Question about 1996 Nissan Altima

Open Question

How to replace a speed sensor in 1996 nissan altima gxe, with automatic transmission.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: 2003 nissan altima 2.5s transmission rough shift

Probably sensors! I have already replaced the crankshaft positioning sensor once, nissan replaced it once under recall and now it is bad again! Plus my speed sensor is bad too! Go to any part store and get diagnostic test ran, it will tell what sensors are bad.

Posted on Oct 02, 2008

Ad

SOURCE: 2003 Nissan Altima?

Where is the sensor placed on the car?

Posted on Oct 07, 2008

cris_p
  • 62 Answers

SOURCE: how to replace knock sensor in 1995 nissan altima

remove the intake manifold ,remove radiator ,remove radiator intake and outake housing, remove fan ,remove all belts: power steering, alternator and if you have a/c, remove harmonic balancer ,remove timing belt covers, remove timing belt remove intake housinng once you have remove all the above, your freaken engine will look naked, you can see the location of the knock sensor is locate in the engine valley

Posted on Feb 19, 2010

  • 1 Answer

SOURCE: how to change motor mounts on a 1996 nissan altima gxe

install motor mount

Posted on Mar 13, 2010

ZJLimited
  • 17970 Answers

SOURCE: How do you remove a 1999 Nissan Altima starter?

Nissan Car Altima & Sentra 1999-06 StarterRemoval & Installation

  1. Remove or disconnect the following:
    Negative battery cable Air duct Harness protector from the harness Starter wiring at the starter Starter-to-engine bolts Starter from the vehicle


  2. b53bb6c.jpg
    Fig. Starter location and mounting detail-3.0L Maxima with a manual transaxle


    b2eb267.jpg
    Fig. Starter location and mounting detail-3.5L Maxima

To install:
  1. Install or connect the following:
    Starter and torque the long bolt to 57-72 ft. lbs. (77-98 Nm) on Altima and Maxima and 41 ft. lbs. (55 Nm) on 350 Z. torque the short bolt to 22-30 ft. lbs. (30-41 Nm) Starter wiring Harness protector Air duct Negative battery cable
  1. Remove or disconnect the following:
    Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter

To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

1.6L & 2.0L Engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negaative battery cable

1.6L, 1.8L & 2.0L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negative battery cable

1.8L & 2.0L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negative battery cable

2.4L & 2.5L Engines
  1. Remove or disconnect the following:
    Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

2.4L Engine
  1. Remove or disconnect the following:
    Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

2.5L Engine
  1. Remove or disconnect the following:
    Negative battery cable Air cleaner cover and duct Harness bracket Wiring at the starter Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

3.5L Engines
  1. Remove or disconnect the following:
    Negative battery cable Air cleaner case (upper) and air cleaner to electric throttle control actuator tube. Harness protector from the harness Starter wiring at the starter Starter-to-engine bolts Starter from the vehicle

    42c548c.jpg
    Fig. Starter location and mounting detail-3.5L engine

continue...

Posted on Apr 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to add automatic transmission fluid to my 2001 nissan altima gxe. But so far I could not locate the reservoir. Some one please help. Thanks


No reservoir,it goes in where the dip stick is,remove and put a funnel in hole and add,always check when engine is running and in park.

Feb 03, 2014 | 2001 Nissan Altima

1 Answer

2000 nissan sentra gxe code output speed sensor


It sounds like the transmission is slipping and the sensor is just reporting this info and setting a code, you have made a common mistake. You likely need a transmission overhaul

Oct 05, 2012 | 2000 Nissan Sentra

2 Answers

Location of knock sensor on a 1996 Nissan Altima GXE engine?


The knock sensor is underneath the intake manifold on the rear of the engine.
If you got an engine check code from Autozone or some other goof ball company like that go and get a full tank of the highest quality gas and see if that fixes the problem.

Aug 04, 2010 | 1996 Nissan Altima

2 Answers

NEED T LOCATE SPEED SENSOR ON A 2003 NISSAN ALTIMA


Hello irmagrita
The speed sensor is located on the right front front of the transaxle near
the right axle flange. With automatic transmission.

On the manual trans. it's located on the transaxle.
I hope this helps.

Jul 10, 2010 | 2003 Nissan Altima

3 Answers

Speed sensor location on a Nissan Maxima 2000 gxe


There are two speed sensors one is called a revolution sensor that is located on the case of the transmission. You can take the driver side wheel off and see the sensor on the top of the case of the transmission. A 10mm bolt is holding it in. Easy fix

May 20, 2010 | 2000 Nissan Maxima

1 Answer

I have a 96 Nissan Altima GXE with the 2.4 liter motor that has a problem code coming up P1401 do u know what it is


this code is telling you something is wrong with your EGR temp sensor circuit, this is due to an extreme low or high voltage detection from the sensor by your cars ECM computer. check the harness connections or check/ place your EGR temperature sensor, this should solve your issue, thanks

Oct 02, 2009 | 1996 Nissan Altima

1 Answer

1996 Crysler Conv automatic Transmission


try changeing both your input and ouput speed sensors on your transmission located on the side should be 1" plastic plug with a two wire connector

Sep 19, 2009 | 1993 Nissan Altima

1 Answer

Where is the crankshaft position sensor on a 1993 nissan altima gxe?


if I may remember, I believe its on the transmission's bell housing up front below the radiator outlet hose. Its a black sensor mounted to the transmission. Hopefully this helps!!

Aug 07, 2009 | 1993 Nissan Altima

1 Answer

Car keeps cutting off


get an odb2 make sure their is no other faults.
they are cheep

Sep 15, 2017 | 1996 Nissan Altima

1 Answer

2003 nissan altima 2.5s transmission rough shift


Probably sensors! I have already replaced the crankshaft positioning sensor once, nissan replaced it once under recall and now it is bad again! Plus my speed sensor is bad too! Go to any part store and get diagnostic test ran, it will tell what sensors are bad.

Sep 25, 2008 | 2003 Nissan Altima

Not finding what you are looking for?
1996 Nissan Altima Logo

Related Topics:

431 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

78257 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...