Question about 1999 Plymouth Voyager

1 Answer

How do you take out the back seat - 1999 Plymouth Voyager

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Plymouth Master
  • 6,674 Answers

2 handles inside of mounts at rear near floor. Push in on buttons at top of handles and pull handles toward you (toward back door) all the way down until they snap in, and roll seat back and lift it out.

Posted on Aug 26, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the back seat to install seat covers on my 2014 chevy cruz?


Try this for the back seat: Pull the back seat down. Unscrew all the bolts behind the back seats to release it from the brace. Pull the seat back off the rear deck and out of the car. Feel under the seat cushions for release tabs on both sides. Pull the release tabs to loosen the seat cushion. Push the seat belt buckles into the holes to prevent the seat from getting caught up in the seat cushion

Jun 08, 2016 | Chevrolet Cruze Cars & Trucks

1 Answer

On my extended cab, the front passenger seat will not slide all the way back to the lock position


There's probably something in the way. Get under and behind the seat with a flashlight and check the back end of the rails to see if something is there.

Jul 09, 2017 | 1993 GMC Sierra

3 Answers

How to remove back seat in 1972 buick skylark


Remove the seat cushion retaining bolts, detach the seat cushion and remove it up and out from the vehicle.

Remove the rear seat back retaining bolts at the bottom of the seat back. Pull up then out to disengage the upper frame from the hangers and remove seat back from the vehicle.

Installation is the reverse of removal.

Courtesy: Haynes GM repair Manual #38025. You can probably find a copy of it on Amazon or eBay cheap

Jun 20, 2011 | Buick Skylark Cars & Trucks

1 Answer

Ait bag warning light on, plus passenger seat doesnt fold forward correctly and difficult to get back in the correct position after letting passengers into the rear. 2002 cooper. thanks


Regarding the passenger seat, to allow someone into the back seat, push the seat back lever DOWN. This will flip the back of the seat forward and allow the seat to slide forward. Simply push firmly on the seat back (no need to touch the lever) and it will return to its original position.

If you pull the seat back lever UP, you can adjust the recline angle of the seat back. Pulling the lever UP will also let you fold the seat and slide it forward, however, it will not return to its original position.

Sorry, cannot solve your airbag question.

Mar 11, 2011 | 2002 Mini Cooper

1 Answer

How do you fold down back seats


Look at the seats where the back meets the seat itself. Between the seal belt belts, you should see two nylon loops. Just pull those loops and the seat bottoms will fold up against the back of the front seats. Then the seat backs just fold down. Remember to take the headrests out of the seat backs - you'll find storage for them on the up side on the seat bottoms.

Feb 18, 2011 | 1997 GMC Yukon

1 Answer

We need to remove the drives side head rest to install a seat cover, but we cannot figure out how to remove the head rest. How do you remove the driver's side head rest?


Head Restraints Removal
  1. Unscrew front seat head rest guide rod retainers (610A18) .
  1. Pull up on front seat back head restraint (611A08) . Compress foam in area of front seat head rest guide rod sleeves (610A16) .
  1. Remove front seat back head restraint positioning springs. Pull front seat back head restraint up and out.
Installation
  1. Slide front seat head rest guide rod retainers onto front seat back head restraint posts.
  1. Compress foam in front seat head rest guide rod sleeve area. Install positioning springs on front seat head rest guide rod sleeves .
  1. Insert front seat back head restraint posts (notches on posts facing rearward) into front seat head rest guide rod sleeves and push down to engage positioning spring.
  1. NOTE: Front seat back head restraint must operate smoothly throughout its range of travel, must remain in any fixed position, and must not be freely removable from the seat back. If any of these conditions are not met, check for proper installation of positioning spring onto front seat head rest guide rod sleeve .

    Tighten front seat head rest guide rod retainers onto front seat head rest guide rod sleeves .
  1. Adjust front seat back head restraint by applying hand pressure, either up or down, to center area of front seat back head restraint .

9a4d433.gif

Aug 21, 2010 | 1998 Ford Taurus

1 Answer

How do i remove the front seats of a 1998 Pontiac Grand Prix?


On W-Body vehicles, the front seats are secured to the floorpan by two front hook attachments and two rear bolts installed to nuts welded to the floorpan.
The manually operated two-way front adjusters provides only fore and aft movement of the seat. When the seat adjuster handle located on the front seat is pulled up, the seat adjusters unlock, permitting travel of the seat. When the seat is in the desired position and the seat adjuster handle is released, the seat locks in place.
A power operated six-way seat adjuster is available. The adjusters are activated by three 12 volt, reversible, permanent magnet motors with a built-in circuit breaker. The motors are energized by a switch bolted on the seat side panel.
The three motors drive the front seat and rear vertical actuators and a horizontal actuator. When the adjusters reach the limit of travel, torque is absorbed through the rubber mounted grommets located between the motor and the support. An overload relay is provided in the circuit and will open should excessive stall be applied.
The optional 60/40 split bench front seats have seat back head restraints on the driver's and passenger's seat back. The head restraints are designed so they cannot be removed from the seat back without first inserting a small rounded tool inside the head restraint support tube to release the locking tab. The 60/40 split bench seat is equipped with a reclining mechanism on both the driver's and passenger's side. The recliner lever is located on the outboard side of the spring cushion. When the lever is pulled upward, the spring loaded dual linear reclining unit located in the cushion frame is released, allowing the seat back to be pushed rearward or allowing the spring loaded reclining unit to bring the seat back forward.
Bucket seats are equipped with manual reclining mechanisms. An optional six-way power seat adjuster is available. Some bucket seats are equipped with inertia seat back locks. This system allows the seat back to fold forward without requiring the occupant to release a locking lever or access to the rear seat area. During a sudden stop or deceleration, or if the front of the vehicle is nose down, the inertia system of the seat back lock will engage, holding the seat back in its rest position. A release lever is provided to allow manual release of the seat back lock when the vehicle is in the nose down position. The release lever is located at the lower rear outboard corner of the seat back.
Some W-Body vehicles (notably Pontiac coupes) have passenger front seats equipped with an E-Z Entry device. This is actuated, in an unoccupied seat, by completely folding the seat back forward disengaging the adjuster, and sliding the front seat forward to gain access to the rear seat area. To return the seat to its normal position, return the seat back to its rest position, and slide the entire seat rearward, engaging the adjuster.
W-Body rear seats are available in several styles including a rear seat with an integral child restraint device.

Sep 01, 2009 | 1998 Pontiac Grand Prix

1 Answer

How do you remove the headrest on a 1996 ford crown victoria?


Head Restraints Each front seat is equipped with dual-post design front seat back head restraint (611A08). The front seat back head restraint is installed as follows:
  • It travels on dual posts which have notches to engage a spring-loaded catch in the guide.
  • The front seat back spring assembly retains the front seat head rest guide rod sleeve (610A16).
  • The front seat back head restraint is adjustable from its normal position to a raised position of approximately 25 mm (1 inch).
  • Pull up on the front seat back head restraint to raise it. Pushing down will return it to its normal position.
----------------------------------------------------------------------------------------------

Removal
  1. Unscrew front seat head rest guide rod retainers (610A18).
  1. Pull up on front seat back head restraint (611A08). Compress foam in area of front seat head rest guide rod sleeves (610A16).
  1. Remove front seat back head restraint positioning springs. Pull front seat back head restraint up and out.
Installation
  1. Slide front seat head rest guide rod retainers onto front seat back head restraint posts.
  1. Compress foam in front seat head rest guide rod sleeve area. Install positioning springs on front seat head rest guide rod sleeves.
  1. Insert front seat back head restraint posts (notches on posts facing rearward) into front seat head rest guide rod sleeves and push down to engage positioning spring.
  1. Tighten front seat head rest guide rod retainers onto front seat head rest guide rod sleeves.
  1. NOTE: Front seat back head restraint must operate smoothly throughout its range of travel, must remain in any fixed position, and must not be freely removable from the seat back. If any of these conditions are not met, check for proper installation of positioning spring onto front seat head rest guide rod sleeve.

    Adjust front seat back head restraint by applying hand pressure, either up or down, to center area of front seat back head restraint.

Mar 01, 2009 | 1996 Ford Crown Victoria

Not finding what you are looking for?
1999 Plymouth Voyager Logo

Related Topics:

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...