Question about 1999 Chrysler 300M

1 Answer

Installation procedure to replace cooling fan motor

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chrysler Master
  • 5,763 Answers

Remove upper crossmember then dicconnect fan connections next remove bolts holding fan to radiator now lift fans out, reverse to install.

Posted on Aug 25, 2010

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
jagjeffery
  • 318 Answers

SOURCE: replaced cooling fan relays,the cooling fan

remove the cooling fan relay you should have power on the pink and black wire and the solid red wire going to the base for the relay if you do then check then turn the a/c on and check for your ground sigal from the darkgreen and white wire if no ground you have a bad fan control module located on the right side of the engine compartment

Posted on Jun 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i get to the ac fan motor 2000 jimmy


  1. Disconnect the VCM or the PCM.
  2. Remove the coolant reservoir.
  3. Remove the rear coolant recovery reservoir mounting stud.
  4. Disconnect the cooling tube from the blower motor.

  1. Disconnect the electrical connector
  2. Remove the 5 blower motor and tan assembly mounting bolts
  3. Remove the blower motor and fan assembly
    Reverse procedure to install. Don't forget that cooling tube. It looks useless but is very important to reinstall.

Aug 15, 2012 | 2000 GMC Jimmy

1 Answer

About how long will it take to replace the radiator?


About 2.5 hours

Hope this helps, it it does please leave feedback and vote Thank You and Good Luck

  • Tools Required
  • J 38185 Hose Clamp Pliers
Removal Procedure

110563917

Caution: Before servicing any electrical component, the ignition key must be in the OFF or LOCK position and all electrical loads must be OFF, unless instructed otherwise in these procedures. If a tool or equipment could easily come in contact with a live exposed electrical terminal, also disconnect the negative battery cable. Failure to follow these precautions may cause personal injury and/or damage to the vehicle or its components.


  1. Remove the battery.
  2. Remove the air cleaner assembly.
  3. Drain the cooling system.
  4. Remove the right and the left engine mount struts. Refer to the following procedures:
    • Engine Mount Strut Replacement - Right
    • Engine Mount Strut Replacement - Left
    • Engine Mount Strut Replacement - Right
    • Engine Mount Strut Replacement - Left
  1. Use J 38185 to remove the inlet hose clamp from the radiator.
  2. Remove the inlet hose from the radiator.
  3. Remove the transmission oil cooler lines from the retainer clip at the bottom of the cooling fan shroud.
110563918


  1. Remove the bolt that connects the fan shroud to the condenser hold down bracket.
110563919


  1. Remove the cooling fan shroud bolts.
  2. Remove the coolant reservoir hose from the radiator overflow neck.
110563920


  1. Remove the radiator upper support brackets and bolts that connect to the fan shroud.
  2. Disconnect the engine cooling fan motors electrical connector.
  3. Remove the cooling fan motors electrical harness from the fan shroud clips.
  4. Remove the cooling fan shroud.
  5. Remove the bolt from the condenser tube support bracket to the radiator.
  6. Use J 38185to remove the outlet hose clamp from the radiator.
  7. Remove the outlet hose from the radiator.
  8. Disconnect the transaxle oil cooler pipes from the radiator.
  9. Tilt the top of the radiator rearward.
110564721


  1. Remove the condenser hold down bracket (1) from the radiator.
  2. Remove the air deflectors from the top of the radiator.
  3. Lift the condenser from the mounting tabs on the radiator (2). Position the condenser aside.
  4. Remove the radiator.

Jan 02, 2011 | 2004 Chevrolet Impala

1 Answer

How to remove blower motor


Try this procedure...

1. Disconnect the negative battery cable.
2. Remove the instrument panel (IP) storage compartment.
3. Remove the front screw from the right door sill plate.
4. Remove the right hinge pillar trim plate.
5. Disconnect the electrical connectors from the blower motor, as necessary.
6. Remove the bolt from the right lower IP support.
7. Remove the blower motor cover.
8. Remove the motor cooling tube.
9. Remove the blower motor flange screws and ferrules.
10. Perform the following steps in order to remove the blower motor:
Carefully pull the blower motor forward in order to avoid distorting the blower motor fan.
If necessary, pry back the right side of the IP.

11. Inspect the blower motor terminals for distortion.
12. Clean corrosion from the terminals as necessary.
13. Replace the blower motor as necessary.
14. Inspect the flange of the blower motor for damage or distortion that may cause an air leak.
15. Repair the flange as necessary.
16. Inspect the blower fan for any damage and distortion.

zjlimited_239.jpg

Fig. Pull the retaining tab down while turning the blower motor counterclockwise in order to disengage the blower motor

To install:

1. Guide the blower motor and blower fan into position. Be careful in order not to catch the blower fan on any protruding components.
2. Install the blower motor flange ferrules and screws. Tighten the blower motor mounting screws to 20 inch lbs. (2.1 Nm).
3. Install the blower motor cooling tube.
4. Install the blower motor cover.
5. Install the bolt to the right lower IP support.
6. Install the electrical connectors to the blower motor, as necessary.
7. Install the right hinge pillar trim panel.
8. Install the front screw into the door sill plate.
9. Install the instrument panel storage compartment.
10. Install the negative battery cable.
11. Verify the circuit operation.


Hope helps.

Dec 14, 2010 | 1999 GMC Yukon Denali

1 Answer

How to change a radiator


1988–91 Models
  1. Disconnect the negative battery cable.
  2. Properly drain the cooling system into a suitable container.
  3. Disconnect the fan motor and motor connector.
  4. Disconnect the upper and lower radiator hoses.
  5. Disconnect and plug the automatic transaxle cooling lines at the radiator, if equipped.
  6. Disconnect the coolant reservoir overflow hose.
  7. Remove the radiator attaching bolts and brackets.
  8. Remove the radiator with the cooling fan attached.
  9. Remove the cooling fan and shroud from the radiator. NOTE: Check all cooling system hoses for any signs of damage, leaks or deterioration and replace if necessary. To install:
  10. Attach the cooling fan and shroud to the radiator and install the assembly.
  11. Attach the radiator bolts and brackets. Tighten the radiator bracket bolts to 7 ft. lbs. (10 Nm).
  12. Connect the coolant reservoir overflow hose.
  13. Connect the automatic transaxle cooling lines to the radiator, if equipped.
  14. Connect the upper and lower radiator hoses.
  15. Connect the fan motor and thermo-switch wire connector.
  16. Refill the system with the proper type and quantity of coolant, check for leaks and bleed the cooling system.
  17. Reconnect the negative battery cable. Fig. 7: Cooling system components — 1988–91 engines 86833085.gif
1992–95 Models
  1. Disconnect the negative battery cable.
  2. Properly drain the cooling system into a suitable container.
  3. Disconnect the fan motor and motor connector.
  4. Disconnect the upper and lower radiator hoses.
  5. Disconnect and plug the automatic transaxle cooling lines at the radiator, if equipped.
  6. Disconnect the coolant reservoir overflow hose.
  7. Remove the radiator attaching bolts and brackets.
  8. Remove the radiator with the cooling fan attached.
  9. Remove the cooling fan and shroud from the radiator. NOTE: Check all cooling system hoses for any signs of damage, leaks or deterioration and replace if necessary. To install:
  10. Attach the cooling fan and shroud to the radiator and install the assembly.
  11. Attach the radiator bolts and brackets. Tighten the radiator bracket bolts to 7 ft. lbs. (10 Nm).
  12. Connect the coolant reservoir overflow hose.
  13. Connect the automatic transaxle cooling lines to the radiator, if equipped.
  14. Connect the upper and lower radiator hoses.
  15. Connect the fan motor and thermo-switch wire connector.
  16. Refill the system with the proper type and quantity of coolant, check for leaks and bleed the cooling system.
  17. Reconnect the negative battery cable. Fig. 8: Cooling system components — 1992–95 engines 86833086.gif
prev.gif next.gif

Aug 27, 2010 | 1991 Honda Civic

1 Answer

Need instructions on how to replace the cooling


Removal & Installation To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Radiator upper crossmember
    • Fan motor electrical connector
  3. Drain cooling system below the level of the upper radiator hose.
  4. Remove or disconnect the following:
    • Upper radiator hose from radiator
    • Radiator fan fasteners and upper clip
    • Fan assembly by lifting upward to clear radiator
To Install:
  1. Install or connect the following:
    • Radiator fan assembly
    • Upper clip and fasteners
    • Upper radiator hose to radiator
    • Fan motor electrical connector
    • Radiator upper crossmember
  2. Fill cooling system.
prev.gif next.gif

Jul 17, 2010 | 2004 Dodge Intrepid

1 Answer

I replace the fan clutch and i still have the code p1481 what does that mean? 2002 chevrolet Trailblazer 4.2 Thanks You! Arthur Tyler


TSB#05-06-02-012B: Service Engine Soon (SES) or Check Engine Light On, DTC P0480, P0526/P1481/P1484 Set (Replace Engine Cooling Fan Wiring Harness) - (Oct 19, 2006)
Subject:
Service Engine Soon (SES) or Check Engine Light On,
DTC P0480/P0526/P1481/P1484 Set (Replace Engine Cooling Fan Wiring Harness)
Condition
Some customers may comment that the Service Engine Soon (SES) or Check Engine light is illuminated. This condition may be intermittent and upon investigation, the technician may find either DTC P0480, P0526, P1481 or P1484 set.

Cause
This condition may be caused by the cooling fan harness chaffing against the plastic guide it routes through. This
contact may damage the insulation of the wires enclosed in that harness.

Correction
Replace the engine cooling fan harness using the procedure listed below.

1. Remove the cooling fan. Refer to the Cooling Fan and Shroud Replacement procedure in the Engine Cooling sub-section of SI.

2. Place the cooling fan assembly on a bench.
Disconnect the harness electrical connector from the cooling fan clutch.

3. Remove the harness from the plastic guide while feeding the wires out of the slot.

4. Before installing the new harness, wrap the affected area on the wires with electrical tape to keep the protective sleeve in place. Be sure to keep the tape approximately 25 mm (1 in) away from the connector so the wires can be fed into the slot.

5. Feed the wires into the slot and install the harness to the plastic guide.

6. Connect the harness electrical connector to the cooling fan clutch.

7. Install the cooling fan. Refer to the Cooling Fan and Shroud Replacement procedure in the Engine Cooling sub-section of SI.

Part Number 89024920

Description
Harness Assembly, Engine Cooling Fan Wiring
Thank you for using fixya.

Apr 29, 2010 | 2003 Chevrolet TrailBlazer

1 Answer

How to replace a blow fan motor on 2000 maxima


7f1b374.gif
Exploded view of blower and cooling unit

54c53c2.gif
Removing blower and cooling unit

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Discharge the A/C system.
  3. Disconnect or remove the following:
    • Negative battery cable.
    • Two refrigerant lines from the engine compartment

    NOTE Cap the A/C lines to prevent moisture from entering the system.

    • Glove box and mating trim
    • Thermal amp connector
    • Intake sensor connector
    • Fan control amp, blower motor connector
    • Blower motor and cooling unit
    • Separate the blower and cooling unit case, remove evaporator
    • Three bolts and motor from blower case
  4. To install, reverse removal procedure.
  5. Recharge A/C system.

Jan 04, 2010 | 2000 Nissan Maxima

1 Answer

Want to replace the radiator on my 1997 ford thunderbird


Radiator Aluminum Core, Crossflow — 3.8L (Base) and 4.6L Engines
Removal
  1. Drain engine cooling system as described. Disconnect upper radiator hose (8260) and lower radiator hose (8286) and radiator overflow hose (8075) from the radiator (8005). Disconnect the transmission oil cooler inlet and outlet lines from the radiator.
  1. Remove cooling fan motor,fan blade (8600) and fan shroud (8146) assembly as described.
  1. Remove radiator upper bracket retaining bolts and remove bracket. Lift radiator from vehicle.
Installation
  1. Position the radiator into the vehicle. Install upper brackets and tighten bolts securely.
  1. Connect the transmission oil cooler lines to the transmission oil cooler fittings.
  1. Install cooling fan motor, fan blade and fan shroud assembly as described.
Engine Cooling Fan Motor, Fan Blade and Fan Shroud Assembly, Electrical Removal
  1. Disconnect (pull apart) the male-female cooling fan motor wiring connector at the side of the fan shroud (8146). Remove the male terminal connector retaining clip from the fan shroud mounting tab.
  1. Remove two fan shroud upper retaining bolts at the radiator tanks.
  1. Lift cooling fan motor/fan blade (8600)/fan shroud assembly past radiator (8005), disengaging fan shroud from two lower retaining clips.
Installation
  1. Follow removal procedure in reverse order.
  1. Tighten fan shroud retaining bolts to 5.2-7.2 Nm (46-63 lb-in).

  2. 10e2638.gif
    8d231fe.gif HOPE THIS HELPS.

    Oct 30, 2009 | 1997 Ford Thunderbird LX

    1 Answer

    How to change water pump (1997 sonoma)


    The text below is from the GM Service manual 4.3L V6 Engine
    Water Pump Replacement (4.3L)
    Removal Procedure
    Drain the cooling system. Refer to Draining and Filling Cooling System .
    Loosen the water pump pulley bolts.
    Remove the cooling fan and clutch assembly.

    Tools Required
    J 46406 Fan Clutch Wrench

    Removal Procedure
    Remove the upper fan shroud.
    Remove the fan clutch from the water pump in a counterclockwise direction using the J 46406 .
    Remove the fan clutch assembly.
    Remove the drive belt. Refer to Drive Belt Replacement Remove the water pump pulley mounting bolts.
    Remove the water pump pulley.
    Remove the radiator outlet hose clamp from the water pump.
    Remove radiator outlet hose from the water pump.
    Remove the water pump mounting bolts.
    Remove the water pump from the engine.
    Remove the water pump gaskets.
    Clean the water pump gasket mating surfaces.
    Installation Procedure
    Install the water pump gaskets.
    Install the water pump to the engine.
    Apply a sealer (GM P/N 12346004) to the bolt threads.
    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
    Install the water pump mounting bolts.
    Tighten
    Tighten the mounting bolts to 41 N·m (30 lb ft).
    Install the radiator outlet hose to the water pump.
    Install the water pump pulley.
    Install the water pump pulley bolts.
    Tighten
    Tighten the water pump pulley bolts to 25 N·m (18 lb ft).
    Install the drive belt. Refer to Drive Belt Replacement in Engine Mechanical - 4.3L.
    Install the fan clutch assembly.
    Fill the radiator cooling system. Refer to Draining and Filling Cooling System .
    Inspect the cooling system for leaks.

    Oct 01, 2009 | 1997 GMC Sonoma

    1 Answer

    Need to replace the left rad fan motor, any ideas on how to do it if i have the new part?


    1. Remove radiator from vehicle.
    2. Remove fan shroud retaining bolts, and cooling fan motor/blade/shroud assembly.
    3. Remove fan blade retaining clips and blades.
    4. Remove motor mounting screws and motors.
    5. If necessary, remove Constant Control Relay Module (CCRM).
    6. Reverse procedure to install. Torque CCRM screws to 40-56 in lb, and shroud retaining bolts to 24-48 ft lb.

    May 27, 2009 | 1996 Lincoln Continental

    Not finding what you are looking for?
    1999 Chrysler 300M Logo

    Related Topics:

    112 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chrysler Experts

    yadayada
    yadayada

    Level 3 Expert

    77544 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22306 Answers

    chargerhp
    chargerhp

    Level 3 Expert

    814 Answers

    Are you a Chrysler Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...