Question about 1966 Ford Mustang

Open Question

1969 Ford 302 ci motor that runs but shows no oil pressure on a brand new gauge. Even took the fitting out of the side of the block and nothing comes out. Brand new oil pump also. What is up with that?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 4 Answers

SOURCE: oil pressure

Check the oil pressure switch!

Posted on Jun 14, 2008

  • 26 Answers

SOURCE: oil pressure

does the engine make any raddle noise when you start the engine. if not may just need oil presure sensor.

Posted on Jan 01, 2009

alicantecoli
  • 22095 Answers

SOURCE: Oil pressure reads high 40 to 60 psi, guage never flucuated this much before new engine

try another earth cable ?? straight to engine and chassis

Posted on May 30, 2009

youredone82
  • 426 Answers

SOURCE: need to know where heat gauge sending unit is

should be between the exhaust ports on the cylinder head, or int he intake manifold on the front of the engine near thermostat

Posted on Oct 29, 2009

moparownr
  • 667 Answers

SOURCE: oil pressure gauge shows no pressure when its cold

Jim, I think your oil pressure sender is going bad, you should replace it and see that your oil pressure is in fact good, you can also check and verify the wires to it at the same time. It is located next to the oil filter. Hope this helps, let me know

Posted on Dec 09, 2009

Testimonial: "Thank's for the info, I installed a new oil sensor and it works great. Thank's again"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

2003 ford expedition low oil pressure light. car keeps turning off. what is going on here? what is it going to cost to replace the pump ?


replace oil pressure sender switch
change oil filter
then if no better
fit a sandwich plate oil pressure reader between oil filter and block
to get the engine oil pressure when running

index-ga5va5500wygjikc4v5xzqjs-2-0_2.jpg

plate-ga5va5500wygjikc4v5xzqjs-2-1.jpg

Apr 26, 2017 | Ford Cars & Trucks

2 Answers

I have a 2003 ford ranger the oil pressure guage goes to hald way then 0 back to half way truck runs great with no problems


Check the plug first. Look at the tabs in the plugs. They should be touching from one side to the other. See a gap fix or replace the plug. If it looks good, Replace the oil sending unit.

Dec 18, 2015 | Ford Cars & Trucks

1 Answer

Power loss on Ford 302ci truck engine starts fine runs good for a short while then losses power


similar problem was caused by a blocked fuel filter. after running for a while, the dirt in the filter is drawn against the filter paper blocking the flow

Apr 25, 2014 | 2003 Ford F250

1 Answer

How does someone install manual oil pressure gauge on 2006 chevy 2500 with 6.0L Vortex


where the oil pressure sender unit is on the block install a "t" fitting . Place the electrical unit in one side and a brass fitting in the other . Run the copper line from the gauge through the firewall to the "T" piece and connect up (if you are using a plastic tube the do not waste your time as the plastic fails -cracks ,slips. or melts causing engine failure) Position the gauge and connect the copper line to the gauge . run engine and check for oil leaks.

Nov 30, 2013 | 2006 Chevrolet Silverado 2500HD 2WD

2 Answers

My 2001 Ford Ranger Edge oil pressure gauge has been jumping around all over the place. Took it in today and they said pump needs replacing... and that they had to remove the engine to do so at the tune of...


Your oil pressure gauge works with the oil pressure sensor, which is screwed into the block, to transmit a reading. A faulty oil pressure sensor can cause the reading on the gauge to be erratic. You may have a bad oil pressure sensor. You should also inspect the wires going to the sender to make sure they are not loose, corroded, or shorted. If a new sending unit doesn't work, you can check the oil pressure with a manual pressure gauge. Testing for oil pressure involves fitting the oil pressure gauge with an adapter. Then you will need to determine if you have a gauge problem or an actual oil pressure problem.

Oct 22, 2013 | Ford Cars & Trucks

3 Answers

Sludge in cooling system


Leaking head gaskets can and do cause this, the combustion gases are very corrosive and rusts the heck out of the cast iron.

Apr 20, 2017 | 1989 Ford F 150

1 Answer

No oil pressure 2000 silverado 4.8 eng


If the gauge is showing zero pressure, you would next check the pressure with a mechanical gauge to verify.
Make sure you use a tee fitting to keep the electric sensor in use while testing.
If the pressure really is zero, something has happened to the oil pump in the oil pan.

Feb 08, 2013 | Cars & Trucks

1 Answer

1998 Ford Escort 1.6 Zetec Starter motor


need to know how to fit a starter motor for a s reg escort

Jun 26, 2009 | 1998 Ford Escort

2 Answers

Oil Pressure going up and down during acceleration and decel.


Check your oil level in the engine. Oil pressure will read this way when the oil level is getting low...

May 27, 2009 | 1987 Porsche 944

1 Answer

No oil pressure


i presume you have checked the oil level... so it's likely you will have to have a new oil pump installed. how are you checking the pressure by the way. if it's by the gauge on the truck consider taking it to a shop to confirm you have no pressure

Mar 04, 2009 | 1988 Ford F 250

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5471 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...