Question about 2002 Ford Taurus

2 Answers

I have a 2002 ford taurus 3.0L v6 it will not start i replaced the starter and it seems like the starter is not getting any power what could it be ?

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Expert
  • 1,868 Answers

Hello! Using a voltmeter...Place the + probe on the White/Pink wire on the starter motor...The - probe to ground...Have someone turn the key to start...Should read +12 volts...Send a comment with results..............Guru............Saailer

Posted on Aug 25, 2010

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 118 Answers

Dead or weak battery, corroded or loose terminals, bad cable, bad solenoid (starter relay), bad ignition switch, bad neutral safety interlock, driver forgot to put car in park or neutral before starting, bad wiring. When you turn the key, do you hear anything, like maybe a clicking noise, or is the car completely silent?

Posted on Aug 25, 2010

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 33 Answers

SOURCE: Amps from a starter for 1989 Ford Taurus

Coming out? None
You should have a starter draw of about 250-300 amps during cranking. Disconnect the fuel or ignition system and crank for several seconds to get a good reading.

Posted on Nov 21, 2008

michigan man
  • 3533 Answers

SOURCE: Starter Replacement

yes it can the model 2000-to-2007are the same and i just wanted to tell you all of Michigan Man Cars are fords and to give you this website www.taurusclub.com its a good site also.

Posted on May 17, 2009

blueextc3221
  • 15935 Answers

SOURCE: need diagram of serpentine belt for 94Solution for "need diagram for replacing serpentine belt for 94 ford taurus gl w/3 0 v6 engine and a/c" ford taurus gl w/3.0 v6 engine and a/c

89beac5.gif Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

Posted on May 21, 2009

c17hydro
  • 2984 Answers

SOURCE: 2002 ford taurus wtaer pump

Removal & Installation 3.0L (2V) To Remove:

  1. Drain the engine cooling system.
  2. Loosen the water pump pulley.
  3. Remove the bolt and the nut and position the roll restrictor bracket out of the way.
  4. Remove the accessory drive belt.
  5. Remove the generator.
  6. Remove the bolt and the accessory drive belt tensioner.
  7. Remove the nut, the bolt and the support bracket.
  8. Remove the bolts and the water pump pulley.
  9. Disconnect the water pump inlet hose and the crankshaft position sensor electrical connector.
  10. Remove the bolts and the water pump, and clean the sealing surfaces
To Install:
  1. Install the water pump. Tighten bolts in the sequence shown:
    1. Tighten numbers 1-7 to 18 ft.-lbs. (25 Nm)
    2. Tighten numbers 8-12 to 89 in.-lbs. (10 Nm)
    3. Connect the crankshaft position sensor electrical connector and the water pump inlet hose
    4. Install the support bracket.
    5. Install the accessory drive shaft tensioner.
    6. Install the generator.
    7. Install the roll restrictor bracket, bolt and the nut.
    8. Install the water pump pulley.
    9. Install the accessory drive belt.
    10. Connect the battery ground cable.
    11. Fill the engine cooling system.

9de9feb.gif
Water pump bolt torque sequence (3.0L (2V) engine)

Posted on Jul 04, 2009

  • 95 Answers

SOURCE: po443 code 2002 ford taurus

That code is for the Evaporative Emissions. It could be a bad Evaporative Emissions Canister Valve or just a bad vacuum line or my granddaughter's 1997 Ford Escort had that code and her gas cap was NOT on. Now when you figure out what one it is disconnect the battery for 10 minutes to reset the computer.

Posted on Jan 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

New battery & starter. Car wont start. Starter clicking.


sounds like solenoid has failed or is sticking

Jan 08, 2015 | 2002 Ford Taurus

1 Answer

Starter attempts to re-engage after already running


I agree with Ignition switch diagnosis. Another possibility is a short in the lockout for the gearshift and brake pedal lever. This is suppose to stop you from starting the vehicle unless your foot is on the brake pedal. These get smashed and it should not allow power to go to the starter relay, but if they do cross the circuit, it may provide power to the starter relay. You did not say if the starter tried to engage when you tried to shift from Park.

I think the Ignition switch is the most likely, but I wanted to mention the crushed lockout switch as a remote possibility.

Mar 29, 2014 | 2001 Ford Escape

1 Answer

Do 2002 ford Taurus 24 valve v-6 have a starter relay mounted on the firewall?


I don't think so. The starter has a solonoid on it. There isn't a relay involved. Check for power at the small wire on the starter when the key is in the "start" position. If there is power there ,the starter is bad. If not,could be neutral safety switch or ignition switch.

Sep 24, 2013 | 2002 Ford Taurus

2 Answers

Can't get the starter out of a ford Taurus 2004


either you took out the wrong bolt by the trans.... or the pin is stuck ... give it a whack with a mallet
should of taken out 2 ,13 mm bolts

Jul 28, 2011 | 2008 Ford Taurus X

1 Answer

2002 Ford Taurus-won't start, replaced starter last night, started once, but hasn't since. Battery is good. Any ideas?


Have you thought of maybe checking the ignition switch that starts your vehicle. A faulty ignition switch will give you the same symptoms as a dead battery or a faulty starter. I hope this helps you out.

Mar 31, 2011 | 2002 Ford Taurus

1 Answer

Need a picture of the serpentine belt diagram


2002 FORD TAURUS - V6 3.0L 182ci FLEX FI N 2
and
2002 FORD TAURUS - V6 3.0L 182ci GAS FI N U

a9ea5b9.jpg


2002 FORD TAURUS - V6 3.0L 182ci GAS FI N S

568acc8.jpg


Other details in DAYCO Catalogue.

Hope this help (remember rated this).

Mar 25, 2010 | 2002 Ford Taurus

2 Answers

My 2002 Ford Taurus will not start. When i turn


check your battery and charging system. take your battery out and go have it tested. once a good battery is in place, have the charging system tested and make sure you have sufficient charge(13.3-14.5v is standard).its getting cold out there people and batteries tend to fail now most of all because of how we treated them in the summer.

Nov 08, 2009 | 2002 Ford Taurus

2 Answers

Car will not start.


Next step is checking the battery, or replacing it.
After that, check that the 'security' key or whatever is used on that vehicle isn't messed up. Might be a fuse for that as well.

Jun 22, 2009 | 2002 Ford Taurus

Not finding what you are looking for?
2002 Ford Taurus Logo

Related Topics:

213 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...