Question about 2002 Chrysler Town & Country

1 Answer

The wiper fluid does not come out of the back window. What causes this?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,102 Answers

Hi their could be a couple of reasons, one being the nozzle at the back blocked you can get a small pin and give it a good poke to get any grit or grime out that could be blocking it.

if it dont work after doing that then the problem is usually gel build up, this happens when you put washer fluid in the bottle then over time it turns to gel in the bottom of the washer bottle and this then sometimes gets sucked into the pump causing it to get blocked, now one thing you can do is empty the washer bottle and fill it up with hot water doing this will sometimes break the gel up and get it working again.

if it still dont work then all their is left to do is replace the pump, this is located in the bottom of the washer bottle and has wires going to it that are just a push fit then the pump itself is just pushed into a rubber bung in the bottom of the washer bottle.

let me know if you need further assistance ok

plz could you rate this solution as i have pages of unrated posts, thanks

Posted on Aug 25, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When starting wipers came on and stay on no matter of position of control, washer fluid over head dome light won't turn on, rear washer and whiper won't work.


Wipers won't turn off......sometimes! - Ford Truck Enthusiasts Forums

www.ford-trucks.com > ... > Diesel > 6.7L Power Stroke Diesel
Feb 3, 2014 - Starting around 25,000 miles my wipers stayed on the slowest intermittent setting even when ... They only two that come to mind is the switch inside the cab or the wiper motor control board. ... The wipers do not park at the correctposition ... It doesn't really matter what steps need to be taken to fix the issue.

Window washer fluid put in window washer won't work now.

www.cargurus.com > Questions > Kia > Sorento

CarGurusAug 31, 2015 - Window washer fluid put in window washer won't work now. ... 4 answers. wipers working, not the washer though, pulled pump, intake screen clean. 2011 Kia Sorento Base ... Interior lights do not work when door is opened 7 answers. At first the back seat overhead light stopped working. Kia said it would ...

Nov 26, 2015 | 2011 Dodge Durango RT

2 Answers

Jeep wrangler wiper fluid will not dispense on front windsheld but will on the rear


Switch is faulty is the first thing comes to my mind. Your spot on tho in your diagnosis, although you may have two pumps and tanks, one for front, one for rear. I would check all my fuses just to be sure, and I would look at all my waster tubes and make sure they are not clogged, check your nozzles too, as sometimes wax can clog them up.

Dec 16, 2013 | 2008 Jeep Wrangler Rubicon

1 Answer

My window wipers work but my window washer fluid doesn't work is there a fuse for it and if so were is it cause I can't find. Also under the hood fuse box has CMH on it but when I opened it up there was...


It sounds like the seal in the washer pump has worn and let washer fluid into the little motor, causing it to corrode and seize. Pump is usually located on bottom of washer fluid bottle.

Aug 20, 2010 | 1990 Toyota Pickup

2 Answers

Rear window washer does not spray fluid. When I push the rear window washer button, the front washer/wipers turn on. The rear wipers work normally.


I have the same problem with my 2000 chevy blazer as skornec had posted. I kinda already figured the hose or spray nozzle was plugged. But the problem with checking those items is that I don't know where the hose is located to the back wiper. And the only thing that could be I see that could be the spray nozzle doesn't even have holes that washer fluid could spray from. So basically I just would LOVE if someone could please inform this lame brain of where to find the spray nozzle on the rear window and where in the interior of my blazer does the washer hose run.

Apr 02, 2010 | 2000 Hyundai Accent

2 Answers

2004 4runner rear wipe blade and fluid just stopped working, is there an easy fix for this or should i take to dealer


If your rear wiper, fluid wash, and rear defrost stopped working at the same time try this first before taking it to the dealer. Start the 4Runner and lower the rear window glass. Wait a few seconds and raise the rear window. Turn the engine off and wait a few seconds. Restart the engine and see if this helps. I had the same problem after I had my drive belt replaced and the shop disconnected the battery cable. When the battery cable is disconnected it causes the rear wiper, fluid wash and defrost to stop working. Good luck!

Jan 16, 2010 | 2004 Toyota 4Runner

1 Answer

Rear Wiper Problem


Get a fine needle and try unblocking the jets in the outlet nozzle first

Jan 14, 2010 | 2007 Chevrolet Uplander LS Minivan

2 Answers

The rear wiper on my '99 model exped isnt working ,ford global says its the motor and it will cost me P13k . any one who can help me find a mechanic do some repair on this?


what is P13K?

check the fuse first. dealer can hook up NGS Tester and get fault codes to see what is wrong.

Principles of Operation
NOTE: The generic electronic module (GEM) will not activate the rear wiper system if either the liftgate or the liftgate glass is ajar. If either the liftgate or the liftgate glass becomes ajar while the rear wiper is in operation, the GEM will park the rear wiper motor.
There are two distinct modes of wiper operation:
  • Off Mode: In this mode, there is no rear wiper activity, and the wiper motor will be in the PARK position.
  • Interval Mode: This mode is selected when the rear wiper switch is in either the Interval 1 or 2 position. When this mode is selected, the rear wiper motor is driven up onto the glass by activating the rear wiper UP relay. When the wiper motor HIGH/LOW/PARK position input reaches the high position, the UP relay is deactivated and the DOWN relay is activated to reverse the wiper motor direction. When the wiper motor reaches the LOW position, as determined by the HIGH/LOW/PARK position input, the GEM deactivates the DOWN relay and will begin a new wiper cycle 1 to 10 seconds later, depending on the interval position selected.
To engage the rear window washer, rotate the rear window washer selector downward to the WASH position. The rear window wiper will run as long as the WASH position is selected. When the rear window washer selector returns to the OFF, INT 1 or INT 2 position, the washer will stop immediately, but the rear window wiper will continue for two to three sweeps and then return to its previous mode of operation.
The low washer fluid indicator chime warns that the washer fluid level is low. The low washer fluid indicator chime is a single tone with a duration of one second. The chime will sound when the low washer fluid indicator is initially activated.
The low washer fluid indicator warns that the fluid level in the washer reservoir is low. The low washer fluid indicator will illuminate when the washer fluid level is low and the ignition switch is in the RUN position.
The low washer fluid indicator will deactivate when the washer fluid reservoir is filled and the ignition switch has been cycled from RUN to OFF, then to RUN.
Inspection and Verification
  1. The wiper/washer system is a generic electronic module (GEM) controlled system; refer to Section 419-10 .
  1. Verify the customer concern by operating the wiper/washer system.
  1. Visually inspect for obvious signs of mechanical and electrical damage.


Visual Inspection Chart Mechanical Electrical
  • Hoses to windshield washer pump
  • Wiper linkage
  • Fuses 6 (5A), 8 (5A), 15 (5A), and 20 (5A)
  • Wiring harness
  • Loose or corroded connector(s)
  • Relays
  • Motors
  • Multifunction switch
  • Washer fluid level switch


----------------------------------------
  • The wipers are inoperative — rear
  • Fuses 6 (5A), 8 (5A), 15 (5A), and 20 (5A).
  • Circuitry.
  • GEM.
  • Multifunction switch (wiper/washer switch).
  • Rear wiper up relay.
  • Rear wiper down relay.
  • Rear wiper motor.

May 12, 2009 | 1999 Ford Expedition

1 Answer

Rear window wiper fluid placement


think it all runs off the main bottle in the front,but check for a panel either side at the back as it could have a seperate bottle

Feb 01, 2009 | 1997 Plymouth Voyager

Not finding what you are looking for?
2002 Chrysler Town & Country Logo

Related Topics:

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8548 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...