Question about 1992 Acura Integra Hatchback

1 Answer

1992 integra under full throttle just shuts off like you turn the ignition off, ease off the the pedal it runs great again.........any suggestions?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 86 Answers

Sounds like low fuel pressure. It could be a clogged fuel filter or a bad fuel pump.

Posted on Aug 25, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

P0322,P1544,P0121


The fault code P0322 means "Ignition/Distributor Engine Speed Input Circuit No Signal"
The P1544 means "Seat Direction Switch Assembly Circuit Open"
The P0121 means "Throttle/Pedal Position Sensor/Switch A Circuit Range/Performance Problem"
when you know the code, you can most likely repair it yourself.
_______________________
elm327 bluetooth scanner

Sep 06, 2012 | Volkswagen Cabrio Cars & Trucks

Tip

How to reset ECU,Throttle and Accelerator Position Learning


Hi.

Below the procedure to reset ECU,Throttle and to perform Accelerator Position Learning on Nissan. It works on Titan, Altima, Infinity, pathfinder and other models.

ECU Resetting


While performing the procedures below, ensue that you are respecting the times stated. If the steps are not done within the specified times, the module will not reset. You will need to use a watch or a chronograph while performing the procedures.

Procedure:

1. Ensure that the accelerator pedal is fully released, set ignition switch to the “ON” position, then wait 3 seconds.
2. Follow the steps a and b below, repeat the two steps in sequence quickly for five times within 5 seconds.
a. Push hard the accelerator pedal untill fully depressed.
b. Release the accelerator pedal in full.
3. Wait 7 seconds, then depress the accelerator pedal completely, and hold it for about 10 seconds until the CEL (check engine light) starts blinking.
4. Release the accelerator pedal while the CEL is still blinking.
5. Wait 10 second.
6. Depressthe accelerator pedal in full and hold it for 10 seconds or more.
7. Fully release the accelerator pedal while the CEL light keeps flashing.
8. Turn the ignition switch to “OFF” position and start the vehicle. If procedure has been done correctly, then the light light will turn off.
If the light continues to stay on, repeat the procedure.

Accelerator Pedal Release Position Learning

Procedure

1. Ensure that the accelerator pedal is completely released before starting the procedure.
2. Turn the ignition switch “ON” and wait at least 2 seconds.
3. Turn the ignition switch “OFF”, and wait at least 10 seconds.
4. Turn the ignition switch “ON” and wait 2 seconds.
5. Turn the ignition switch “OFF” and wait 10 seconds.

Throttle Valve Closed Position Learning

Procedure

1. Ensure that accelerator pedal is completely released.
2. Turn ignition switch to the “ON” position.
3. Turn ignition switch to the “OFF” position and wait at least 10 seconds.
Ensure that the throttle valve moves after turning the switch off.

Idle Air Volume Learning (Throttle Position Learning)

Procedure

1. Follow the Accelerator Pedal Released Position Learning described above.
2. Do the Throttle Valve Closed Position Learning also described above.
3. Start the engine, and allow warming up.
4. Turn the ignition on “OFF” positionand wait 10 seconds.
5. Ensure that accelerator pedal is fully released, then turn the ignition switch to “ON” position, and wait 3 seconds.
6. Repeat the steps a and b below five times within 5 seconds in sequence.
a. Push hard the accelerator pedal untill fully depressed.
b. Release the accelerator pedal until reaching full extension.
8. Wait 7 seconds or more, depress the accelerator pedal completely and hold the pedal down for about 20 seconds until you see that the Check Engine Light stops blinking and starts getting steady..
9. Rrelease completely the accelerator pedal within 3 seconds after the light coming ON.
10. Start engine and let it run at idle for about 20 seconds.
12. Test the engine to ensure the idle speed and ignition timing are set correctly.

Regards.

on Mar 25, 2010 | Nissan Titan Cars & Trucks

1 Answer

I have a 1992 Chevy 1/2 ton 5.7 Litre 1500 series truck. The truck while idling suddenly stalled. I verified the fuel pump by taking the pump side off to the filter and verified fuel to the filter by...


Doesn't sound like you've considered spark. Sounds like you're losing spark somehow. You seem to know your way around a truck, so I don't have to explain every little thing. Just check all the ignition stuff, go through the distributor and coil and plugs and wires. If it's gettin fuel, its either a spark issue or air/vaccum issue. Hope this helps.

Jun 12, 2011 | 1992 Chevrolet K1500

1 Answer

91 ACURA INTEGRA GS SHUTS OFF WHEN I START IT UP


suggest the first thing you do, is to pull the codes off the ECM, and go from there...more than likely it's a TPI, idle sensor or fuel pump relay thats dirty or sticking thats causeing the problem...
Your local AutoZone can perform the scan and explain the results to you...free of charge.
Good luck, hope this helps,please rate me a fixya.

Jul 20, 2009 | 1991 Acura Integra Hatchback

1 Answer

Oil light comes on after oil change 1992 acura integra.


If the oil lamp itself is illuminating it is not a maintenance light that can be reset the oil pressure sending unit is detecring low oil pressure. You should have the vehicle serviced right away. The reset procedure for the maintenance indicator is as follows,with the key off depress & hold the odometer/trip button on the instrument panel turn key to run position wait 10 seconds for reset

Apr 17, 2009 | 1992 Acura Integra Hatchback

1 Answer

No overdrive, no cruise


probally a crack inthe cruise controll hose

Jan 07, 2009 | 1992 Buick Park Avenue

1 Answer

Engine sputtering


under the dash on the driver side the mane full relay may need replacing or its the full pump

Jan 07, 2009 | 1990 Acura Integra Hatchback

1 Answer

Acura integra 1992 LS ignition fuse location


No pro bro but look under the hood on passager side just above the battery fuse box right thier and under the stering wheel thier's another one brake lights and power windows and all.

PEACE AND LOVE BRO

Oct 12, 2008 | 1992 Acura Integra Hatchback

1 Answer

Transmission Problem???????


check the linkage for the selector and see if anything is binding.

Jul 18, 2008 | 1992 Acura Integra Hatchback

Not finding what you are looking for?
1992 Acura Integra Hatchback Logo

Related Topics:

123 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...