Question about 1995 Lexus ES 300

Open Question

Replace egr valve on 1995 lexus es300 - 1995 Lexus ES 300

Posted by on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: can't find the thermostat

the thermostat is located on the drivers side above the starter at the end of the bottom radiator hose on the side of the engine block. i had a hard time getting info also and finally five minutes ago just got mine off. hope this will be of some help to you. now i have to go put on the new one. good luck!!

Posted on May 09, 2009

  • 240 Answers

SOURCE: Where is the expansion valve on a 95 Lexus es300

It is attached to the back wall of evaporator. You have to remove the glove compartment, blower unit and evaporator to get access to the expansion valve.

Posted on Jul 04, 2009

  • 2 Answers

SOURCE: 1996 Lexus ES300 replacing starter

the starter is in the wright side of the motor under the cruis controls. remove the black cover and youll see it....

Posted on Nov 12, 2009

  • 5081 Answers

SOURCE: need to replace thermostat but not sure where it

Follow the lower hose up to the water pump where there is a housing for the thermostat. To remove this you will first, want to take the front right tire off then the dust guard for it; the thermostat housing should now be viseable. Then you will want to take the plastic windshield washer, and engine coolant reserviors off to make the job easier. Next take the bottom rad. hose off the water pump(where it goes to, from the radiator). then struggle for awhile with taking the three nuts that hold the thermostat housing together (a wobbler bit on a socket wrench can make this job easier). Once these are off you can unplug electric plug on top of the housing, pull that part of the housing off and there the thermostat sits in all of its evasive gloriousness waitng for you .

Posted on Nov 16, 2009

  • 17970 Answers

SOURCE: How to replace egr valve on 1995 crown vic 4.6.

On 1995 Crown Victoria the EGR valve is located at the rear of the engine compartment. While the attaching bolts can be gotten out with a little bit of a problem the egr tube that atteches the EGR valve to the right exhaust manifold is a pain. It is possible to do though. Here are the removal and installation instructions. If you are sure that the EGR valve is the reason for any check engine light then you can remove the battery cable for about five minutes to reset the light, but if the light is on for a differant reason then you just got rid of the code plus any freeze frame data that a shop could have used to diagnose the problem.

Check this procedure about REMOVAL & INSTALLATION...

PFED Sensor
See Figures 9, 10, 11 and 12

Fig. 9: Detach the connector for the DPFE sensor

Fig. 10: Matchmark and remove the vacuum hoses for the DPFE sensor and ...

Fig. 11: ... remove the retaining nuts from the DPFE sensor and ...

Fig. 12: ... remove the DPFE sensor from the intake manifold

  1. Disconnect the negative battery cable.
  2. Label and disconnect the wiring harness from the DPFE sensor.
  3. Label and disconnect the vacuum hoses.
  4. Remove the mounting screws and remove the DPFE sensor.
To install:
  1. Position the DPFE sensor and tighten the mounting screws.
  2. Attach all necessary hoses and wiring to the sensor.
  3. Connect the negative battery cable.

EGR Valve Control Solenoid
See Figures 13 through 17

Fig. 13: Detach the connector for the EVR solenoid

Fig. 14: Match mark the vacuum hoses for the EVR solenoid and ...

Fig. 15: ... remove the vacuum hoses from the EVR solenoid

Fig. 16: Remove the retaining nut for the solenoid and ...

Fig. 17: ... remove the solenoid from the intake manifold
  1. Disconnect the negative battery cable.
  2. Label and detach the vacuum hoses from the EVR solenoid.
  3. Detach the electrical connector from the solenoid.
  4. Remove the retaining hardware, and remove the solenoid.
To install:
  1. Position the solenoid and install the retaining hardware.
  2. Attach the main emission vacuum control connector and the wiring harness connector to the EVR solenoid.
  3. Connect the negative battery cable.


Posted on Jul 16, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do you replace the Evaporation Control Valve and the ERG Valve on a 1997 Lexus ES300?

Anon, disconnect vacuum lines,wires, etc. and unbolt EGR from intake shown in 4th video link. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Toyota Po441 P0446 EVAP Vacuum Switching Valve VSV Testing and Canister...
How To Test and Replace EVAP Canister Vent Control Valve P0446
1997 Lexus ES300 Evaporation Control Valve Google Search
OBD II Trouble Code P0401 Insufficient EGR Flow
How to Fix P0401 on 1996 Toyota Avalon Testing The EGR Modulator Valve

Jun 15, 2016 | Lexus Cars & Trucks

1 Answer

1992 lexus es300 will **** and buck if stopped in

old age--trans probly needs service or wearing--also inspect vacuum hoses in ngine-things like egr valve hav hidden leaks

Oct 19, 2013 | Cars & Trucks

1 Answer

1995 lexus es300 fuse box diagram

On this website, you find fuse box diagram and description for Lexus ES300 (1994 - 1995)

Lexus ES300 1994 1995 fuse box diagram Auto Genius

Jan 12, 2012 | 1995 Lexus ES 300

1 Answer

1994 lexus es 300 fuse box diagram

On this website, you find fuse box diagram and description Lexus ES300 (1994 - 1995)

Lexus ES300 1994 1995 fuse box diagram Auto Genius

May 16, 2011 | Lexus ES 300 Cars & Trucks

1 Answer

Where is the EGR position sensor located on a 1995 es300 lexus?


It is located Rear Center Of the Engine.

Good Luck

Dec 13, 2009 | 1995 Lexus ES 300

1 Answer

How do I change the headlampo on a 1995 lexus es300

I was able to release the headlamp bulb on the 1995 Lexus es300 by removing the rubber cover and releasing a pin that keep the bulb in place. I willhave to purchase a HELO replacement bulb, part number
SKU: HEL.1637160.11701

Oct 08, 2009 | 1995 Lexus ES 300

1 Answer

Cold start missfire

could be a cold start issue. there is a water temp sensor near the thermostat. when you start your engine first for the day it will show the engine to be cold and therefore the computer will do a 'cold start', meaning using more fuel. but this should throw a computer code. if you are not getting any codes from the computer then check for a vacuum leak. like the EGR vacuum line for starters. the egr should be closed when the engine is cold and open as the engine warms up.

Mar 23, 2009 | 1995 Lexus ES 300

1 Answer

Lexus es300 timing belt change & water pump

replace timing belt on es300 1995

Mar 20, 2009 | 1995 Lexus ES 300

2 Answers

1995 lexus es300

Not the oil pump, the most likely cause is the intake and exhaust valve seals, this accounts for the smoke on start up

Sep 22, 2008 | 1995 Lexus ES 300

Not finding what you are looking for?
1995 Lexus ES 300 Logo

Related Topics:

341 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts


Level 3 Expert

80417 Answers


Level 3 Expert

918 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides