Question about 2006 Chrysler Town & Country

1 Answer

How do I change a blower motor in a chrysler Town and country

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 327 Answers

Hello, to change the blower motor resistor follow this steps:

  1. Disconnect and isolate the battery negative cable.
  2. Open the glove box.
  3. Flex both sides of the glove box bin inward near the top far enough for the rubber glove box stop bumpers to clear the sides of the glove box opening, then roll the glove box downward.
  4. Reach through the glove box opening to access and disconnect the instrument panel wire harness connector for the blower motor resistor from the resistor connector receptacle.Blower motor Resistor
  5. Reach through the glove box opening to access and disconnect the blower motor pigtail wire connector from the resistor connector receptacle.
  6. Remove the two screws that secure the blower motor resistor to the evaporator housing.
  7. Remove the blower motor resistor from the evaporator housing.

Thanks

Posted on Aug 25, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

A/C Blower Switch on chrysler----- Blower works in


Chrysler vehicles are notorious for the blower motor resistor going out. If your Town & Country has automatic climate control use a SMP RU399, else use an SMP RU362 for the front resistor and a SMP RU490 for the rear. They are generally located on top of the blower motor/wheel assemblies.

May 26, 2011 | 2003 Chrysler Town & Country

2 Answers

Blower will not blow air from front blower. Changed fuses still will not work. Does this mean blower motor is bad?


No, it's the blower motor resistor
Cost $13.99 at AutoZone
Fits behind the glove box
Two plugs, two screws and you're done!

Nov 22, 2010 | 2005 Chrysler Town & Country

1 Answer

2005 chrysler town and country van, driving down the street blower motor running fine. no noise, then just quit running. what may have happened?


Blower motor is hard to replace. Test it by putting 12 volts on the connector located under the passenger dash. Polarity doesn't matter.

Sep 09, 2010 | 2005 Chrysler Town & Country

1 Answer

2002 Chrysler Town and Country Rear Heat/Air only on High


most of the time the resistor is located downwind of the blower motor so it should be not to fao from the blower motor in the right rear of the van behind the quater trim panel which is the hvac unit is located

Jun 01, 2010 | 2002 Chrysler Town & Country

1 Answer

Where is the Blower Motor Resisitor located in a 2000 Chrysler Town and Country LXi? I checked behind the glove box and did not see the darn thing. Anyone? I have the part and was hoping for a quick fix.


It is under the dash by the blower motor on the passengers side.Just turn on the blower motor and follow the fan noise if it works.The resistor will be connected to the blower motor.Hope this helps.Good luck.

Feb 04, 2010 | 2001 Chrysler Town & Country

1 Answer

1996 town & country van front heater blower


you will need to start by checking fuse,then power to motor,then blower motor resistor

Jan 29, 2010 | 2005 Chrysler Town & Country

2 Answers

Air conditioner only works on high 99 chrysler town and country van we change the switch and the motor and it still doen't work on lower settings


you need a blower resistor maybe a blower motor also but the resistor is for speeds and it usually goes when the blower motor starts to draw too much power the resistor is outside under the cowl on the passanger side you may need a connector pigtail also the dealer will have what you need

Sep 21, 2009 | 1999 Chrysler Town & Country

1 Answer

Describe your 2002 Chrysler Town &


first i will do to change the blower motor resistor and see what happen it is near the blower motor and see if any wires burned out

Jul 14, 2009 | 2002 Chrysler Town & Country

1 Answer

Where is the front blower motor on a 2004 Town & Country located and how do you get to it?


Behind glove box, look for cover over motor. Disconnect battery negative (-) first & wait a few minutes, (to avoid accidental deployement of airbag)then remove glovebox, and then you'll have access to cover on blower motor. Remove it, then motor. Why are you changing it if you don't mind me asking?

Jun 10, 2009 | 2004 Chrysler Town & Country

1 Answer

Heat/ac blower motor


ce the resister for blower motor.

Jun 05, 2009 | 2001 Chrysler Town & Country

Not finding what you are looking for?
2006 Chrysler Town & Country Logo

Related Topics:

545 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...