Question about 2000 Pontiac Montana

1 Answer

When starting my 2000 Montana the starter sounds like it is being ground as if the vehicle were already started.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 81 Answers

Selinoid is bad, replace starter cost about 200 for part, starter is attached to side of transmission. access under van

Posted on Aug 26, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 Pontiac Montana wont start, no power to vehicle


I suspect an ignition switch problem, you need to check to see if when you try to start it if there is power to the signal wire at the starter. If there isn't, check the same wire at the ignition switch, if there still is no power, check to make sure the grounds from the firewall are secure and they have near zero resistance between the firewall and the negative battery post. Check to make sure there is power getting to the ignition switch, if there is none, then you have a broken fusible link under the hood

Apr 21, 2013 | 2000 Pontiac Montana

1 Answer

2000 pontiac montana Occasionaly, when turning the key to start, it will be dead dash lights will illuminate, but no life to engine to start it What's up?


check starter wiring for loose nuts, bad connetion. n what not. clean up terminals if needed n see if it turns over if not. check for power coming frm the yellow wire, or the smaller one. with the key held in start position, in no power you will need a starter solinoid. if you do have power go grab a starter n put it in,

Dec 16, 2010 | 2000 Pontiac Montana

2 Answers

How much work is involved to install a car starter on a 2000 Pontiac Montana?


un-plug the ground side of the battery then

jack up vehicle and support it with stands.the starter is on the front of the engine,there are two bolts that hold the starter up.you will need a 15mm socket to remove the bolts. you will also need a 13mm socket to remove the power wire off the back of the starter.then there is one more wire you will need to remove and its an 8mm.just do the reverse to install it
takes about 30 min.if you have never taken one off may take an hr.

Dec 07, 2010 | 2000 Pontiac Montana

1 Answer

2002 pontiac montana wont start battery tested good vehicle completely dead no lights, radio, etc. Ground connection good termenals clean. Would alternator be the next thing to try???


no Alternator wont stop it from starting or rolling over as long as good battery...try connections on starter..that would be what i looked for first

Mar 05, 2010 | 2002 Pontiac Montana

2 Answers

Vehicle will not start, no power to starter


Continue tracing back to the ignition/starter switch and associated fuses.

Oct 21, 2009 | 2006 Pontiac Montana

2 Answers

Car won't start. Already replaced battery and


Replace the starter relay,It is located in the fuse box under the hood

Jul 30, 2009 | 1996 Chevrolet Cavalier

1 Answer

Pontiac Montana starting problem


All 4 power wires go together on the large center stud on the solenoid.
The purple wire goes on the small stud.
The purple wire supplys the trigger signal when the key is turned to the start position.Since your solenoid is clicking when the key is turned to start this is working properly.
I would check battery connections and then check power connections on solenoid again.Make sure all connections are clean and tight.

Nov 06, 2008 | 2000 Pontiac Montana

4 Answers

Battery good, wont turn over, just a click when try to start


it is most likley starter relay or starter.with vehicle in park and e-brake on have someone tap on the starter with hammer while your trying to start.if starter starts to crank then you know the starter is on the way out.if starter does not crank it may already be shot.srarter relay is on fire wall check power + ground.

Oct 26, 2008 | 2000 Ford F250 Super Duty Crew Cabs

Not finding what you are looking for?
2000 Pontiac Montana Logo

Related Topics:

113 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...