Question about 1997 Plymouth Grand Voyager

1 Answer

I have a 1998 voyager, once in awhile all the insturment panels will go off, then it won't stay running. I tried everything, nothing helps. I even had the alarm reset, and had to buy a new alarm remote. It ran good for about a month or so. then it happened again. When I hit the dash board, it won't start at all.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Plymouth Master
  • 5,763 Answers

You may have a bad cluster, check the battery connections at the battery and most important check power cable to the fuse/relay box in engine compartment, you will see where cable goes to a stud and nut, there it corriods,

Posted on Aug 25, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Signal lights in front won't work


As someone who has had fun with a right rear light panel on a toyota corolla I can sympathize. I went in to the shop and the guy replaced 3 bulbs on mine. Did yo fix the left signal light yet?

Jul 14, 2012 | 1998 Plymouth Voyager

1 Answer

1998 Plymouth grand voyager ignition won't turn


I have had this happen on my 98 Voyager. Just have a new key cut. This new key will sometimes cure the problem. The older keys get worn out and won't unlock the ignition. Try this before a much more expensive and time consuming change of the ignition.

Nov 01, 2011 | 1998 Plymouth Voyager

1 Answer

My jeep won't start unless I give it gas. It used


Did you clean the throttle body and plate of any carbon ?

Aug 27, 2017 | 1998 Jeep Grand Cherokee

2 Answers

Guages and insturment panel stopped working on a 1998 plymouth


In the event that you have not completely fixed this problem, I suggest the following: Do a google search for "98 voyager instrument cluster solder" and you will find an abundance of posts regarding the soldered joints on the main terminal connector on the back of your instrument cluster. If the behaviour is at all erratic and unpredictable, or hitting the dash makes the gauges come back to life, then you are about 99.9% sure it is the solder problem. It takes about 8 minutes to remove the instrument cluster (okay maybe 15), and about 2 minutes to remove the circuit board. By examining the solder joints of the main connector with a magnifying glass, you will probably see cracked or corroded solder on them. Briefly reheat each solder joint with a soldering iron to re-flow the solder. Your erratic gauge behaviour should now be history.

May 25, 2009 | 1998 Plymouth Voyager

1 Answer

I have a 1998 plymouth voyager and the insturment panel and gauges and wipers and locks stopped working how could this be fixed


you have to replace the " body control module " located under dash drivers side. and most of time they have to be reprogrammend unless you buy it new from dealer and they do it before you get it. the body control mod controls all those items and go bad alot.

May 25, 2009 | 1997 Plymouth Voyager

1 Answer

1998 chry. t&c lxi,runs great but once in awhile when you go to start it , it will start but stall like it ran out of gas it will do this for approx. 3 tries then there is nothing ,turn the key and...


I have a 97 van and same thing is happening. Won't stay running and the next day - starts right up. I just read that the gauge pod/instrument cluster which is basically a module itself needs replaced - it's in the dashboard. After removing the cluster, you will find a couple of pc boards on the back. The pc boards and the solder connections become damaged after years of hot and cold weather. The solder joints will either crack or become loose from the expansion and contraction of hot and cold conditions. You can re-solder all the jointws and carefully reheat each one, or get a used one from a junk yard or auto parts store or dealership. Just take out the old one and plug in the replacement and reinstall the dashboard parts. I have not tried it yet, but I am going to. I have also heard that if you disconnect the battery cables for awhile, which allows the computer to restart, the car will stay running at least for awhile until you can repair it.

Hope this helps.
DB

Jun 28, 2008 | 1998 Chrysler Town & Country

Not finding what you are looking for?
1997 Plymouth Grand Voyager Logo

Related Topics:

134 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...