Question about 1999 Dodge Durango

2 Answers

I replace the master cyl now I don't have fluid going to the back liner just the front.

Posted by on


2 Answers

  • Level 1:

    An expert who has achieved level 1.


    An expert that has over 10 points.


    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 16 Answers

Did you bleed the master cyl. before installing

Posted on Aug 25, 2010

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 220 Answers

Air in system...........Start bleeding at the farthest wheel from Cylinder which is normally right rear then go to left rear then right front then left front. This will work all the air back out through the cylinder. Takes some time to do it like this but only other way is to take it to a shop where they can put a pressure bleed system on it to make sure all the air is removed.

Posted on Aug 25, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Replaced some brake line, rear pads and one rear wheel cylinder. Now no pressure and nothing happening when trying to bleed.

Does the car have ABS ? And does it have an equalizer block for the 4 wheels ?
It sounds like the ABS has been affected, or there is an equalizer block that is stuck on the front wheels only.
Can you open the bleeder or the rear line on the master cyl and get fluid to come out by depressing the pedal ?

Jul 07, 2013 | 1997 Mercury Tracer

1 Answer

E brake light won't turn off after I release the e

There is usually a float in the master cyl resivoire. It is poss low on fluid. You either have a leak, low fluid or pads worn out. The fluid will go in to the cylinders of the calipers when the pads are replaced the piston on the caliper gets pressed back in the caliper forcing the fluid back in to the master cil resivoire turning off the light. Please don't fool around with safety items on our car. Have them checked by a licensed technician.

Apr 02, 2012 | 1992 Ford Taurus

1 Answer

Front brakes sticking on almost every trip. New calipers new master cylinders,new hoses, new fluid new vaccum valve to servo, new vaccum unit but still happening Where's the problem !998 806 Eden...

A few items you could ckeck, adjustment of the pushrod from the pedal to the master [ if it's set to long, the pistons inside the master Cyl. wouldn't retact enough to let the fluid flow back into the master Cyl, properly causing the calipers to drag. this would become worse when the fluid and master heated up.], - The proportening valve may be faulty and blocking the fluid from returning to the master from the front brakes, - If the vehicle has Anti-lock brakes it could be in that system.
Good hunting!

Apr 08, 2011 | Peugeot Liberte Cars & Trucks

2 Answers

No Brakes, changed Booster, thought it was air in the lines. When bleeding no fluid coming out of front right and back brake bleeder valves. Checked rubber line, is ok. Clogged somewhere in the line. Have...

Is the master cylinder good? a bad master can cause this also did you bleed the master first before bleeding at the wheel and also make sure the bleeder screw is clean, if the hose is good then theres only a few things, a bad master or a master that wasnt bleed, try bleeding the master first then try rebleeding the brakes.

Mar 01, 2011 | 1983 Ford Thunderbird

1 Answer

I replaced master cylinder bleed brakes back brakes working but no brakes front . No brake fluid on bleeders in front . What next to do . Toyota cressida 1985 2.8i automatic

Bleed front more. If needed, remove line from each front caliper to ensure fluid is flowing. If no fluid movement you may have a bad master cyl.

Jan 20, 2011 | 1985 Toyota Cressida

2 Answers

95 chevy silverado, brake fluid was contaminated and master cylinder went out. Replaced master cylinder and flushed out all of the bad fluid. Now the front breaks are locking up when applying medium to...

Hello: You nare going to have to replace/rebuild front calipers, replace Both rubber hoses that go fron the frame to the calipers. You may have to replace the rubber hoses in the rear and the rear wheel cylinders. Contaminated brake fluid creates a expensive and long repair.

Jan 10, 2011 | Chevrolet 1500 Cars & Trucks

2 Answers

Bleeding brakes

always bleed front driver side first, front right,left back
right back.
make sure you always have oil in the master

Apr 08, 2009 | 1993 Dodge Dakota

1 Answer

No front brakes on 94 dodge 4x4 1/2 ton

is your abs light on. sometimes the anti lock brakes malfunction, if fkuid comes out when bleeding the front brakes then you probably have a leak the master cyl has a plastic resivior. look at the vase of the tank where it plugs into the master if you move it and see fluid you are leaking bexause of the wrong part. sen this a lot. also if no fluid comes out when bleeding front brakes you have a bad rubber line. just some thing
s to check.

Nov 29, 2008 | 2000 Dodge Ram 1500 Truck

1 Answer

Hi.what is the name of the wires going to under the master cylinder at the front end of the master cylinder ,I have a ford windstar 1998

do you mean the wires that go to the plug on bottom of master cyl or the plug on the side of master cyl ?
the wires to the plug on the side of the master cyl are to the brake fluid level sensor.
the wires to the plug on bottom of the master cyl are to either a brake pressure switch or a brake pressure transducer.

Nov 14, 2008 | 1998 Ford Windstar

1 Answer

How to remove front brake pads from a 2004 Diahatsu Charade

what i do is remove fluid from master cyl. in engne bay. jack up front, remove wheels. with decent flat blade push piston back through caliper between inner pad and rotor. remove lower caiper bolt (12mm). pivot caliper up remove old pads, fit new pads. Check inner and outter pads and dont forget the shims!!! refit lower bolt. pump brake pedel. top up fluid in master cyl. refit wheels. go for drive to bed in. accel. to 60kmh brake to 20kmh repeat 5 times.

Aug 09, 2008 | 1988 Daihatsu Charade

Not finding what you are looking for?
1999 Dodge Durango Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8499 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides