Question about 1996 Isuzu Rodeo

Open Question

How do i replace the alternator belt on a 1996 isuzu rodeo? what do i have to remove to get to the alternator belt?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 84 Answers

SOURCE: replace the alternator on a 97 isuzu rodeo

from Yahoo answers
The alternator is located on the passenger side of the motor at the bottom. There is a bracket attached to the motor and the alternator. You need not take the bracket off to remove the alternator. Two bolts hold the alternator to the bracket. One bolt is on the front top of the alternator and one bolt is located on the bottom front of the alternator. The bottom front bolt is attached to the tension adjustment for the alternator. Loosen the tension screw then remove the bolt going through the tension adjustment. After you loosen the top, front bolt, the alternator should be loose enough to move side to side. Remove the top, front bolt. Now you must disconnect the alternator from the power supply. Behind the alternator is a screw with a wire attached via nut. Remove this wire. Nextly there is a series of wires with a plug on the end. It is plugged into the side of the alternator. Uplug this item. You can also access both of these from the passenger side front tire well. Something to consider is that remanufactured alternators in Rodeo's as well as the Honda Passport (which has the same engine as the Rodeo) do not work and the problem(s) associated with a bad alternator,ie; not charging, no fan blower, battery light and brake light on, still exsist after replacing alternator with reman. Use a factory original alternator if possible. It will cost a little more than a reman but will most likely save you a lot of time and headache!

Hope this helps you out!!
L

Posted on Sep 29, 2008

Ad
pakis
  • 86 Answers

SOURCE: squealing belt

Causes of problem like yours can be:

  1. the alignment of the pulley of your alternator and the alignment of your engine's pulley. you may check it by just looking at it, be sure they are precisely parallel with each other.
  2. The size of the opening of your pulleys, you try to measure it using a caliper, they should have the same mouth size
  3. loose pulleys causing wiggle
  4. rusts on your pulleys
Hope I helped you

Posted on Nov 24, 2008

  • 548 Answers

SOURCE: 1997 Isuzu Rodeo Belt removal

You need to loosen the alternator so the belts become slack. Look for bolts on top and bottom that attach the alternator to a bracket or the engine block. Loosen them and the alternator will move. Since the belts hook to other accessories, you may need to loosen them too. To get them back and the proper tension, you'll need a large screwdriver or pry bar to put tension on them as you tighten the bolts. I suggest you get a Haynes guide for this model that will have photos showing how this is done.

Posted on Jan 11, 2009

  • 9 Answers

SOURCE: 2000 isuzu rodeo removal and installation of serpentine belt

All u need to do is put a wrench on the tention pully and turn it clockwise... this will relive the tention take off the old belt ....put on new one. repeat relive pressure again ...slip it on pully... and relese tention..... done! :)

Posted on Jun 11, 2009

honeymokey
  • 3113 Answers

SOURCE: water pump replacement 96 isuzu rodeo

Remove belt, fan, fan shroud and fan bracket. Remove timing covers, timing belt and water pump. Replace timing belt and the hydraulic tensioner with new ones. I suggest you get a mechanic to do this as you can easly get it out of time. Not an easy job.

Posted on Jul 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace a 1995 2.4 v6 isuzu rodeo alternator belt?


Just do a search on google. (1995 2.4 v-6 Isuzu alternator belt diagram) There are plenty of diagrams showing the belt routing. Put the belt on all the pulleys you can. Take a wrench and pull back the tensioner, slip the last part of the belt over the last pulley. Then, release the tensioner arm and it will tighten up the belt. Turn it over and check it again to be sure it is on straight.

Oct 13, 2014 | 1995 Isuzu Rodeo

1 Answer

How do I replace an alternator in a 1996 v6 isuzu rodeo


I'll confirm what LegendLB said about the remanufactured alternators. I installed a reman into my '96 Isuzu and it did not work. The brake + battery light combo was still on. I haven't installed a new alternator yet, it will arrive in a week.

Jan 31, 2012 | 1996 Isuzu Rodeo

1 Answer

How do I change the alternator belt on my 1996 Rodeo?


u have to loosen up the tension pulley and remove the old belt. then replace the new belt and tighten the the tension pulley again. becareful not to tighten harder or the belt would break.

Mar 01, 2011 | 1996 Isuzu Rodeo

1 Answer

The 2 bolts on the alternator are not going in . How do i line up the screws on a 1998 alternator for isuzu rodeo


put the alternator on first without the belt and alighn as needed to replace the bolts use the belt tentioner to replace the belt or the sliding channel on the alternatonr mounts if there is no tentioner

i hope this helps u with your problem

Nov 12, 2010 | 1998 Isuzu Rodeo

1 Answer

How to remove the alternator on a 2000 isuzu rodeo


It is easiest to place the car on a lift and remove the alternator from the bottom. Disconnect the belt FIRST, then the wiring, and then the bolts mounting the alternator. Installation is the reverse. Make SURE you have the correct alternator for your application. Voltage regulators for the 4 cyl and V-6 were different.

Jun 07, 2010 | 1999 Isuzu Rodeo

2 Answers

Is it necessary to take the timming belt off to replace the water pump on a 1996 isuzu rodeo


3.2L engine, you will have to remove timing belt to replace water pump, your water pump is timing belt driven, I would replace timing belt while in there, good luck, hope this was very helpful.

May 14, 2010 | 1996 Isuzu Rodeo

1 Answer

Water pump replacement 96 isuzu rodeo


Remove belt, fan, fan shroud and fan bracket. Remove timing covers, timing belt and water pump. Replace timing belt and the hydraulic tensioner with new ones. I suggest you get a mechanic to do this as you can easly get it out of time. Not an easy job.

Jul 03, 2009 | 1996 Isuzu Rodeo

1 Answer

1997 Isuzu Rodeo Belt removal


You need to loosen the alternator so the belts become slack. Look for bolts on top and bottom that attach the alternator to a bracket or the engine block. Loosen them and the alternator will move. Since the belts hook to other accessories, you may need to loosen them too. To get them back and the proper tension, you'll need a large screwdriver or pry bar to put tension on them as you tighten the bolts. I suggest you get a Haynes guide for this model that will have photos showing how this is done.

Jan 11, 2009 | 2002 Isuzu Rodeo

1 Answer

97 isuzu rodeo


look carefully as power steering belt has to be removed and A/C if fitted,slacken bolts on power steering pump then find the tensioner bolt and slacken it off and then push pump unit back..Same sort of thing with the A/C pump but i think but cant remember but i sure this one has an idler/tensioner to slacken.

Jan 10, 2009 | 1997 Isuzu Rodeo

2 Answers

Replace the alternator on a 97 isuzu rodeo


from Yahoo answers
The alternator is located on the passenger side of the motor at the bottom. There is a bracket attached to the motor and the alternator. You need not take the bracket off to remove the alternator. Two bolts hold the alternator to the bracket. One bolt is on the front top of the alternator and one bolt is located on the bottom front of the alternator. The bottom front bolt is attached to the tension adjustment for the alternator. Loosen the tension screw then remove the bolt going through the tension adjustment. After you loosen the top, front bolt, the alternator should be loose enough to move side to side. Remove the top, front bolt. Now you must disconnect the alternator from the power supply. Behind the alternator is a screw with a wire attached via nut. Remove this wire. Nextly there is a series of wires with a plug on the end. It is plugged into the side of the alternator. Uplug this item. You can also access both of these from the passenger side front tire well. Something to consider is that remanufactured alternators in Rodeo's as well as the Honda Passport (which has the same engine as the Rodeo) do not work and the problem(s) associated with a bad alternator,ie; not charging, no fan blower, battery light and brake light on, still exsist after replacing alternator with reman. Use a factory original alternator if possible. It will cost a little more than a reman but will most likely save you a lot of time and headache!

Hope this helps you out!!
L

Sep 29, 2008 | 1996 Isuzu Rodeo

Not finding what you are looking for?
1996 Isuzu Rodeo Logo

Related Topics:

672 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...