Question about 2002 Audi A6

1 Answer

How much to replace rear brakes and install a fuel filter?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Audi Master
  • 14,036 Answers

CHECK AROUND AND GET A PRICE CHECK. AUDI DEALERSHIP PROBABLY $300.00 BUY BRAKE SHOES AND FUEL FILTER GET A INDEPENDANT GARAGE TO DO THE JOB. YOU MIGHT PAY AT LEAST $200.00

Posted on Aug 26, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mitsubishi mirage 1995 50,000maitenance requirements


MAINTENANCE INTERVALS FOR 52500 MILES IS ENGINE OIL AND FILTER CHANGE.TIMING BELT CHANGE IS 60000 MILES INTERVAL. MOST OF ENGINE TUNE UP IS DUE AT 60000 MILES INTERVAL.YOU NEED TO REPLACE TIMING BELT, REPLACE ENGINE COOLANT, REPLACE SPARK PLUGS,REPLACE IGNITION CABLES. REPLACE ENGINE OIL AND FILTER. YOU NEED TO SERVICE AND INSPECT ALL THESE ITEMS, AUTOMATIC TRANSMISSION FLUID AND FILTER,BRAKE HOSES, BRAKE PADS,DRIVE SHAFT BOOTS,VALVE CLEARANCE,BALL JOINTS AND STEERING LINKAGE SEALS,DRIVE BELTS,EXHAUST SYSTEM,FUEL HOSES,MANUAL TRANSAXLE OIL,REAR DRUM BRAKE LININGS AND REAR WHEEL CYLINDERS.

May 21, 2011 | 1995 Mitsubishi Mirage

1 Answer

How do you replace a 2001 Mazda 626 Fuel Filter


Fuel Filter On all models except the Millenia, the fuel filter is attached to a bracket located in the left rear of the engine compartment, next to or beneath the brake master cylinder fluid reservoir. On the Millenia, the fuel filter is located beneath an access cover in the trunk. Access to the cover is achieved by removing the trunk mat to expose the cover.
---
REMOVAL & INSTALLATION Except Millenia
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Properly relieve the fuel system pressure.
  3. Remove or disconnect the following:
    • Negative battery cable Fig. 1: Exploded view of a common fuel filter and related components 7923mg68.gif

    • Air intake hose and/or filter housing, if necessary
    • Fuel line clamps, if equipped
    • Fuel lines from the filter and plug the openings
    • Filter clamp bolt/nut by loosening them.
    • Fuel filter from its mounting bracket
    NOTE: Note the direction of the flow arrow on the filter so the replacement filter can be installed in the correct position. To install:
  4. Install or connect the following:
    • Fuel filter in its mounting bracket, making sure the flow arrow is pointing in the proper direction
    • Fuel lines to the fuel filter
    • Fuel line clamps, if equipped
    • Air intake hose and/or filter housing, if removed
    • Negative battery cable
  5. Pressurize the fuel system and check all connections for leaks.
Millenia
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Insure the ignition switch is OFF.
  3. Relieve the fuel system pressure.
  4. Remove or disconnect the following:
    • Negative battery cable
    • Trunk mat
    • Service hole cover
    • Fuel lines from both ends of the fuel filter
    • Fuel filter and bracket
    • Fuel filter from the mounting bracket.
    To install:
  5. Install or connect the following:
    • Filter in the bracket. Tighten the nut to 70-95 inch lbs. (8-11 Nm).
    • Fuel lines to the filter
    • Service hole cover
    • Trunk mat
    • Negative battery cable
  6. Run the engine and check for any fuel leaks.
prev.gif next.gif

Oct 17, 2010 | 2001 Mazda 626

2 Answers

Need to press on the gas more to get the speed i used to; engine noise, lower fuel average, need to press brake pedal further down to stop car; why?


COULD BE DIRTY FUEL INJECTORS OR STOPPED UP FUEL PUMP FILTER WHICH IS ON THE FUEL PUMP.EXCESSIVE BRAKE PEDAL TRAVEL CAN BE BRAKE POWER BOOSTER NOT GETTING ENOUGH ENGINE VACCUM OR BRAKE BOOSTER CHECK VALVE OR BRAKE BOOSTER FAULTY.YOU COULD HAVE LOW BRAKE FLUID LEVEL IN MASTER CYLINDER.OR NEW BRAKE SHOES HAS NOT BROKE IN.

Jul 11, 2010 | 2008 Toyota Camry

1 Answer

Hello, I was just wondering how to change the fuel filter on a 2005 mazda 6 v6?


Mazda Car 2005-06 Repair Guide
Fuel Filter Removal & Installation

The fuel filter on most Mazda cars can be located on a bracket in the left rear of the engine compartment, next to or beneath the brake master cylinder fluid reservoir or as part of the fuel pump assembly.

The filter on Mazda3 models is part of the fuel pump assembly.
The fuel filter is part of the pump assembly. Once the fuel pump is removed, remove the filter retainer and filter. refer to the fuel pump procedure or removal and installation.

Hope helps with this (remember rated this help) Good luck.

Jan 12, 2010 | 2005 Mazda 6

3 Answers

Where is it located? The fuel filter. My 2003 KIA sorrento will not accelerate up hills. Either hwy or city. On level ground it is fine. Is the fuel filter possible my proble. AGain if so, where is it...


For Kia Sorento 2003-2005 the fuel filter is located inside the fuel tank and is replaced with the fuel pump as an assembly.

Fuel Pump - Removal & Installation
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:
    Rear seat Access cover Fuel pump electrical connector
  3. Relieve the fuel system pressure.
    Fuel lines Fuel pump and filter assembly
To install:
  1. Install or connect the following:
    Fuel pump and filter assembly Fuel lines Fuel pump electrical connector Access cover Rear seat
  2. Start the engine and check for leaks.

Hope helped with this (remember rated this help) Good luck.

Nov 19, 2009 | 2003 Kia Sorento

2 Answers

I need to change the fuel filter. where is it located. do i need special tools ?


The fuel filter on most Mazda cars can be located on a bracket in the left rear of the engine compartment, next to or beneath the brake master cylinder fluid reservoir or as part of the fuel pump assembly.

On the Millenia, the fuel filter is located beneath an access cover in the trunk. Access to the cover is achieved by removing the trunk mat to expose the cover.


The filter on Mazda 3 models is part of the fuel pump assembly.


The fuel filter on all Mazda cars can be located on a bracket in the left rear of the engine compartment, next to or beneath the brake master cylinder fluid reservoir or as part of the fuel pump assembly.



How to Replace a Fuel Filter
Parts:
  1. Fuel Filter - $175.45

Tools:
  1. 3/8 in. drive ratchet - $7.55
  2. Hose pincher - $4.07
  3. Flare nut wrench - $5.53
  4. Flat Head scredriver - $3.14
  5. Socket Set
Steps:
Open the hood and locate the fuel filter. If the fuel filter is not in the engine compartment, follow the fuel line from the tank until the fuel filter is located.

1. Fuel filter in engine compartmentf9b91e0.jpg
Tip: Safety Tip:Always wear safety glasses when working on your vehicle. Wear other personal protective equipment (PPE) when necessary, for example latex gloves or safety shoes.

  • 2. If the fuel filter has a clear case, inspect the filter element for dirt.

  • 3. If the fuel filter case is not see-through, remove it from the fuel line. Drain the fuel from the filter into a container and inspect the condition of the fuel.
  • Tip: Caution: Before removing fuel lines or fuel related parts, make sure that the fuel pressure is relieved from the vehicle fuel system. To relieve the pressure in fuel injected systems, remove the fuel pump fuse and run the engine

  • 4. Install the new fuel filter making sure that the flow is in the correct direction. The arrow on the fuel filter is the direction of flow from the tank to the engine.
  • 5. Secure the lines back onto the fuel filter. If applicable, reinstall the fuel pump fuse.
  • 6. Start the engine and check for fuel leaks.
  • 7. Test drive the vehicle to check for a rough running engine, hesitation, or lack of power.

  • Good luck (remember rated this help).

Nov 09, 2009 | 2004 Mazda 6

1 Answer

Fuel filter location/replacement My car is cutting out at 4000 RPM


2006 Mazda MX-5 Miata 2.0L MFI DOHC 4cyl
Mazda Car 2005-06 Repair Guide - Removal & Installation

The fuel filter on most Mazda cars can be located on a bracket in the left rear of the engine compartment, next to or beneath the brake master cylinder fluid reservoir or as part of the fuel pump assembly.

The filter on Mazda3 models is part of the fuel pump assembly.

The fuel filter is part of the pump assembly. Once the fuel pump is removed, remove the filter retainer and filter. refer to the fuel pump procedure or removal and installation.

I hope help you. Good luck.

Oct 12, 2009 | 2006 Mazda Miata

2 Answers

Changed Fuel Filter with full service but engine not turning on


hello,if your old fuel filter is not dirty,install your fuel filter,sometimes fuel filter is defect even it"s new,hoping there is no fuel leak during your replacement of filter,ty

Apr 20, 2009 | Mercedes-Benz E320 Cars & Trucks

1 Answer

Basic service


Here are detailed instructions on the location, removal, and re-installation of your fuel filter. Hope it helps and have a great day!

REMOVAL & INSTALLATION
Carbureted Engines
These vehicles use two replaceable fuel filters. A small one is in the fuel line under the hood; a larger one is located at the rear, just inboard of the left rear wheel.
Whenever the filter(s) are replaced, take great care to avoid the entry of dirt into the lines. Also, pay attention to the correct installation position. It is possible to install the filter backwards.
FRONT
See Figure 2
  1. If applicable, disengage the filter or hose from its retaining clip.
  2. Using two fuel line clamps, pinch off both fuel lines. Take care not to crush the lines; just clamp them shut.
If the fuel hoses are hard or cracked, it is necessary to replace them.
0900c1528005f267.jpgFig. 2: Front fuel filter used on carbureted engines
  1. Loosen the fuel line clamps and slide them back.
  2. Using a twisting motion, remove the fuel lines from the filter.
  3. To install, use a new fuel filter and reverse the removal procedures. Start the engine and check for leaks. Correct any leaks immediately.
REAR
See Figures 3, 4, 5 and 6
  1. Raise and safely support the rear of the vehicle. Remove the left rear wheel.
  2. Remove the bolts securing the filter and its basket to the fuel tank.
0900c1528005f268.jpgFig. 3: Remove the bolts securing the filter and its basket to the fuel tank ...
  1. Push the fuel filter retaining tab and release it from the basket.
0900c1528005f269.jpgFig. 4: ... then release the basket from the filter
  1. Using two fuel line clamps, pinch off both fuel lines. Take care not to crush the lines; just clamp them shut.
0900c1528005f26a.jpgFig. 5: Clamp the fuel lines shut. If the lines are hard, cracked or brittle, they must be replacedIf the fuel hoses are hard or cracked, it is necessary to replace them.
  1. Loosen the fuel line clamps and slide them back.
  2. Using a twisting motion, pull the fuel lines from the fuel filter; remove the filter.
0900c1528005f26b.jpgFig. 6: After sliding the retaining clamps back, the filter can be removed from the linesTo install:
  1. Use a new filter and reverse the removal procedures.
  2. Make certain the retaining tabs are engaged when the filter is installed in the holder. Tighten the bolts until snug.
  3. Install the left rear wheel. Lower the car to the ground.
  4. Start the engine and check for leaks. Correct any leaks immediately.
Fuel Injected Engines
See Figures 7, 8, 9, 10, 11 and 12
The canister fuel filter is located in the engine compartment. When buying the new filter, also buy new washers for the banjo bolts and the service bolt. Failure to replace these washers invites high-pressure fuel leaks. Replacing the washers is required, not recommended.
  1. Disconnect the negative battery terminal.
  2. The fuel system is under pressure. Release pressure slowly and contain spillage. Observe "no smoking/no open flame" precautions. Have a Class B-C (dry powder) fire extinguisher within arm's reach at all times.
  3. Disconnect the banjo bolts and/or threaded fuel line fitting from the fuel filter. Use of a flare nut or line wrench is recommended for disconnecting and attaching this fitting.
0900c1528005f26c.jpgFig. 7: Fuel filter used on fuel injected Accords through 1989 0900c1528005f26d.jpgFig. 8: Fuel filter on 1990-93 fuel injected Accords 0900c1528005f26e.jpgFig. 9: Fuel filter used on fuel injected Preludes through 1991
  1. Loosen the fuel filter clamp bolt, then remove the filter.
To install:
  1. Install the new filter and secure the clamp bolt.
  2. The upper and lower washers on each banjo bolt and the washer on the service bolt MUST be replaced whenever the bolts are loosened. Install the washers and banjo bolts. Tighten the banjo bolts to 16 ft. lbs. (22 Nm) on all models except 1992-95 Preludes. On these models, tighten the bolt to 20 ft. lbs. (28 Nm). If applicable, tighten the threaded fuel line fitting to 27 ft. lbs. (37 Nm).
0900c1528005f26f.jpgFig. 10: Fuel filter used on 1992-95 Preludes 0900c1528005f270.jpgFig. 11: Fuel filter used on 1994-95 4-cylinder AccordsIt will be necessary to use a crow's foot attachment on a torque wrench to properly tighten the threaded fuel line fitting.
  1. Tighten the service bolt to 9 ft. lbs. (12 Nm).
  2. Start the engine and check for leaks. The engine may crank longer than normal until full fuel pressure is developed. Correct any leaks immediately.
0900c1528005f271.jpgFig. 12: V-6 Accord fuel filter

Nov 23, 2008 | 1985 Honda Accord

2 Answers

I just got my front brakes replaced on my 2000 Toyota Camry. It has less than 80,000 miles on it. The mechanic said that there had been only 1/32nd" left on the front, but the back brakes were fine....


everything the mechanic suggested is right on target. Over time you do not realize that the ride of your car has deteriorated until you put on the new struts and the alignment is a must after the replacement of those struts. As far as the back brakes being good versus the front being worn out, the front brakes take a lot more abuse than the rears do to eight transfer upon braking.

Nov 18, 2008 | 2000 Toyota Camry

Not finding what you are looking for?
2002 Audi A6 Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

74896 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14184 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...