Question about 2000 Chevrolet Malibu

1 Answer

Want instructions to remove a engine motor and install a new engine motor in a 2000 chevey malibu 3.1L V6 engine NF4

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 2,309 Answers

That is major surgery, buy a good manual or go to autozone, chilton or mitchell on line to download info

Posted on Aug 25, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

07 chevy malibu engine wiring


May 06, 2014 | 2007 Chevrolet Malibu

1 Answer

Remove golve compartment on 1999 chevy malibu

There's only so many screws that hold the glove box in. Some are inside the glove box and some are underneath. You may need a torx wrench depending on the type of screws holding the glove box in.

Feb 18, 2013 | 2000 Chevrolet Malibu

3 Answers

How to replace starter for 2000 Isuzu Redo V6

Below are some instructions for you. Yes the pipe has to be removed in order to get the strarter out once it has been unbolted from the engine/transmission. Looks like it's possible to do it without removing the pipe but believe me I have tries and it just wont come out unless you do remove the pipe. Hope this helps and don't forget to disconnect the ground wire on the battery before you start the job. Installation is in reverse order as taking it off.


Dec 25, 2012 | 2000 Isuzu Rodeo

1 Answer

Blower motor runs for a few minutes then slows down then stops I have already changed out the resistor

change out the blower motor instructions below!
  • Disconnect the negative battery cable.
  • Disconnect the blower motor lead connector from the wiring harness connector.
  • Remove the blower motor cooling tube from the blower motor.
  • Remove the four retaining screws.
  • Turn the motor and the wheel assembly slightly to the right so that the bottom edge of the mounting plate follows the contour of the wheel well splash panel.
  • Lift up on the blower and remove it from the blower housing.
  • Installation the new blower motor by reversing the removal steps.
  • Connect the negative battery cable.
  • Dec 22, 2010 | 2000 Chevrolet Malibu

    1 Answer

    How do you replace the thermostat on a 2002 chevey malibu

    Where the top radiator hose clamps to the engine is the thermostat housing. Take hose off. Take two bolts off. See how old thermostat comes out so you can put new one in the same. Use blade or scraper to clean both surfaces well. Put gasket and new thermostat in and bolt it down. Re clamp hose and refill coolant. Check for leaks

    Oct 02, 2010 | 2002 Chevrolet Malibu

    1 Answer

    I cant use the button or key to unlock my trunk

    lift seat bottom up at the 2 corners very sharply. for back of seat there are 2 nuts to take off, on each bottom side. then pull back up and off of clips.

    Nov 10, 2009 | 2000 Chevrolet Malibu

    1 Answer

    Instructions for installing a radiator on a 1998 Chevy Malibu V6 engine

    If you can't look at it and see what needs to be removed and replaced then you should hire it done. Remove the covers the fans and unhooking the fans wireing the upper raditor suport the trans cooling lines pluggin them with hose with bolt in it til the new ones in and watch for the rubber peices on the bottom and make sure they line up and don't force anything as it'll go together like butter if your right. force needed back up and try again it's easy just remenber that and when your done, you;ll say I'm right if you did'nrt try to do it wrong

    Oct 19, 2009 | 1998 Chevrolet Malibu

    2 Answers

    1998 chevey malibu

    on 2000 malibu there is 1 on each side of dash, and 1 under the hood on drivers side.

    Jan 17, 2009 | 1998 Chevrolet Malibu

    1 Answer

    97 chev malibu serpin belt dig

    go to ask .com and put in the search belt routing for a 97 chevey malibu 3.1 or 3.8 engine what ever u have in your car

    Dec 20, 2008 | Chevrolet Caprice Cars & Trucks

    2 Answers

    Serpentine belt 2000 chevy malibu putting one on

    first of all,put a jack under engine, put wood on top to prevent from hurting engine,jack up till a little tension is on jack to support engine.release tensioner, a 3/8 breaker bar will work in the square part of remove cruise control from braket and set aside.remove motor mount.if need be, jack engine up to remove belt. 3.1 v6

    Oct 31, 2008 | 1998 BMW M3

    Not finding what you are looking for?
    2000 Chevrolet Malibu Logo

    Related Topics:

    50 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts


    Level 3 Expert

    76630 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22219 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8514 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides