Question about Ford F-150

1 Answer

What do i do when the hydraulic cluch wont move from the floor board to get the engine started.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 7,689 Answers

System has a leak--must be repaired and bled

Posted on Aug 25, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Clutch problem


I would think you have a hydraulic clutch, so there should be a return spring on the pedal or the master cylinder.

Jan 29, 2014 | Subaru Cars & Trucks

1 Answer

Cluch pettle dont work just go to floor


Either the upper or lower clutch kit is leaking hydraulic. Replace the clutch kit. You may as well check if the clutch fluid reservoir is not empty of fluid.

Dec 22, 2012 | 1994 Isuzu Rodeo

1 Answer

Cluch falls to the floor board


Most likely a hydraulic operated clutch. The master or slave has failed, you need to figure out which and replace it, then bleed the system. Generally there will be a stain of leaked hydraulic (same as brake) fluid as a clue to which failed. Having a short rope attached to the clutch pedal will assist in pulling it back up during the bleeding process.

Feb 22, 2011 | 1995 Nissan Pickup

2 Answers

The hydraulic clutch stopped working.It won't shift.There is no pressure on the clutch whne you push it down.


The clutch hydraulic system is very small. Check the resevoir is full. If empty fill. Try clutch. Still problem ? Bleed the clutch slave cylinder at the trans bleeder. You dont bleed this clutch like brakes pumping up several times. Have someone push clutch to the floor and hold it there, then you open and close bleeder while keeping pedal to the floor. Check the fluid level every time you open/close the bleeder as this system is so small and will empty quick.

Nov 16, 2010 | 1994 Mazda 2WD B Series Pickup

1 Answer

1989 jeep wrangler cluch pedle goes to floor


These jeeps have an hydraulic system with a master cylinder up top and a hydraulic line leading down to a slave cylinder. You likely have a leak somewhere and your hydraulic fluid is gone.

Sep 09, 2010 | 1989 Jeep Wrangler

1 Answer

Geo sick..lol have to push cluch to floor few times to get it to start..lost 1st an 4th gear they pop out and is slow to nothing taking off in 2nd..push gass but get rev no go..lol some one said the boot...


3 cylinder Metros use a mechanical cable not disengage the clutch, not a hydraulics so there is no 'boot' that could be bad (a "boot" is a common name for the rubber seal in a hydraulic master/slave cylinder). There is an electric safety switch under the dashboard, at the top of the clutch pedal which prevents the engine from turning over unless the clutch pedal is depressed. It is likely faulty or adjusted incorrectly.

Jan 17, 2010 | 1995 Geo Metro

2 Answers

Wont shift into gear


Was the fluid low? Does the pedal have any resistance? does it feel normal? Did it happen all of a sudden? Does it shift into gear with the engine off? You say it doesnt shift into gear, but does the shifter move into gear or not? Or it does and the truck wont move? Sounds like maybe the SLAVE CYL isnt operating? leaking? theres more questions to answer.

Dec 30, 2009 | 1988 Toyota Pickup

1 Answer

I put my car in drive and it wont move but if I put it in reverse it goes, what could be the problem?


You could start by checking the fuses, I'm pretty sure that the reverse clutch is applied hydraulically. The forward cluches all use electric solenoids. I could be wrong.

Nov 12, 2009 | 1996 Ford Taurus

1 Answer

Cars gears wont engage after cluch and presure plate change!


Is it cable or hydraulic??? if hydraulic it needs to be bled.and possibly the throw-out bearing assembly isnt installed right.

Oct 02, 2009 | Fiat 124 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...