Question about 1993 Ford Econoline

1 Answer

How does the belt go back on pullys came off - 1993 Ford Econoline

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 103 Answers

There is a diagram on the core support to show you the routing of the drivebelt

Posted on Aug 25, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change serpentine belt on 2006 buick lacrosse


Start by drawing a diagram of the belt routing. Serpentine belts normaly have 1 spring loaded tensioner (1 pully will have a nut or 3/8 or 1/2 inch drive hole) That will be the tensioner. get spanner or ratchet to fit & lever the tensioner away from the belt. Remove belt. fit new belt to most pullys except the easiest to get to, lever the tenioner back & fit the belt to the last pully, Check the belt is on all pullys properly & your done

Jun 28, 2012 | Cars & Trucks

1 Answer

1993 doge caravan belt replace


If you need to replace it, the diagram for the belt position should be under the hood near the radiator cap. You need to loosen the tensoiner pully using a socket wrench and and pull and hold the pully up and take the old belt off. To install the new one route the belt back through the pullys and pull the tensioner pully to slide the last part of the belt in place and let the pully down and it will hold the belt in place.

Dec 26, 2011 | Cars & Trucks

1 Answer

Whaere is the water pump located


The water pump is on the top right hand side of the engine if you standing on the passenger side looking at the front of the engine. Keep in mind that the water pump only goes back on one way, so make sure that you have it clocked right or the bolts wont line back up. Remove the water pump pully first before you take the belt off. This makes it easier to break the pully bolts loose and then remove the water pump bolts. Then after, put the pully back on and then the belt and then tighten the pully bolts, the belt will help hod the pully for you.


360dreamworx_44.gif
360dreamworx_45.gif
360dreamworx_46.gif

Aug 08, 2011 | 2003 Buick Rendezvous

1 Answer

Diagram of pullies and belts on 86 toyota mr2


If you are talking the a/c pulley and alternator pulley, I am pretty sure the belts are different sizes (different number of ribs in the belt). So, you can just look carefully at the ribs and put the right belt on the right pully. from memory, the A/C belt goes on first and all the pullies towards the front of the car are used for that belt. The Alternator belt goes on next, and all the pullies from the crank shaft toward the back of the car (from the crank pulley) go to that. I could have those reversed, but the ribs on the belt will show you for sure. have fun!

Mar 06, 2010 | 1986 Toyota MR2

1 Answer

I have a ford galaxy and my power steering belt has snaped the new one wont fit back on witch pully is the ajuster


if you look at the engine youll see the alternator directly above the alternator you will see a pully which doesnt have grooves on the surface like the rest of the pullys. this smooth pully is the tensioner pully and you will need to use a large ratchet or spanner to to lift up the pully (its on a spring) so you can fit the belt.
shiney pullys indicate that they sit or rest on the outside of the belt.

hope this helps

Dec 19, 2009 | 1985 Ford EXP

2 Answers

How do you adjust tension for drive belt


first you need to figure out if you have an automatic tensioner or an adjustable one. so look at the pullies which ones are not accesories (ie not an alternator pully, power steering.) some pullies will just be on there own not driving anything. is this pully connected to something like this O>o <--this end is the pully.
pully mounting bolt ^ ^arm with hole for rachet
or does it look like the pully is attached to a threaded pole.

the auto adjuster need a rachet to pull back on it (because it's spring loaded) while you install the new belt.

the other need the nut on the pully loosened and the threaded pole loosened will move the pully removing tension from the belt (opposite will tension the new belt).

tighten belt until you can only twist it in half.

Jun 25, 2009 | 2003 Toyota Camry

1 Answer

Replace serpentine belt in 1996 Grand AM


One belt to replace, get the correct belt and wrap around all pullys, smooth pullys get smooth side of belt and rigid pullys get rigid side of belt, loosen altenator for removal and remounting then moove back to position and tighten.

Jun 13, 2009 | 1996 Pontiac Grand Am

1 Answer

Cant put on belt right


from front of engine looking back,belt around bottom of crank pully,water pump is just above,left side of belt comes around water pump going counter clock wise,put belt over alternator,then straight across to a/c compressor,(make sure belt goes under any idler pullies,smooth side of belt to smooth side of pully)find your belt tensioner,pry back on tensioner(be carefull)and carefully place belt under roller pully of the tensioner,release and check allignment of belt prior to starting.oh ya make sure belt is in good condition.

Mar 01, 2009 | 1991 Chevrolet C1500

2 Answers

Serpentine belt came off need to know how it goes back on


this is hard to exsplain without showing you a photo ,but i will try. first get the belt around the engine crankshaft which is the pully closest to the bottom and center of the engine. when standing in front of engine start to lead the belt to the right and connect to power steering pump then up to generator, next thare is going to be a smooth pully not groved like the others to the left,put the smooth side of the belt on bottom of this pully and continue left to the ac/compressor go around ac/compressor andstraight down to the belt tensioner , and then right over to the water pump which has a smooth pully not grooved. remember the smooth pullys will always carry the smooth side of the belt and the grooved pullys the grooved side of belt. the belt tensioner will half to be released by a serpantine belt tensioner tool sold at your local auto parts store. these instructions is for 3.8 liter engine, if you have a 4.6 liter engine it will be different, so repost stating that you have a 4.6 if this dont help

Dec 22, 2008 | 1997 Mercury Cougar XR7

Not finding what you are looking for?
1993 Ford Econoline Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...