Question about Ford Windstar

1 Answer

Lt. ft. window will not go up or down - Windstar Ford Cars & Trucks

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 3,074 Answers

May be a fuse, the switch or the regulator. I would check all the fuses, if they are good then I would check the switch, the I would remove the door panel. Hope this helps tim

Posted on Aug 25, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Head bolt torque for 3.5 and sequence

Tighten headbolts in three steps, 22 ft lbs--44 ft lbs-- then 140 degrees. I got this info from my database.

Apr 15, 2016 | 2006 Chevrolet Chevrolet Impala LT

2 Answers

3.9l V6. Can I re-torque rear caliper bolts to 26 ft. lbs.?

you could but at this point I would just leave them alone unless there is a problem in the function of the calipers in which case remove and replace the bolts with new bolts as the used bolts will be stretched

Mar 02, 2016 | 2006 Chevrolet Chevrolet Impala LT

1 Answer

2007 dodge Dakota driver window will not go up or down . All the other windows work.

I would try contacting car <a href="">windows in Ottawa</a> to see if they can give you some assistance.

Oct 22, 2013 | Cars & Trucks

1 Answer

What special tools do I need to remove the fuel tank from my 04 F250 for cleaning ?

Anyone special tool, just check this procedure to Removal & Installation
CAUTION Fuel injection systems remain under pressure, even after the engine has been turned OFF. The fuel system pressure must be relieved before disconnecting any fuel lines. Failure to do so may result in fire and/or personal injury.
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    Negative battery cable Fuel pressure Fuel tank skid plate bolts and lower the skid plate. Fuel Fuel tank filler pipe hose from the tank Fuel tank filler pipe vent hose from the tank Fuel lines from the fuel pump Front fuel tank connections Rear Evaporative Emissions (EVAP) hose clamp and the hose Electrical connector from the fuel pump

  3. Support the fuel tank with a jack.
    Fuel tank support strap bolts and the fuel tank straps Fuel tank
To install:
  1. Installation is the reverse of removal. Note the following torques:
    1. Tighten the fuel tank strap bolts to:
      F-150: 35 ft. lbs. (47 Nm) F-250 and F-350 mid-ships tank: 30 ft. lbs. (40 Nm) F-250 and F-350 aft-of-axle tank: 66 ft. lbs. (90 Nm) Mark LT: 35 ft. lbs. (47 Nm)
  2. Tighten the skid plate bolts to:
    F-150: 15 ft. lbs. (20 Nm) F-250 and F-350 mid-ships tank shield: 15 ft. lbs. (20 Nm) F-250 and F-350 aft-of-axle tank cover: 66 ft. lbs. (90 Nm) Mark LT: 15 ft. lbs. (20 Nm)
  3. Connect the negative battery cable.

Hope helps.

Dec 24, 2010 | 2004 Ford F250

1 Answer

What are the torque specs for the rocker arm bolts?

65-75 ft/lbs. Be sure you use the correct tightening sequence, This is important.
< 9 5 1 3 7 <10 6 2 4 8
< indicates front of MOTOR , not front of car

Mar 23, 2010 | Chevrolet Cavalier Cars & Trucks

1 Answer

I am trying to find out the wiring colors and what they are. I am trying to install a cd player in my 94 honda accord but ca't figure out the wire colors to be able to hook up correctly. Need Help!!

yel/red battery(always hot),wht/blue hot w/ignition,red/blk hot w/lighting switch,blk ground,red/grn rt ft +,brn/blk rt ft -,blue/grn lt ft +,gry/blk lt ft -, blue/yel rt rr +,gry/whte rt rr -,red/yel lt rr +, brn/whte lt rr -

Oct 16, 2009 | Honda Accord Cars & Trucks

1 Answer

Windows have stopped working

I have the same issue. their are two things that you can do. One is pricey the other is free. Pricey, you will have to replace you window motor. Around 250 - 300 dollars. Free, and this is what I do. Remove the panel from the door. remove the plastic from the door, on the lower left side of the door, closest to the hinge, you will see the electric motor. While holding the button for the windows in the down position, tap the bottom part of the motor with a hammer or other hard object. What this does is frees up the gearing in the motor, which is more than likely gunked up with filings from the brushes in the motor. I have done this and it has worked for both windows. Hope this helps

May 28, 2009 | 1989 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides