Question about 1994 Chevrolet Silverado 2500

1 Answer

Steering Column Assembly - 1994 Chevrolet Silverado 2500

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

1990 chevy 2500 truck, how the steering colum come a part??

Posted on Sep 02, 2010

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 5 Answers

SOURCE: need to change blinker switch assembly in steering column

Special tool steering wheel lock plate tool at any parts store.

Posted on Mar 15, 2009

warlock61
  • 659 Answers

SOURCE: R&R Steering Wheel Assembly and/or Steering Column Assembly

if you disconnect the battery and let it sit awhile this will disable the airbag.

Posted on May 16, 2009

morse008
  • 1111 Answers

SOURCE: I need an exploded view diagram of the steering

check your local library for a manual or at a local parts store Perhaps even Wiki site

Posted on Nov 04, 2009

  • 228 Answers

SOURCE: 94 Ford Ranger, ignition assembly loose. Will not

Thats ok mam,i,m 62,retired with 19 yrs experience in automotive field.Ford cars and trucks.And several different importsBut i quit in 1996.
I,m thinking that the,gears may be out of timing and the actuating rod that moves the ignition switch contacts at or near the bottom of the steering colmn.
You should repair the key cylinder, and the tumbler that the key actuates.Then you may also need to adjust the switch assy contact box at the bottom.These are a high wear items over a lot of yrs, and useage,and might be best to pay one time, and fix it right.I used to repair tilt steering wheels,and found that its less costly just to buy a good used steering column with key and all,but now days i,m not so sure! ??? hope i was helpful!
Good luck on this problem,as i know costs are high every where.

Posted on Sep 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to remove the ignition lock cylinder from a 93 geo storm


is the lock assembly in the car or out?
there are 2 jobs here, removing the assembly
and after that, attacking the lock it self.???????

any lock smith can rebuild the lock, proper
it has pins that are pressed out.
it can even be rekeyed.

the remove assembly is covered in the FSM, no books?
alldata.com covers that.
it really is an Isuzu. impulse.

my guess is its job 1, assembly out.
so toss coin lands on job1
(on most cars, steering wheel must be removed)
once that is done, its obvious from there, right? that clamp there with the antitamper screws? then must be removed. and replaced new..

a rare car , and even more one that runs....

here is the online FSM answer

  1. Remove the negative battery cable.
  2. Remove the steering wheel.
  3. Remove the combination switch assembly.
  4. Turn the key to the OFFposition, depress the retaining pin and remove the ignition lock cylinder from the switch.
  5. Disconnect the electrical connector from the ignition switch.
  6. Remove the snapring and spacer collar from the steering shaft.
  7. Disconnect the back drive cable from the ignition switch.
  8. Remove the ignition switch bolts and the ignition switch from the steering column.


now back in?
  1. Install the ignition switch to the steering column and tighten the bolts.
  2. Connect the back drive cable to the ignition switch.
  3. Install the spacer collar and the snapring to the steering shaft.
  4. Connect the electrical connector to the ignition switch.
  5. Install the lock cylinder into the switch.
  6. Install the turn signal switch screws and the turn signal switch.
  7. Install the four screws and the coil assembly to the turn signal switch.
  8. Connect the coil assembly wiring harness to the turn signal switch.
  9. Install the two piece steering column cover and the two piece steering column cover screws.
  10. Raise the steering column and install the upper steering column mounting bolts. Tighten the bolts to 18 ft. lbs. (24 Nm).
  11. Install the left lower dash trim panel and tighten the lower dash trim panel screws.
  12. Install the lap air deflector and tighten the lap air deflector screws.
  13. Install the knee pad assembly and tighten the five screws, the bolt and the nut attaching the assembly.
  14. Install the engine hood opener cable.
  15. Install the engine hood opener and tighten the two screws.
  16. Connect the electrical connector to the cigar lighter bezel and install the bezel.
  17. Connect the electrical connector to the left switch bezel and install the bezel.
  18. Install the steering wheel.
  19. Connect the negative battery terminal to the battery.

that?

Oct 08, 2014 | 1993 Geo Storm

1 Answer

On my altima 96 when I'm parking or turning extremely slow the steering wheel somewhat locks


Hi, can you tell if it's the lock in the steering column or something with the power steering instead? If it feels like the power steering, check the belt for looseness and tighten as needed. If it feels like it's in the column, your locking assembly may be coming loose inside. Below is a procedure for removing the steering wheel lock for inspection. Please let me know if you have questions, and thanks for using FixYa.


REMOVAL & INSTALLATION The steering lock/ignition switch/warning buzzer switch assembly is attached to the steering column by special bolts whose heads shear off upon installation. The bolts must be drilled out to remove the assembly or be removed with an appropriate tool. The bolts may also be removed with a hammer and chisel by notching the bolts and tapping them counterclockwise with the hammer and chisel.
The ignition switch or warning switch can be replaced without removing the steering lock assembly. The ignition switch is on the back of the assembly and the warning switch is on the side.


CAUTION The models covered by this guide may be equipped with a Supplemental Restraint System (SRS), which uses an air bag. Whenever working near any of the SRS components, such as the impact sensors, the air bag module, steering column and instrument panel, disable the SRS, as described in Chassis Electrical .

  1. Disable the air bag system by disconnecting the negative battery cable and waiting at least 10 minutes, prior to starting this procedure.
  2. Remove the steering column covers.
  3. Remove the steering wheel.
  4. Remove the spiral cable assembly.
  5. Remove the combination switch from the steering column.
  6. Remove the steering column support nuts and lower the steering column.
  7. Disconnect the ignition switch wiring.
  8. Remove the bolts that secure the steering lock and remove the steering lock assembly.

To install:
  1. Install the steering lock assembly and secure with new shear type bolts.
  2. Connect the ignition switch wiring harness.
  3. Raise the steering column and secure with mounting nuts. Tighten the mounting nuts to 11-14 ft. lbs. (15-19 Nm).
  4. Install the spiral cable assembly.
  5. Install the combination switch.
  6. Install the steering column covers.
  7. Install the steering wheel.
  8. Connect the negative battery cable.

Apr 04, 2011 | 1996 Nissan Altima

1 Answer

How to remove a heator core from a 2001 dodge caravan? do you have to take the dash out? or just the bottom pannel.


The 2001 Dodge caravan has 2 heater cores - front (the main one), and the rear. Removal of the
rear heater core is a whole different procedure than the front.

Front Heater Core - Removal and Installation
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Align the wheels in the straight-ahead position.
  3. Disconnect the negative battery cable.
    CAUTION Before working around the steering wheel or the instrument panel all 2 minutes to pass to allow the air bag module to discharge.
  4. Drain the cooling system into a clean container for reuse.
  5. Remove the steering column, by removing or disconnect the following:

    Lower left side steering column cover Parking brake release cable from the parking brake lever 10 steering column cover liner-to-instrument panel bolts and the cover liner
  6. Rotate the key to the LOCK position; then, rotate the steering wheel to the LOCKED position.

    Gear selector cable and its mounting bracket as an assembly from the upper steering column mounting bracket 2 instrument cluster trim bezel-to-instrument panel screws, retaining clips and bezel 2 steering column shroud-to-steering column screws and the shroud Steering column-to-intermediate steering shaft coupler
  7. Loosen but do not remove the 2 lower steering column mounting bracket nuts/washers.

    2 upper steering column mounting bracket nuts/washers Steering column assembly from the vehicle
  8. Remove or disconnect the following:

    Instrument panel-to-chassis harness interconnect and bracket Lower silencer boot, at the base of the steering shaft
  9. Working in the engine compartment, pinch off the heater hoses.

    Heater core cover. Position some towels under the heater core hoses. Heater core plate and the hoses
  10. Depress the heater core retaining clips.
  11. Lift the accelerator pedal and slide the heater core past it.
  12. Depress the brake pedal and remove the heater core from the heater/air conditioning housing assembly.

    0996b43f8022fa83.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. View of the steering column assembly


    0996b43f8022fa84.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. View of the interconnect and bracket


    0996b43f8022fa85.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. View of the front heater core assembly


To install:
  1. Depress the brake pedal and install the heater core into the heater/air conditioning housing assembly.
  2. Lift the accelerator pedal and slide the heater core past it.
  3. Install or connect the following:

    Heater hoses (using new O-rings) and the heater core plate Heater core cover Heater hoses clamps, working in the engine compartment Lower silencer boot at the base of the steering shaft Instrument panel-to-chassis harness interconnect and bracket
  4. Install the steering column assembly by installing or connect the following:

    Steering column assembly, carefully into the vehicle. 2 upper and 2 lower steering column mounting bracket nuts/washers. Torque the nuts to 105 inch lbs. (12 Nm). Steering column-to-intermediate steering shaft coupler and tighten the pinch bolt to 21 ft. lbs. (28 Nm) 2 steering column shroud and the shroud-to-steering column screws Bezel, the retaining clips and the 2 instrument cluster trim bezel-to-instrument panel screws Gear selector cable and its mounting bracket as an assembly to the upper steering column mounting bracket 10 steering column cover liner and the cover liner-to-instrument panel bolts Parking brake release cable to the parking brake lever Lower left side steering column cover. Lower left side steering column cover
  5. Refill the cooling system.
  6. Connect the negative battery cable.
  7. Run the engine to normal operating temperatures; then, check the climate control operation and check for leaks.

Jan 02, 2011 | 2001 Dodge Caravan

1 Answer

Now to install igintion switch


Removal & Installation The ignition switch or warning switch can be replaced without removing the steering lock assembly. The ignition switch is on the back of the assembly and the warning switch on the side.
  1. Disconnect the negative battery cable and insulate the terminal end.

CAUTION The air bag system must be disarmed before removing the steering wheel. Failure to do so may cause accidental deployment, property damage or personal injury.

  1. Remove the steering wheel and the steering column upper and lower covers.
  2. Remove the spiral cable assembly.


23482ab.gif
View of the steering lock and ignition switch assembly

  1. Remove the combination switch from the steering column.
  2. Remove steering column support nuts and lower the steering column.
  3. Disconnect the ignition switch wiring and interlock cable (if equipped).
  4. Remove the bolts that secure the steering lock and remove steering lock assembly.
To install:
  1. Install the steering lock assembly and secure with new shear type bolts.
  2. Connect the ignition switch wiring harness and the interlock cable.
  3. Raise the steering column and secure with mounting nuts.
  4. Install the spiral cable assembly.
  5. Install the combination switch, steering column covers, and the steering wheel.
  6. Connect the negative battery cable and enable the air bag system.

May 23, 2010 | 1997 Nissan Maxima

1 Answer

2006 hhr to take out ignition switch out


Removal & Installation

1. Disable the SIR system.


28d6a49.gif
Remove the Instrument Panel (I/P) center trim panel by releasing the retaining fasteners

  1. Remove the Instrument Panel (I/P) center trim panel (1) by pulling out on the trim panel in order to release the retaining fasteners (2).
  2. Disconnect the electrical connectors on the Instrument Panel (I/P) center trim panel (1).

dc7f057.gif
Remove the steering column opening filler assembly, with clip, & bumper

3. Remove the steering column opening filler assembly (1) by pulling away the clips (2).
4. Disconnect the electrical connector for the trunk release.


77e0f1d.gif

Remove the Instrument Panel (I/P) left side trim panel

  1. Remove the Instrument Panel (I/P) left side trim panel (1).
  2. Tilt the steering wheel up.
  3. Disconnect the I/P dimmer switch and, if equipped, the fog lamp switch.

88e8dec.gif

Remove the 4 bezel screws (2) & the Instrument Panel (I/P) cluster bezel assembly (1)

  1. Tilt the steering wheel down.
  2. Remove the 4 instrument panel cluster bezel screws.
  3. Remove the instrument panel cluster bezel.

810fe4a.gif

Remove the steering column trim covers: steering column upper cover assembly, steering column left cover assembly, & steering column right cover assembly

Remove the steering column trim covers:
  • Remove the 3 cover screws (4).
  • Remove the steering column upper cover assembly (1).
  • Remove the steering column left cover assembly (2).
  • Remove the steering column right cover assembly (3).


bd6042a.gif
Removal of the ignition switch

    1. Disconnect the ignition switch harness connector.
    1. WARNING
    The ignition switch must be in the run position during removal in order to avoid damage to the ignition switch.

    1. Turn the ignition switch to the run position.
    2. Remove the ignition switch screws.
    3. Remove the ignition switch from the steering column.
    To install:
    1. Install the ignition switch and screws on to the steering column. Tighten the screws to 17 inch lbs. (2 Nm).
    2. Connect the ignition switch harness connector.
    3. Installation is the reverse of removal procedure.
    4. Tighten the trim cover screws to 17 inch lbs. (2 Nm)
    5. Tighten the 4 instrument panel cluster bezel screws to 19 inch lbs. (2 Nm)
    6. Enable the SIR system. Refer to Air Bag (Supplemental Restraint System), arming the system.
      NOTE If the ignition switch is replaced and a learn procedure is not performed, the engine will crank but not start or will start and stall immediately.

    7. Perform the vehicle theft deterrent system learn procedure.

    Mar 12, 2010 | 2006 Chevrolet HHR

    1 Answer

    Steering wheel covers


    I hope this helps....these are the steps to removing and replacing the cylinder:

    1. Remove the knee bolster.
    2. Remove the steering column trim covers from the steering column.
    3. Disconnect the steering column electrical connectors.
    4. Remove the wire harness assembly from the steering column and the wire harness strap.
    5. Slide the 2 connectors of the turn signal and multifunction switch assembly out of the bulkhead connector.
    6. Remove the key alarm connector from the lock module assembly in the following way:
    7. Rotate the key alarm connector 90 degrees.
    8. Pull the key alarm connector out of the lock module assembly.
    9. Remove the passkey connector from the lock module assembly.
    10. Remove the connector from the electric park lock, for vehicles equipped with floor shifters.
    11. Remove the ignition switch from the lock module using tool J42759 or equivalent.
    To install:
    1. Install the ignition switch to the lock module
    2. Install the key alarm connector into the lock module assembly.
    3. Push the key alarm connector into the lock module assembly.
    4. Rotate the key alarm connector 90 degrees so that the key alarm connector locks into place.
    5. Install the passkey connector into the lock module assembly.
    6. Install the connector to the electric park lock, for vehicles equipped with floor shifters.
    7. Slide the 2 connectors of the turn signal and multifunction switch into the bulkhead connector.
    8. Attach the wire harness assembly to the steering column wire harness strap.
    9. Connect the steering column electrical connectors to the vehicle.
    10. Install the trim covers to the column.
    11. Install the knee bolster.
    12. Enable the SIR system.
    13. It may be necessary to reprogram the theft deterrent system if the module was replaced.

    Mar 06, 2010 | 2001 Chevrolet Suburban

    1 Answer

    Install a Ignition lock cylinder 1997 Pontiac Grand Am


    • Ignition Removal Instructions
    • Disconnect the negative battery cable from the battery. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
    v\:* {behavior:url(#default#VML);} o\:* {behavior:url(#default#VML);} w\:* {behavior:url(#default#VML);} .shape {behavior:url(#default#VML);} Normal 0 MicrosoftInternetExplorer4 st1\:*{behavior:url(#ieooui) } /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman";}
    • Remove the upper and lower shrouds. Refer to Steering Column Trim Covers - Disassemble - Off Vehicle or Steering Column Trim Covers - Disassemble - Off Vehicle .
    • Put the key in the steering column lock cylinder set (1).

    • Turn the key to the "START" position.
    • Install a 1/16 allen wrench (2) into the hole on top of the lock module assembly in order to release the steering column lock cylinderset retaining pin.
    • Turn the steering column lock cylinder set (1) into the "RUN" position.
    • Pull the steering column lock cylinder set (1) out from the lock module assembly.
    • Remove the key from the steering column lock cylinder set (1).

    19eb1ff.png


    • Installation Instructions
    Normal 0 MicrosoftInternetExplorer4 st1\:*{behavior:url(#ieooui) } /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman";}
    • Insert the key into the steering column lock cylinder set (1).
    • LIne up the locking tab (2) and the positioning tab (3) of the steering column lock cylinder set with the locking tab slot (5) and the positioning tab slot (4) in the lock module assembly (6).
    • Push the steering column lock cylinder set (1) into the lock module assembly (6).
    • Rotate the steering column lock cylinder set (1) in the lock module assembly (6) into all positions.
    • Install the upper and lower shrouds. Refer to Steering Column Trim Covers - Assemble - Off Vehicle or Steering Column Trim Covers - Assemble - Off Vehicle
    • Remove the ignition key from the lock cylinder set (1).
    • Connect the negative battery cable to the battery. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical

    d612a25.png

    I hope this helps and good luck.
    Please remember to vote 962e1fb.jpg and leave a testimonial. Thanks.

    Nov 02, 2009 | 1997 Pontiac Grand Am

    1 Answer

    R&R Steering Wheel Assembly and/or Steering Column Assembly


    if you disconnect the battery and let it sit awhile this will disable the airbag.

    May 15, 2009 | 1998 Ford Explorer

    3 Answers

    Heater core


    18901fc.gifHere is an exploded view of the heating/air conditioning blower box. This contraption is located on the passengerside under the dash. I've changed heater cores on other cars but never worked on a caravan so not sure how difficult it'll be. You may need to remove a few cover panels to access this and the heater core #22 is located behind the distribution box #6 containing parts 7-18 and hopefully comes off as a unit. I wouldn't want to put it back together just looking at the pic. You may just need to remove the heater tube cover #4 to access the connections and slide out the core.....NAH couldn't be that simple!!! Hope this was of some help. Good luck.













    Oct 18, 2008 | 2000 Dodge Caravan

    Not finding what you are looking for?
    Cars & Trucks Logo

    157 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    yadayada
    yadayada

    Level 3 Expert

    75822 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8215 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...