Question about Ford Mustang

1 Answer

I have a 1964 1/2 mustang that the starter showers sparks when the engine is started and running. The starter was replace a few days ago and has been tested as working. I was told that a spacer is needed. What is the problem and how can I fix it?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Sounds like its shorting out or the hot wire is rubbing somethimg metal

Posted on Aug 25, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ford mustang tries to start but will not continue running. We checked the battery, spark plugs, starter, and alternator. We believe the problem is either with the fuel pump driver module or the pump...


try spraying starting fuid into the throttle body and see if it runs then for a few seconds. If yes, check fuel pressure. It should be 34 psi with engine running, 40 psi key on engine off. More liley th pump in the fuel tank.

Sep 08, 2011 | 2001 Ford Mustang

1 Answer

Engine will not start,fuel pressure ok,no spark and no injection pulse.sensors check out ok.problem appeared few weeks ago after aborted start.after disconnecting battery and reconnecting after a while...


Try first checking all the connections, then if you can try to use a different battery just to make sure that the battery is still working fine and check also the starter ,becase this can be a problem also with the starter solenoid that may need repair or replacement...

Hope that helps.........

Sep 19, 2008 | Audi A6 Cars & Trucks

1 Answer

2005 Mustang GT idleing problem


may be it the problem of another throttle body.also check the ignition switch.

Check all of the battery terminals and cables and check the wires on the starter/selonoid, start from the battery and follow the cable out and check all conections , clean and tighten them and if it still does it the starter/selonoid is bad and needs replacement...

Aug 25, 2008 | 2005 Ford Mustang

1 Answer

My 98 mustang has what seems to be good crank but wont start, it will start and run good if i spay starter fluid in it. this problem comes and gose from one day to the next. what do you thin?


if it runs when spraying starting fluid in it, then the most likely problem is no fuel getting to engine. check or replace fuel filter, check the fuel pump fuse and relay it may have blown. if not that see if fuel pump is working. to check pump--- have someone turn car to on, while you feel for vibration at fuel tank under car. a fuel pump only comes on for a few seconds to get the fuel to engine. but when started it runs continuously. have a good day !!

Jan 03, 2011 | 1999 Chrysler 300M

1 Answer

Need a wiring diagram for 1986 ford mustang 4cyl engine. Helping a friend with his 4cylinder mustang and when i installed the negative terminal on the battery then as i place the positive terminal it...


Hi!!

You may have the positive cable hooked in the wrong side of the starting selenoid or the starter selenoid is defective.

Follow the RED (+) cable from the battery, it goes to the starter selenoid wich has two terminals, change the cable to the other terminal, that should take care of the problem unless the selenoid is stuck on. Replacement runs about $15.

Don't forget to rate this post. Good Luck!!

Jul 06, 2010 | 1986 Ford Mustang

1 Answer

1964 1/2 mustang beinig rebuilt. A new 302 engine


That's because the 302 and the 260 don't share the same accessory bolt patterns. If it's a dealer installed AC the mounting may be "custom". If you still have the original engine, transfer the bolt hole positions, drill and tap. Good luck. Measure twice!

Sep 30, 2009 | 1965 Ford Mustang

1 Answer

I have a 65 mustang 200 engine. After changing


Make sure you were given the right plugs for the car (correct heat range) also check the choke plate after the car warms up to ensure the choke plate is all the way open.

Jul 10, 2009 | 1965 Ford Mustang

1 Answer

Engine skipping/misfiring, engine light flashing


Drive it into a dark place, or wait till dark. When it's running poorly, see if you can see any spark flying around. It sounds like plug wires.

Mar 04, 2009 | 1995 Mazda Millenia

1 Answer

2005 V6 Mustang


check for fuel, spark and compression. these are the only things needed for a engine to run

Feb 08, 2009 | 2005 Ford Mustang

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...