Question about Dodge Pickup

Open Question

Looking for windshield wiper grommets for a 1990 dodge 150 pick-up.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

losthorse702
  • 1 Answer

SOURCE: Windshield wiper arm disconnected

I can not get the wiper arms off my 86 dodge ramcharger!!!

Posted on Mar 27, 2009

  • 192 Answers

SOURCE: can't find fuse box for horn,turning signal and windshield wiper

I looked this up on WikiAnswers. Apparently the 2005 dodge magnum has 2 fuse boxes. One is under the hood on the passenger side and the other is in the trunk, next to the battery, in the spare tire storage well.

Posted on May 11, 2009

  • 1 Answer

SOURCE: 2001 Ford F 150--Windshield wipers electric

You need to check your Fuses.. It sounds like you blew a fuse that controls Those Items..

Posted on Jun 18, 2009

  • 3600 Answers

SOURCE: 1990 dodge ram pickup wiper stopped working. Motor

First you have to remove the metal caps covering the wiper blade locking nut then remove the nut and leftthe wiper arm assembly up and rock back and forth till loose. then pull arm off as you wiggle the arm. next raise the hood and remove the 4 inside screws at the back of the hood remove the valance and the 2 plastic holding clamps then lift up. Once you have valance off look to see if the gears are stripped on the motor or the shaft if they are go to a junk yard and buy new parts. you will find the short rod and a long rod, they should be connected, if not the ball on the end of the long rod may have poped out turn on key then wiper motor and watch the parts move. You will be able to see it right away.
Hope this helps. If you need more asstance please post here and thanks for using fix-ya
Avid101

Posted on Aug 23, 2009

  • 2 Answers

SOURCE: Windshield wipers don't work but the motor runs . 93 Dodge Dakota

remove wiper arms and then you can raise the hood to remove screws that hold down the vent panel.
now carefully remove vent panel.

Posted on Jan 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the wiper motor relay switch on a 1990 plymouth voyager v6?


wipers won't work??? - CarGurus

www.cargurus.com > Questions > Chrysler > Town & Country

CarGurusFeb 15, 2012 - 1998 Chrysler Town & Country LXi My windshield wipers won't work. The turn ... I have a Plymouth Horizon & the same problem, but I'm fairly sure it's theswitch on mine. ... Ended up taking it to the dealership - it was a wiring problem from the body control module to the switch. ... Used Dodge Caravan".

Auto Repair : How to Test a Windshield Wiper Motor ...

? 3:04
https://www.youtube.com/watch?v=7EliY2Hwj0E
May 12, 2009 - Uploaded by ehowauto
In order to test a windshield wiper motor, the first thing to do is to make ... He said its the relay and the entire ...

Windshield Wiper Motor Replacement : How to Access a ...

? 3:37
https://www.youtube.com/watch?v=iVBAvvfc1FU
Oct 1, 2008 - Uploaded by expertvillage
Removing windshield wiper arms and intake grading is essential to gaining access to the windshield wiper

Jan 27, 2016 | Plymouth Cars & Trucks

1 Answer

How to install a windshield wiper motor in a 1996 dodge dekota sport


Pull off cowl (grated panel where wiper arms come out of. Pop off grommets from motor to wiper linkage unplug & unbolt motor. I had several of those trucks the job can be done in less than 30 minutes.

Feb 16, 2013 | Cars & Trucks

2 Answers

Windshield wipers are not working, motor is running but blades are not moving


You probably need to replace the plastic grommets on the wiper linkage arms. On your Dodge there are 2 linkage arms that connect the wiper blade arms to the motor. What has likely happened is the plastic grommet on the motor shaft wore and the linkage arm fell off. As Dodge used several different configurations for the actual set up, you'll need to refer to a repair manual ( Chiltons, Haynes, Motor, etc.)for the specifics on affecting the repair. I have learned it is best to replace ALL of the plastic grommets and not just the 1 that let loose and sometimes it is easier to just buy a replacement arm with the grommets installed. When you go to install the grommet, grease lightly the inside of it with dielectric grease to ease installation as I have broken grommets trying to push them on the motor shaft dry.
If you don't have access to a repair manual you can go to
www.alldata.com
and pay a fee for the diagrams and specific instructions which you can also print out for future reference. I had an 83 charger that had an access panel on the top of the firewall in front of the driver under the hood to get to the wiper motor and linkage, so looking around there may help you before you buy any info to help. Also pay close attention to which way the fat side of the grommet is on the linkage arm - you could put it on backwards and it will fall off when you try to use it. This led to many fun times for me before discovery!!
Hope this helps!!

Nov 29, 2010 | 1989 Dodge Dynasty

1 Answer

Where is the windshield wiper motor on a 2007 Dodge Caravan and how do I replace it?


Wiper Motor: Service and Repair
Removal
REMOVAL
The front wiper motor comes as a unit with a wiper pivot on each end and mounts to a shaft that holds these two inner pivots.
1. Disconnect and isolate the battery negative cable.
2. Remove the wiper arms.
3. Disconnect the washer hose at the in-line connector located near the air cleaner housing.
4. Lift the cowl grille and disconnect the washer hose grommet from the hole in the wiper module. Pull the washer hose and the grommet
completely through the wiper module tub hole.
5. Remove the cowl grille.
CAUTION: Be careful not to scratch the cowl grille on the corner of the hood.
6. Remove the four brace nuts holding the wiper tub to the lower windshield fence.
7. Remove the four bolts underneath the wiper tub inner brace holding the tub to the bulkhead.
8. Remove all four inner support brace mounting nuts and pull the inner braces just free of the mounting studs.
NOTE: The wiper tub will drop down slightly.
9. Disconnect the driver and passenger side wiper link ends at the inner pivots.
10. Remove the two left wiper motor assembly mounting nuts.
11. Remove the two right wiper motor assembly mounting nuts.
12. Partially lift out the wiper motor assembly out of the wiper tub.
13. Disconnect the wiper motor electrical connector.
14. Remove the wiper motor assembly the rest of the way from the wiper tub and remove from vehicle.
--------------------------------------------------------------------------------------------
Wiper Motor: Service and Repair
Installation
INSTALLATION
1. Install front wiper motor assembly onto wiper tub.
2. Connect the electrical connector to the front wiper motor assembly.
3. Install the four mounting nuts. Tighten nuts to 9 Nm (80 in.lbs.).
4. Push the four inner support braces onto the studs and install the four nuts. Tighten the nuts to 9 Nm (80 in.lbs.).
5. Install the four bolts underneath the wiper tub inner braces that hold the wiper tub to the bulkhead. Tighten the bolts to 17 Nm (150 in.lbs.).
6. Install the four nuts holding the wiper tub to the lower windshield fence line. Tighten nuts to 7 Nm (65 in.lbs.).
7. Apply grease to drive link bushings.
NOTE: Make sure to use Mopar(R) approved grease.
8. Attach the driver and passenger side outer wiper linkage to the inner pivots on the front motor assembly and firmly snap into place.
CAUTION: Do not apply too much force to engage link bushing or damage can occur to the drive link bushing.
9. Position the cowl grille in place.
10. Install the washer hose and grommet into the wiper tub.
NOTE: Be sure to properly seat the washer hose grommet into the bottom of the wiper tub.
11. Connect the washer hose at the in-line connector located by the air cleaner housing.
12. Install the cowl grille.
CAUTION: Be careful not to scratch the cowl grille on the corner of the hood.
13. Connect the battery negative cable.
14. Verify that the wiper motor is in the Park position by cycling the wipers system. When done, remove keys from ignition.
15. Install the wiper arms.
16. Align the wiper arms and tighten nuts to 35 Nm (25 ft.lbs.).
17. Install the wiper arm nut caps.

f7c141f.jpg

Sep 13, 2009 | 2007 Dodge Caravan SXT Minivan New Cars

1 Answer

The windshield wipers are stuck vertically and now


This sounds like the wiper motor has failed. You can pick one up at the local parts store. If not mechnically savvy, I would recommend taking to shop for working in tight areas that these can be. But, otherwise, the motor is on the fire wall, unplug, remove screws(4), exchange with new, and reassemble as removed. I hope this helps.

Aug 07, 2009 | 1997 Dodge Grand Caravan

1 Answer

I have a 1992 dodge shadow.but the windshield wipers isn't working.I checked the motor is well,the terminal voltage is 12V,how can I continu to repair the 1992 dodge shadow's windshield wipers?


You posting is slightly confusing but I gather your windshield wipers stopped working.
The repair method is as follows;
) Check the fuse.
) Check the wiper motor. Turn the wipers on and listen for the hum of the motor.

If you hear the hum then the linkage has probably come loose. You will have to take the covers off
to get to the linkage for the wiper. You can either repair the parts, get salvage yard parts or replace with new part$.

If you do not hear the motor hum then you should verify electricity is getting to the motor. A simple
voltmeter can be used. If the motor is bad you can replace it. Call some auto supply stores for after-market motors or call salvage yards for parts.

May 07, 2009 | 1990 Dodge Shadow

2 Answers

Front Windsheild Wipers


I have 2007 only. please rate as solved if this is what you needed. good luck.

SECTION 501-16: Wipers and Washers 2007 Freestar/Monterey Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 04/27/2006
Wiper Motor — Windshield s7w~us~en~file=adobe.gif~gen~ref.gif Printable View (104 KB) Removal
  1. Remove the windshield wiper arms.
  1. NOTE: Disconnect the washer hose before removing the cowl panel grille.
    Remove the pushpin-type retainers and the cowl panel grille.
  1. Remove the washer hose grommet from the cowl panel and position aside the washer hose.
  1. If equipped, remove the A/C air inlet filter.
  1. Remove the 9 cowl panel bolts and position aside the cowl panel.
  1. Disconnect the windshield wiper motor electrical connector.
  1. Remove the cowl panel from the vehicle.
  1. Remove the 4 bolts and the windshield wiper motor.
    s7w~us~en~file=n0001518.gif~gen~ref.gif
Installation
  1. Position the wiper pivot arms on the windshield wiper motor and install the bolt.
    • Tighten to 15 Nm (11 lb-ft).
  1. Install the 3 windshield wiper-to-cowl panel bolts.
    • Tighten to 15 Nm (11 lb-ft).
  1. Position the cowl panel in the vehicle and connect the windshield wiper motor electrical connector.
  1. Install the washer hose and grommet in the cowl panel.
  1. Install the 9 cowl panel bolts.
    • Tighten to 6 Nm (53 lb-in).
  1. If equipped, install the A/C air inlet filter.
  1. Position the cowl panel grille in the vehicle and connect the washer hose.
  1. Install the pushpins.
  1. Install the windshield arms and nuts.
    • Tighten to 27 Nm (20 lb-ft).
  1. Cycle and park the windshield wipers to check for correct alignment.
3c6f4d5.gif
b8a2ebf.gif

Apr 09, 2009 | 2006 Ford Freestar

1 Answer

How do you get the wiper arms off of a 1998 dodge ram?


Wiper arms are generally held on one of two different ways. Either with a nut under a little cap that flips up above the pivot shaft, or a lock tab at the base of the wiper arm that pivots out and away a little from the pivot shaft. With either one, you will have to flip the wiper arms away from the windshield because they will not pull off the pivot shaft until the wiper blade spring tension is no longer acting against the windshield. Here's a pic of the lock tab.d76e2b6.jpg

Mar 14, 2009 | 1991 Dodge Ram 150

1 Answer

Dodge Caravan 1990 front Windshield Wipers Don't Turn on.


If the Fuses are good and the Rear Works the Cause will be the Wiper Motor for the Windshield Wipers. Please Rate My Response! Thanks!

Feb 04, 2009 | 1990 Dodge Grand Caravan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...