Question about 2007 Hyundai Accent GS Hatchback

1 Answer

Engine light came on . How do I get the code? Did by accident counted 22 on off but there may have been some before I noticed

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

You need an OBDII code reader in order to read the code from the engine. If you have one, you just plug it in to the jack located on the lower left side of the dash, near the steering wheel, and start the car. Also, Midas has been offering free code readings, and it takes about 5 minutes.

Posted on Aug 28, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I drive a 1991 galant with 4g63 engine and the check engine light is on after 5 minutes of starting the car, i already reset the computer bu taking off the negative pole of the battery. the car has no o2...


Your OBD 1 that means put two wire together and it will flash the code by counting the flashes of the ck engine light if your production date is 9/91 you have a recall on the 02 sensor it doesnt matter how long you owned it or if your not the original owner here is the recall number EMR 92 003 but here the deal its only for car in the states like california any other place your out of luck to access the code you will need a voltmeter there it will flash or a analog voltmeter there you will measure the sweep of the needle movement to get the code go under the dash and find the 12 pin connector on the driver side kick panel top right corner is pin 1 and lower left is ground or pin 12 or chasis ground watch the meter movement and count the flashes first flash is long second is short example for code 12 its one long flash is for number 1 two short flash is 2 for code 22 its two long flashes thats 2 and 2 short flash is 2 put it together its 22 there can be a combination of code there your care doesnt really have that much management just EGR, TPS, just the simple needs

Aug 21, 2011 | 1991 Mitsubishi Galant

1 Answer

Loss of power light came on the other day and now wont fire it will turn over though


Have you tried cycling key, to on, off, on, off, on, and leave on and count the flashes of the check engine light?
(Just to on, not start) This should retrieve any trouble codes. Write them down & get back to us. It will be 2 digits and will work like this example: 2 flashes, pause, then 2 more flashes= code 22. 3 flashes,pause then 5 more flashes would be code 35. Code 55 means end of message.

Oct 16, 2009 | 1987 Plymouth Reliant

1 Answer

Check engine codes for 1991 Dodge Spirit LE , light comes on but does not blink then goes out.


Turn key to on, then off, then on, then off, then on & leave it on, (not start, just to on) then count the number of flashes of check engine light. It will flash,then have a small pause, then flash again. It will be a 2 digit number, for example: 2 flashes, pause, 2 more flashes, will be code 22. 3 flashes, pause, then 5 more flashes would be code 35. When you get 5 flashes,pause, then 5 more, That is code 55 which just means end of message. Get back to us with codes & we'll advise of what to look for.

Sep 21, 2009 | 1991 Dodge Spirit

1 Answer

2001 HONDA ACCORD CODE P0740 TRANSMISSION


Horsecrap...go to an independent transmission dealer after you call the extended warranty folks and complain!
I can count the number of Honda transmissions that go bad before 300,000 miles on one hand.
Good Luck

Jun 22, 2009 | Honda Odyssey Cars & Trucks

1 Answer

When I start my car, it is running rough, must keep on full throttle or it quit running.will not idle at all.


Do you know how to retrieve fault codes by cycling key, on, off, on,off, on, and leave in on position & count flashes from check engine light. 2 flashes , pause, 2 more flashes, is code 22. 3 flashes, pause 3 more, is code 33 etc.... Get back to us with those codes if any. By the way code 55 means end of message.

Jun 04, 2009 | 1992 Plymouth Acclaim

1 Answer

My car will not stay running, it is very rough, then quits


Do you know how to retrieve fault codes by cycling key, on, off, on,off, on, and leave in on position & count flashes from check engine light. 2 flashes , pause, 2 more flashes, is code 22. 3 flashes, pause 3 more, is code 33 etc.... Get back to us with those codes if any. By the way code 55 means end of message.

Jun 04, 2009 | 1999 Plymouth Voyager

1 Answer

I changed plugs and wires got a oil change.. but my car still shuts off sumtimes what should i do


Try cycling key, on, off, on, off, on, and leave on (not start) & count flashes of check engine light. 3 flashes, pause, then 3 more is code 33. 2 flashes, pause then 2 more, is code 22 etc. See what you get for codes first before guessing on replacing parts. 5 flashes, pause, then 5 more, is code 55 which means end of message (codes.)

May 30, 2009 | 1996 Plymouth Breeze

1 Answer

Loss of power


Have you cycled key to see if there are any trouble codes stored?
On,off,on,off,on. Leave in on position (not start) and count any flashes from check engine light. 2 flashes,short pause, and 2 more flashes =22. 3 flashes, pause, 3 more is code 33. etc when you get code 55, that's end of message.Let us know if anything comes up.

Apr 04, 2009 | 1995 Dodge Intrepid

1 Answer

Check engine light on


Cycle your key, on (not start) off, on, off, on. Leave it on 3rd time, and count check engine flashes. It will be a 2 digit number each time. For example: flash,flash, pause, flash, flash. Is code 22.
Flash,flash,flash,pause,flash,flash,flash, is code 33. There will be a little longer pause after each set of 2 digits. When you get flash,5 times, then flash 5 times again, that's code 55 which means end of trouble code message. have a piece of paper ready, write them down, and get back to us with results.

Feb 20, 2009 | 1989 Plymouth Reliant

1 Answer

Engine code retrieval for a 1999 dodge avenger


3 times ..turn the key > off on off on off on .> then count the flashes of the light , flash flash pause flash flash , = 22 , pause , i think when you see 5 flashes pause 5 flashes , that means end of list . there might be multiple codes , have a note pad , you have to do it twice to be sure of the code(s) .

Jan 22, 2009 | 1999 Dodge Avenger

Not finding what you are looking for?
2007 Hyundai Accent GS Hatchback Logo

Related Topics:

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...