Question about Honda CR-V

Open Question

How to remove the knock sensor on cr-v 2002 - CR-V Honda Cars & Trucks

Posted by on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 99 Answers

SOURCE: knock sensor question

knock sensor is on the passenger side of engine block, some knock sensors fit into water jacket others did not

Posted on Nov 30, 2008

buffalonyman
  • 1865 Answers

SOURCE: Have a 2002 Cadillac Escalade AWD 6.0 Knock sensor intake manifol

If you're apprehensive about doing this work, buy a Haynes repair manual (about $20), It shows you how to remove the manifold

Posted on Nov 05, 2009

Testimonial: "That the best advice I?ve gotten, thanks!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Engine started knocking on a honda cr-v 2.0 vtec


check your oil level, color, and smell. My guess is that the low oil pressure light is on because of literal lack of oil to pressurize. Generally when you get that light and a knock it points to major engine repair or replacing the engine. Knocks due to oil pressure can indicate many things from a bad head gasket to a stretched rod or blown piston rings. Check your coolant reservoir for signs of oil entering the cooling system as it will float on top of the coolant. By the sound of it it needs major mechanical repairs

Apr 05, 2014 | Honda Cars & Trucks

1 Answer

Were is the knock sensor on 2002 protege5 2.0L


The knock sensor is located under the intake manifold to replace do the following
Disconnect the negative battery cable.
Remove the intake manifold.
Disconnect the sensor connector.
Remove the sensor from the engine block.
Installation is the reverse of the removal procedure

Sep 28, 2012 | 2002 Mazda Protege

1 Answer

Where is the knock sensor located on a 2003 honda crv engine


Just done this on a 2002 (mk2) CR-V with 2 litre ivtec petrol engine. The knock sensor is screwed into the engine block underneath the inlet manifold. The best access to it is by removing the inlet manifold but this takes time. I replaced it from below by:

1) remove the undertray that is fastened to the front bumper, to do this its two bolts and lots of plastic rivets - lever the centre pins out of the rivets and they will come out.
2) from underneath the car you can now see the knock sensor in the centre of the engine block, it has a 27mm AF hex and a cable going to it.
3) disconnect the cable from the knock sensor, it has a latch on the plug that needs to be pressed, if like me you can't reach to press the latch don't worry move on to the next step.
4) Get a large 27mm open end spanner and undo the knock sensor, if you wern't able to disconnect the cable in the previous step it is possible to take the sensor all the way out of the block with the cable still attached. It is then much easier to unlatch the cable.
5) to refit the new one you need small hands or better access - there is a plastic clip holding a cable to the engine on the left hand side of the engine I found that by removing this clip (a single 10mm bolt) I could move the bundle of cables and get better access to refit and connect the new knock sensor.
6) Fit the new knock sensor into the block, tighten it to the recommended torque (can't get a torque wrench in so just nip it up, do not overtighten).
7)reconnect the cable.
8) refasten the cable clip holding the bundle of cables you removed to get access.
9) refit undertray.
10) I don't have a code reset device and the check engine light was still on after this work but it went out after three complete engine cold,hot,cold cycles. and has stayed out since.

Mar 24, 2012 | 2003 Honda CR-V

1 Answer

Knock sensor for a 2002 2.0 kia sportage


1. Remove the intake manifold support bracket
2. Disconnect wire harness
3. Loosen bolt remove harness

Mar 17, 2012 | 2002 Kia Sportage

1 Answer

Where is starter on 2002 honda crv?


Honda_Cr-V_2001-2006
Starter - Removal & Installation

2.0L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:

    Negative battery cable Starter wiring harness connectors Starter motor

To install:
  1. Install or connect the following:

    Starter motor. Tighten the bolts to 33 ft. lbs. (44 Nm). Starter wiring harness connectors. Tighten the battery cable nut to 79 inch lbs. (9 Nm). Negative battery cable

2.4L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:

    Negative battery cable Knock sensor connector Starter wiring harness connectors Starter motor

    8b26da5.jpg
    Fig. Starter mounting

To install:
Install or connect the following:

Starter motor. Tighten the upper bolt to 33 ft. lbs. (44 Nm); the lower bolt to 47 ft. lbs. (64 Nm). Starter wiring harness connectors. Tighten the battery cable nut to 84 inch lbs. (9 Nm). Knock sensor connector Negative battery cable


Hope this help (remember comment and rated this).

Apr 04, 2010 | 2002 Honda CR-V

1 Answer

Location of the knock sensor on a 2002 kia sportage


remove the intake manifold ,remove radiator ,remove radiator intake and outake housing, remove fan ,remove all belts: power steering, alternator and if you have a/c, remove harmonic balancer ,remove timing belt covers, remove timing belt remove intake housinng once you have remove all the above, your freaken engine will look naked, you can see the location of the knock sensor is locate in the engine valley u might wanna google knock sensor so u knoe what it looks like

Feb 19, 2010 | 2002 Kia Spectra

1 Answer

How do I replace the Knock Sensors on a 2002 GMC Sierra 2500HD 6.0L V8 Gas engine? How do I change the serpentine and AC belts? Last but not least how to replace the drivers front differential seal?


remove the intake manifold ,remove radiator ,remove radiator intake and outake housing, remove fan ,remove all belts: power steering, alternator and if you have a/c, remove harmonic balancer ,remove timing belt covers, remove timing belt remove intake housinng once you have remove all the above, your freaken engine will look naked, you can see the location of the knock sensor is locate in the engine valley hope this helps u might wnat to google knock sensor so u knoe what it looks like

Feb 19, 2010 | 2002 GMC Sierra 2500HD

1 Answer

Have a 2002 Cadillac Escalade AWD 6.0 Knock sensor intake manifol


If you're apprehensive about doing this work, buy a Haynes repair manual (about $20), It shows you how to remove the manifold

Nov 05, 2009 | 2002 Cadillac Escalade

1 Answer

How to replace knock senor switch on 2002 mazda protege 5



Removal & Installation

  1. Disconnect the negative battery cable.
  2. Remove the intake manifold.
  3. Disconnect the sensor connector.
  4. Remove the sensor from the engine block.
  5. Installation is the reverse of the removal procedure.

    0900c1528019fa95.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Knock sensor removal and installation-Mazda 3

  1. Disconnect the negative battery cable.
  2. Remove the intake manifold bracket.
  3. Disconnect the sensor connector.
  4. Remove the sensor from the engine block using special tool 49H018001 or equivalent.
  5. Installation is the reverse of the removal procedure.

    0900c1528019fa96.jpg enlarge_icon.gifenlarge_tooltip.gif GL G

May 09, 2009 | 2002 Mazda Protege

1 Answer

Knock sensor question


knock sensor is on the passenger side of engine block, some knock sensors fit into water jacket others did not

Nov 24, 2008 | 1999 Chevrolet C1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

167 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7711 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...