Question about 2001 Pontiac Aztek

1 Answer

WHERE DO YOU FIND HARNESS FOR TRAILER WIRE - 2001 Pontiac Aztek

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Pontiac Master
  • 540 Answers

Their is no factory harness with trailor wires, you have to buy the pigtail, and wire it, or have it wired in, but they are available

Posted on Aug 26, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wiring diagram


Hook up the trailer to the vehicle. Under the rear bumper you will find a thick wire harness that runs from left to right or vica versa. Choose a location to strip open the harness to gain access to the different color wires. Open the trailer coupling. remove all wires and split them apart. Now start with say the right indicator light on the vehicle. Earth should be established via the grounding method of the trailer hook steel on steel of the vehicle. Connect any wire of the trailer to the now flashing right indicator light. Go through them all till the right indicator bulb flashes on the trailer. A good approach to determine which wire is active, is to make a test light from an old bulb connector some have already two wires connected ie; pos neg. neg the tester onto any part of the vehicle chassis and the pos to the now live wire. Go through them all till all wires meet up. Now go on and extend the harness by means of soldering properly and insulating that wire from the main harness to the female fitting of the trailer connector. At each connection on the fitting fit on properly the different wires and do the same to the male connector from the trailer so that all lines up inside the two connectors. Good luck

Aug 14, 2013 | 1993 Land Rover Defender

1 Answer

My o3 navigators adjustable brakes will only move about 1/2 inch either direction. It's fine if they don't work but is there any way to move them to the farthest position manually?


With both tail light lenses removed locate the black with yellow wires and the dark green with brown wires coming out of the brake/tail/turn signal sockets.

The black with yellow wire will be the running lights or tail lights and the brown wire from the trailer harness will attach to it.

The green wire on the trailer harness will be the right turn signal and will be attached to the passenger side tail light harness dark green with brown wire.

The yellow wire on the trailer harness will be the left turn signal and will be attatched to the dark green with brown wire on the drivers side tail light harness.

The white wire on the trailer harness is the ground wire and will need to be attached to a good ground. Is it pretty easy to crimp an eyelet onto the end of the wire and use a self tapping screw to attach it to the body behind one of the tail light lenses.

Here is a trailer light/wiring article I have done in the past. It has a couple of good tips you may find useful.

http://www.hotspotoutdoors.com/forum/ubbthreads.php/topics/1425999/1/Trailer_Wiring_101

Oct 27, 2010 | 2003 Lincoln Navigator

1 Answer

How to wire a 4 pin connector for a LED Tailgate bar into the brake lines on a 2000 dodge dakota without trailor plug


With both tail light lenses removed locate the black with yellow wires and the dark green with brown wires coming out of the brake/tail/turn signal sockets.

The black with yellow wire will be the running lights or tail lights and the brown wire from the trailer harness will attach to it.

The green wire on the trailer harness will be the right turn signal and will be attached to the passenger side tail light harness dark green with brown wire.

The yellow wire on the trailer harness will be the left turn signal and will be attached to the dark green with brown wire on the drivers side tail light harness.

The white wire on the trailer harness is the ground wire and will need to be attached to a good ground. Is it pretty easy to crimp an eyelet onto the end of the wire and use a self tapping screw to attach it to the body behind one of the tail light lenses.

Here is a trailer light/wiring article I have done in the past. It has a couple of good tips you may find useful.

http://www.hotspotoutdoors.com/forum/ubbthreads.php/topics/1425999/1/Trailer_Wiring_101

Oct 27, 2010 | 2001 Dodge Dakota

2 Answers

SemiTrailer Wiring when I turn on my left turn signal all lights blink.


sounds like if its a 2 filiment bulb(1156) one of the filiments is touching the other and back feeding the signal,start by removing all signal bulbs and replace each with a new one as a test,also reground all grounds,if the signal cant find reference ground it will take the next path to find it,if this doesnt work then possibly you have wires in the frame bare and touching

Mar 18, 2010 | 2004 Dodge Ram 1500

1 Answer

Were do you hook up the two wires under the hood for trailer brakes on a 2000 silverado


Sometime around 2000, GM started putting trailering pre-wire harnesses in the vehicle. Your truck may have this harness built in and would greatly simplify brake controller installation. Look under the glovebox and see if there is a wire harness tied off. There will be four wires in this harness, which should be run over to the steering column to use it. Most trailer brake controllers are compatible with this harness.
The four wires in the harness are: Red, 12vdc; black, ground; blue or purple, brake pedal; and brown or white, trailer brake wire to seven pin, four pin, or five pin connector at trailer hitch, if your truck came from the factory with a trailer hitch.
If you are adding the hitch and do not have the four wire harness, the under hood wires from your brake controller are Red, connect to one of the studs under the distribution box cover (the distribution box is on the driver's side against the firewall. Underneath the cover are two large threaded studs which are hot from the battery all the time); and the other wire from your brake controller would have to be run the length of the truck along the frame, tied off in several places, to the trailer hitch connector on the bumper. Follow the directions that came with trailer hitch wiring connector to connect this wire to the proper pin in the connector.
If this has helped you, great, and please remember to vote/comment.
Good luck!

Feb 21, 2010 | 2000 Chevrolet Silverado 1500

3 Answers

Which fuse controls trailer brake lights ,left side works right doesn't


seperate fuse box under hood some time, alldatta is in your library

Feb 17, 2010 | 2006 Dodge Ram 3500 Truck

2 Answers

Trailer hitch...no running lights (2004)


You'll have to follow the BROWN wire from the factory connector(with the running lights on of course) to the trailer connector and make sure you are getting power all the way to the two lamp fixtures. If so you've probably got two burned out 1157 bulbs or an inline fuse in the factory harness/ trailer harness.Good Luck, Dana

Aug 24, 2009 | 1991 Dodge Dakota

1 Answer

Trailer harness


Check power converter to the harness. It is possible to wire a standard 4 wire harness into the system and bypass the turn signals. If there is seperate brake and turn signal bulbs, there has to be a converter used to get the signals to work. Also... try http://www.etrailer.com/faq-wiring.aspx. This should help.

Aug 07, 2009 | 2006 GMC Savana

1 Answer

Trying to hook up trailer lights


taillights on what? Everything - needs to be grounded is the FIRST thing to remember. Try etrailers.com for parts or tech assistance or Google "Hoppy" trailer light kits.
Good luck

Jun 14, 2009 | 1992 Mazda B-Series

1 Answer

Trailer harness on a 1994 suburban gmc


sounds like you bought the male trailer side,the trailer side comes with an additional white wire for trailer ground,sounds like your already wired for trailer lights

Mar 24, 2009 | 1994 GMC Suburban

Not finding what you are looking for?
2001 Pontiac Aztek Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...