Question about 2004 Chevrolet Blazer

1 Answer

Which wire on the back up lights near the bulb is the ground wire the black one or the green one.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,926 Answers

Black is always ground.

Posted on Aug 25, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear harness was bad they replaced with trailer harness and trying to fig out what yellow brown light green an dark green are on frame of truck it hooked in to so i can fix i un hooked not knowing what had...


Your description, I take it, is a problem with the wiring harness going from the driver's compartment to the rear lights. If that is the case, the normal color code for GM is brown for tail lights, dark green for the right stop & turn, yellow for the left stop & turn and light green for the backup lights. Any black wires should be grounded. The white wire in the trailer harness is for a ground when used on a trailer. It sounds like you have the green and yellow T&S wires shorted together somewhere! Some of the later vehicles use separate stop and turn bulbs... these would have a separate wire for the stop lights only, but I don't think your truck is new enough for that. Good luck!

Nov 25, 2013 | 1993 GMC Sierra

1 Answer

1996 Ford Contour blow fuse when in reverse


You most likely have corrosion or a short in the socket(s) of your white back up lights. Remove the bulb(s) and inspect the socket base. Clean out any corrosion. The back up light switch is on the shift linkage. The Switch could have shorted internally or the wiring from the switch to the back up lights can be grounded somewhere on the chassis / body / frame. You will need to perform resistance checks to ground with the back up light bulb(s) removed. If you have shorts to ground with bulbs removed you have a wiring problem. Keep in mind that if you have 2 wires to the light... one wire is power and the 2nd wire is ground (usually green). A back up light bulb that is loose in the bulb base and has twisted the 2 wires together from vibration will also cause the fuse to fail.

Thanks for choosing FixYa,
Kelly

Sep 21, 2011 | Ford Contour Cars & Trucks

2 Answers

Of the 3 wires that feed into the headlight bulbs on my 2000 F350, I need to know which is positive and which is ground


The BLACK wires are ground. The LIGHT GREEN/BLACK wires are your high beam circuits. Then the low beam circuits are DARK GREEN/ORANGE on the right side and DARK BLUE/WHITE on the left side.

Jun 19, 2011 | 2001 Ford F350 Super Duty SuperCab

2 Answers

1998 ford e150 one headlight dont work already tried new light


If you replaced the bulb and are sure the new one is good, you have a wiring concern. First you need to be sure the terminals at the headlamp connector are making a tight connection. If this is good, check for a good ground at the black wire by using a test light with the clip connected to the positive battery terminal. Touch the test light to the black wire and it should light. If ground is good check for voltage, again using the test light but with the clip on the negative terminal. Test at the red/black wire for low beams or the light green/black wire for high beam. Low beams use 10 amp fuses #'s 25 and 31. High beam uses fuse # 30 and is 15 amp. If voltage or ground is not present and the fuse is good you need to trace the circuit and repair the wire.

Apr 06, 2011 | 1998 Ford Econoline

1 Answer

1984 toyota camry no brake lights switch fuse and bulbs are good


check wiring further back in boot rh side there is little black box that plays up fitted there.check this cant get anymore must by pass box now.

May 31, 2009 | 1984 Toyota Camry

2 Answers

2003 ford ranger 7 pin wiring for a trailer all I need is what the colors on the wiring are blue/yellow/green/black/brown/white


White is ground, black is power to trailer battery trickle charge, blue is brakes, green is tail/running lights, red is left turn signal and left brake light, brown is right turn signal and right brake light, yellow is aux power/back up lights. This is the general color coding, there are exceptions, white, black, and blue are pretty much always as listed above, sometimes the others vary. If you find you are having trouble, post any further questions here, I'll be glad to help out. Curt

Apr 24, 2009 | 2003 Ford Ranger Regular Cab

4 Answers

Head lights go out when I switch to high beam


You probably have a short in your wireing somewhere so when u go to turn your brights on its too much power so then they turn off

Apr 19, 2009 | 2002 Ford Taurus

2 Answers

2001 ford taurus ABS will not light but brake light on


You have a bad ABS module. Had the same problem with my 2000 Taurus. The ABS module is a Bosch 5.3 You can have yours rebuilt for $170 or go to a junk yard and pull one from a 2000-2003 Taurus. Make sure its a traction control module if you have it on your car!

Apr 14, 2009 | 2001 Ford Taurus

1 Answer

2005 Scion TC brake light wire color code question


1. is white with black strip- ground

2. is green is left brake and

3. is green with white is running light

Mar 28, 2009 | Scion TC Cars & Trucks

1 Answer

1998 Cadillac DeVille


ok the easiest way to check is to take a voltage probe and check each wire this way it will tell you which wire is recieving current. the positive side should be marked either red,yellow or green with black stripe and sometimes orange. on the ground side it should be marked black,white, turn signals should be green for right side and yellow with black stripe for left. running and parking lights should be brown. back up lights are marked blue.

Aug 28, 2008 | 1998 Cadillac DeVille

Not finding what you are looking for?
2004 Chevrolet Blazer Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...