Question about 1992 Mitsubishi Mighty Max

1 Answer

REPLACED THE DISTRIBUTOR STILL WONT START CRANKS OVER FINE .IT FEELS LIKE THERE IS NO SPARK

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Contributor
  • 435 Answers

Before you crank,be sure if the primary current flow to the distributor,if not it will never spark.

Posted on Aug 27, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Engine cranks has spark at distributor but wont start.


standing for a while could be stale fuel
efi or carby
is it a points or electronic module distributor
could be coil, or plug, leads points

Jul 16, 2016 | Cars & Trucks

1 Answer

Had motor replaced in mazda 6. now it wont start. ran fine from shop to home. started up then died and wont start. cranks with no fire up. has gas. fuel pump primes when turned on...


Pull out the spark plugs from the engine and see if spark comes from the distributor......if not replace distributor...costs around $280

Feb 25, 2015 | Mazda 6 Cars & Trucks

1 Answer

Truck wont start


Check for spark at the distributor if no spark check or replace coil pack. also check to see distributor is turning while engine cranking, if not, possible worn out or broken gear tooth on shaft inside engine.
if distributor turns, check for burnt or worn out points and/or contacts on distributor cap.

Dec 27, 2013 | 1986 Ford Ranger 2WD

1 Answer

I have a 2003 is 300 coming down from south padfre it overheadted , i replaced radiator spark plugs . now car crank but it wont start it feels like it does not have any compression at all


When car overheated the steam heats the distributor same time remove distributor cup and check if is clean and dry, 2nd remove spark plugs and give compression test check your coil two stay dry and clean.

Sep 12, 2012 | 1994 Lexus GS 300

1 Answer

I try turning the car on but it wont start. I can hear the starter cranking so I know it can't be that. Checked battery and alternator and both were fine. Checked the spark plugs, they were ok but it...


Pull out the coil wire from the distributor and see if it is sparking. If there is no spark, the coil is dead and it needs to be replaced.

Mar 24, 2011 | 1997 Honda CR-V

1 Answer

Im getting fuel, spark, and comprestion. I had a hard time getting the vehicle timed, but feel confedent that it is correct now. still wont start.


could be 180 degrees off wth distributor,check crank sensor,try spraying starting fluid in air box to see if it will crank,if so fuel problem

Jan 01, 2011 | 1996 Oldsmobile Bravada

1 Answer

91 honda accord wont crank


There is a sensor under the left hand side of the dash that would not allow it to start, provided that you have replaced the electronic spark module inside the distributor first, which is what it sounds like it would be, When you say you replaced the distributor I assume you replaced it complete!

Jun 12, 2010 | 1991 Honda Accord

3 Answers

97 nissan pathfinder cranks but wont start no spark


Did you try looking through the fuse panels or relays?

Apr 09, 2009 | 1997 Nissan Pathfinder

1 Answer

My 1987 300zx cranks but wont start.


I had the same problem last year mine turned out to be a crank sensor I don't know if that is your problem for sure mine wouldn't send any spark from the coil to the spark plug replaced crank sensor inside distributor and fired right up the dealership called it a cam sensor my book called it a crank sensor either way its in the distributor

Dec 16, 2008 | 1987 Nissan 300ZX

Not finding what you are looking for?
1992 Mitsubishi Mighty Max Logo

Related Topics:

154 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...