Question about 1990 Toyota Corolla

1 Answer

I am replacing passenger side cv axle and can not get the inner portion seperated from the trans axle. Am I doing something wrong I was wondering if both half axles need to be dropped to remove passenger side half axle from transaxle by tranny.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 125 Answers

No just pry it out with a pickle pork

Posted on Aug 25, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace my inner axle on the passenger side of my 2002 Dodge Ram 4x4 4.7L. I lent my truck out and the C clip let go of the CV axle. The intermediate axle spline is stripped and I need to change...


Lift and support front end on suitable jack stands preferably on frame. Remove right front cv axle, stub shaft, and seal. You will need to pull the right front brake caliper assembly loose and place to the side. Then remove bolts from shock and upper control arm and hub nut to do this. Next, remove axle lock actuator on passenger side of front axle. Place a drain pan underneath front diff cover and remove cover and drain axle. In the center of differential there will be an 8 mm head bolt holding spider gear cross-shaft. Remove bolt and cross-shaft only! Push inner axle in until clip clears inside of passenger spider gear. Set clip aside and push/pull axle shaft straight out to passenger side.

Feb 09, 2015 | Dodge Cars & Trucks

1 Answer

1991 ford tempo passenger axle how do I remove it


You will need to remove the passenger wheel and large nut holding the axle to the center of the hub of the spindle. Then remove the nut and un-seat the lower ball joint. Separate the lower control arm from the spindle and pull spindle out while pushing axle in, separate the spindle from the axle and tie aside out of the way. The axle is held into the trans-axle with a circlip, you will need to get a pry bar behind the inner CV joint and pop the inner spline joint out of the trans-axle.

Jul 09, 2014 | Cars & Trucks

1 Answer

I recently replaced my passenger side CV axle as well as the CV axle seal due to a leak. After everything was installed I found I still have a leak and it has actually become slightly worse. The car is on...


It sounds like the inner seal needs to be replaced which means a tear down of the transmission it might be just as easy to replace the tranny but a good repair shop should be able to do this far cheaper.

Oct 28, 2013 | 2005 Pontiac G6 GT

2 Answers

01' Mitsubishi Eclipse cv axle removal passenger side


The passenger side has a inner and outer shaft and you would remove the axle nut and shaft from spindle then the center bracket and bearing (two bolts against engine block), sliding out the axle assembling at that point, or jerking it out, careful not to pull on the cv axle end but rather the jack, or inner, shaft. After removal, separate the middle by hanging upside down and taking a hammer to it, striking the inner shaft while turning around. Dont hit the dust shield or seals. Install in reverse order. Quick tip: you may get around removing ball joint by only removing both strut bolts, and possibly tie rod end bolt.

Mar 02, 2013 | 2001 Mitsubishi Eclipse Spyder

1 Answer

Wobble on inner CV tripot on a 2006 impala


if you can " waggle " a CV joint

bearing part or bearing housing of the drive shaft joint worn
..replace the cv






index-ga5va5500wygjikc4v5xzqjs-2-1.jpg

Apr 26, 2017 | 2006 Chevrolet Impala

2 Answers

Need help removing right side cv axle on 94 toyota


Assuming you have the spindle off - you need a pry bar between the inner mount and the transaxle. Give it a bit of a snap as it is held in with a lock ring around the spline. Note the gap - when replacing it - pop it in fairly well till you feel the snap ring lock back into position. If you are replacing it - inspect the new one - the lock ring should already be installed.

Dec 12, 2009 | 1994 Toyota Camry

1 Answer

I have a 1999 isuzu 4wd rodeo 6 cylinder and was wondering if Need to install a new boot kit or if I need to replace the entire front left cv axle shaft. I had a tear in my rubber boot and noted some...


Do not try to get the cv axle out ot the axle housing. It is a major operation. Remove boot and disconnect the inner cv joint and save about five hours of time. The choice is yours ,boot or reman cv axle. You will need to take the reman. axle apart to install it though and some new clamps. Not a simple operation.

Sep 28, 2009 | 1997 Isuzu Rodeo

1 Answer

Need instructions to replace front passengers side cv joint


Do yourself a favor and replace the whole cv shaft. Quicker, eaiser and not much money. First get the car in the air and remove the wheel. Then pop the lower ball joint. This is done by unbolting it from the knuckle and using a ball joint seperator fork and a hammer. Then remove the spindle nut on the end of the cv shaft. You push down on the lower A arm pulling the ball joint out of the knuckle and push the cv shaft out of the hub. Once these are dislogged, you can movel the strut and hub out of the way and pull the cv shalt out of the trans axle. Push the new one in and reverse what you did.

Aug 08, 2009 | 1996 Chevrolet Cavalier

1 Answer

Need to know a parts name


If you are referring to the metal part the axle slides into,It's cold the transmission,If it is leaking around the shaft it is called the inner cv axle seal,But if something blew up,I'd let a mechanic physically look at it.

May 16, 2009 | 1995 Pontiac Grand Prix

1 Answer

Trans axles


remove whole axle.. take strut assembly and steering gear apart ,. then big nut at hub, pull strut/steering linkage away from axle out of center...then pop inner axle shaft out of transmission , with drip pan underneath as you will flow trans fluid from there..do both sides then separate trans and drop...good luck

Dec 16, 2008 | 1997 Nissan.5 Altima

Not finding what you are looking for?
1990 Toyota Corolla Logo

Related Topics:

192 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...