these early systems are a real pain to calibrate and VERY expensive to repair have the dealer hook up a scanner and disable the TPMS (tire pressure monitor system)

Posted on Aug 26, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have power to my 1990 corvette but won't come on


Is it an aftermarket radio??? Normally they have a 5A fuse on the back of the unit itself, or in line of the radio's power wire.

Sep 17, 2014 | 1990 Chevrolet Corvette

1 Answer

Why the service LTPWS light stay on on my 1994 corvette LT-1


You need to reset the low tire pressure fault waring, this can be a defective sensor. Read the procedure below.
Replace sensors as required.
Clear DTCs by grounding DLC (under dash in front of driver) terminal 6 to 5, three times in ten seconds.
Receiver/control module will confirm that its memory has been cleared by illuminating both the "L0W/FLAT TIRE" and "SERVICE LTPWS" lamps at the same time. Both lamps will remain ON until the ignition is turned to the OFF position and then back to "ON".

RF sensor MUST be color code BLUE.
If you still get codes, read out the DTCs by connecting DLC terminal 6 to 5 to flash LTPWS. Look for 23, 33, 43, 53 or 24, 34, 44, 54. Right front is LOW TIRE DTC 53 and WHEEL SENSOR DTC 54.

All codes will be preceded with DTC 12. DTC 99 is possible receiver fault.

Nov 03, 2011 | 1994 Chevrolet Corvette

1 Answer

Squeak at left rear wheel due too loose axle spindle nut. What is recommended torque setting for the spindle nut on 1990 corvette conv.


With an assistant depressing the brake pedal to prevent the wheel from turning, tighten the spindle nut to 164 ft. lbs. (223 Nm). The vehicle should not rest on the tires or move until the spindle nut is tightened.

Apr 23, 2010 | 1990 Chevrolet Corvette

1 Answer

What does service LTPWS mean? It's on the dash lights of my 1993 corvette. Thank you!


its a LOW TIRE PRESSURE WARNING SYSTEM is ran buy a sensor in each rim and a modual under the dash....

Mar 21, 2010 | 1993 Chevrolet Corvette

3 Answers

1990 vette stalls after 10-15 min. please help!!


38 lbs is not enough fuel pressure. replace the fuel pump

Mar 15, 2010 | 1990 Chevrolet Corvette

1 Answer

I just read the diagnostic codes on my 1990 corvette. I have two codes showing on the digital speedometer A Module 1 (CCM) Code C12 A Module 4 (ECM) Code H34 What do they mean? Thanks for your help!


Code 34 has to do with your MAP sensor I believe from what I am reading. I don't know a lot about corvettes but it says MAP sensor voltage low. The C12 code I see is a normal code set dealing with no reference pulses being received by control module. In other words with the engine not running. It has to do with No RPM reference pulse.

Sep 08, 2009 | 1990 Chevrolet Corvette

1 Answer

Cannot find relay center in 1990 corvette


check the low side switch located on the ac receiver drier for 12 volts if so jump it with a paper clip if the compressor comes on then the relay is good if not the relay is in the fuse junction box under the hood.Most likely the pressure sensor.

May 23, 2009 | 1990 Chevrolet Corvette

1 Answer

Sys light comming on


SYS means that there is a malfunction and that it's registered in the car's computer. You need to have the system tested for fault codes.

Apr 02, 2017 | 1992 Chevrolet Corvette

1 Answer

Speed sensor on 1990 corvette


Is it the 5.7 L? It's mounted on the transmission. countrycurt0

Oct 10, 2008 | 1990 Chevrolet Corvette

1 Answer

Corvette 1990 5.7L Slow Idle Automatic


i had almost the same problem i changed my fuel pump and fuel filter and it worked u mite try that first.

Jun 25, 2008 | 1990 Chevrolet Corvette

Not finding what you are looking for?
1993 Chevrolet Corvette Logo

Related Topics:

244 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...