Question about 2000 Ford F350 Super Duty Super Cab

1 Answer

I am not getting any power to my cruise control. It's not activating at all. Everything else works though. What do I need to do?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 39 Answers

If it is on the pad in the steering wheel and you have checked the fuse, its more then likely the pad. These are known for problems on fords.

Posted on Aug 25, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

While driving hit resume cruise control and the car speed up to 100 and brakes would not work. Had to shut engine off in middle of freeway, what could it be?


Could be a faulty cruise control servo activator. The power to move the cruise control Actuator is most likely coming from the Brake power hydraulic booster vacuum pipe and if the cruise control vacuum servo is failing and leaking in air you lose the brakes power hydraulics.
check the vacuum pipe coming off the power booster brake master cylinder vacuum pipe you may find a tee connector in the vacuum main pipe and follow it to see where it goes to. Could be a break in the cruise control vacuum hose but if it is only happening when the cruise control is activated a fault or leak in the cruise control servo device is the main suspect. Which you should find at the other end of the cruise control vacuum hose.

Jan 31, 2016 | 2004 Oldsmobile Alero

2 Answers

My cruise control stoped working, my speedometer still works


cruise control have there own fuse check that ,make sure it is still hooked up to throttle ,check vacuum lines and power plugs , your speedo has nothing to do with cruise,also check that it is activated,test horn ,YES horn and cruise use same relay ,make sure your brake pedal is retracted ,and that brake lights work as well, good luck with it if I can be of further help get back to me ,hope I helped you.
Woody

Aug 27, 2014 | Cars & Trucks

1 Answer

Why does'nt the Cruise Control Activate 2007 Chrysler Pacifica


Hi Daniel, I'm glad to help! One of the most found problems with cruise control's inoperative here at the dealership is a vacuum problem. If you do not have vacuum from the engine to the cruise control under the hood, then even though the rest of the system is working fine it will not pull the accelerator pedal. NEXT: Another problem could be that the cruise control unit under the hood is not getting power from the brake switch. Check and see if there is power at the unit's connector under the hood. If there is no power then replace the brake switch. NEXT: The PCM may not be getting a signal to apply the cruise and this mainly happens because of a cruise switch problem OR the signal is not getting through the "Clock Spring". This could be either one causing this problem, so replace the switch first because its cheaper. If all of these things check out good then it could be the Cruise Control Unit itself. Hope this helps and have an awesome day Daniel.

Jun 25, 2014 | 2007 Chrysler Pacifica Touring

1 Answer

How to get cruise control working on 94 buick park avenue


Go online to Autozone.com and register your car for free wiring diagrams and fusebox layouts. Then look to see how the Cruise control is fused. It may just need a new fuse.

There are some Cruise units which work with Vacuum. For those you need to apply Vacuum to see if the diaphragm is sealed or leaking.

The rest of the controls are pretty simple. Everything under the hood my be fine and the problem may be in the activation switch. The off and on control may simply not be turning the Cruise on. DO NOT HOT WIRE THE CRUISE UNIT. It needs to shut off with sensing the Brake pedal and the normal power feed needs to cut off.

Now Salvage parts work well for this kind of repair as long as the car was not front end collided in an accident. You can also scarf up extra mounting hardware in case you drop something. The stalk controls on the column are a mixed matter. Some Salvage yards want to sell the entire steering column as a unit, some will sell the stalk controls, steering wheel, etc. piece by piece.

Carparts.com is a collection of networked Salvage yards which ship to your door. They show the parts beforehand, rate condition, and show prices all for you to select. Some have warranties.

You should probably trace the wiring to see if the Cruise unit is getting power. If the power is reaching the box and pod under the hood and then not working, it is probably your problem.

Please rate my info.

Dec 12, 2012 | 1994 Buick Park Avenue

1 Answer

Cruise control inop


if the cruise control does not activate. Check the cruise control fuse. Do a visual check of all wiring relating to the cruise control system. Visually inspect the brake (and clutch if so equipped). If these are out of adjustment, the voltage cannot get to the components down stream with enough power to operate the cruise control.
Visually inspect for vacuum leaks in the release hose and valve, If the cruise control system fails to maintain the set speed, check the throttle linkage adjustment.

Jan 24, 2012 | 2009 Dodge Caliber

1 Answer

Everything works (cruise buttons and dash indicators), but it just won't activate cruise. at all. the fuse is on a relay and it's controlling other things that are working fine.


If you have a transmission or emission trouble code stored on some models it will disable cruise.Also I have seen the cable that goes from cruise box to throttle become detached.Good luck.

Feb 26, 2011 | Ford Escape Cars & Trucks

1 Answer

My cruse control stopped working. Could it be something simple like a blown fuse?


Possibly. Have you had it in to the dealer for service lately? There was a cruise control recall on that model. Dealers were told to disconnect the cruise until replacement parts were available. You could also try lifting the brake pedal with your toe while trying to engage the cruise system, If the brake pedal switch is out of adjustment it will not let the cruise activate. Always check fuses first though.

Aug 17, 2010 | 2000 Ford Windstar

2 Answers

I own a 2005 GMC Canyon Five CYL and the cruise control stopped working last niight. You push the button and no cruise. I checked the fuse and it is ok I exchanged with another 10AMP and no change still...


Start with the simple and check the fuses and the Stop lamp switch. Check your brake lights, if they're not working, the cruise won't work either. If they're not working, check the fuse for them, if the fuse is fine, then take it into the dealer, there's been a recall issued on the brake switch, so it should get fixed for free.
Cruise Control Disengaged
The powertrain control module (PCM) disengages the cruise control operation based on the signals from the following switches:

* The stop lamp switch
* The TCC brake/cruise release switch
* The clutch release switch, if equipped
* The cruise control On/Off switch

The TCC brake/cruise release switch and the stop lamp switch are mounted on the brake pedal bracket. When the brake pedal is applied, the normally closed TCC brake/cruise release switch opens and the normally open stop lamp switch closes. The PCM detects a low signal voltage on the TCC brake/cruise release switch signal circuit and a high signal voltage on the stop lamp switch signal circuit. When the clutch pedal is applied, the normally closed clutch release switch opens and the PCM detects zero voltage on the CCP switch signal circuit. The vehicle speed stored in the memory of the PCM will be erased when the cruise control On/Off button is turned OFF, or the ignition switch is turned OFF.

The Cruise Control System will disengage when the PCM detects that a driver override function has been active for approximately 60 seconds .

When the Cruise Control System is disengaged, the PCM sends a class 2 message to the instrument panel cluster (IPC) in order to deactivate the cruise control indicator.

Cruise Control Inhibited
The powertrain control module (PCM) inhibits the cruise control operation when any of the following conditions exist:

* A cruise control related DTC has been set.
* The vehicle speed is less than 40.2 km/h (25 mph) .
* The vehicle is in PARK, REVERSE, NEUTRAL, or 1st gear.
* The engine RPM is too low.
* The engine RPM is too high, with fuel cut off.
* The vehicle speed is too high, with fuel cut off.
* The system voltage is not between 9 volts and 16 volts .
* The Traction Control System (TCS) is active for more than 2 seconds .

Thank you for using Fixya and start with replacing the stop lamp switch. Even though the brake light work, it;s been known for that switch to cause your issue. that's way there was a recall for it.

Apr 01, 2010 | 2005 GMC Canyon

2 Answers

My 2001 nissan frontier 4x4 cruise control will not activate even though the cruise light will display. it will not lock into cruise. Where do I start checking for possible problems?


look for any loose or corroded wires and failin vacuum hoses in engine area--u need to get it code scanned even if there r no warning lites

Dec 30, 2009 | 2001 Nissan Frontier Crew Cab

2 Answers

How do i turn on the cruise control for a 96 land rover discovery??


Like many cruise control systems there are the working controls and sepearate master power switch that can disable cruise control so it can't be turned on accidentally. The working controls to set speed, acc and off are on the steering wheel. There is a master power switch though on the center area of the dash next to the left of heater controls on a US model. It is a picture of a road running straight under an overpass.

The system is vaccumm controlled though and if you have a vaccumm leak it will not work. They are pretty easy to fix though and easy to see. Open the hood and find the throttle body assembly. Look for the throttle cable and in that area there should be a black soft plastic hose about the thickness of a pen. If this is diconnected from any connectors or cracked the cruise control won't work. Good Luck!

Mar 20, 2009 | 1996 Land Rover Discovery

Not finding what you are looking for?
2000 Ford F350 Super Duty Super Cab Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...