Question about 2008 Chrysler Aspen

Open Question

How to change wheel bearing hub assembly on 2008 chrysler aspen

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 23 Answers

SOURCE: how do u remove front wheel bearing

Take off the wheel, then the brake caliper, noow you have the roter. in the center is a cap, the center cap, this comes off by pruing it off with a screwdriver. Inside that a retaning pin, take that out, then a nut cover, and nut with grooves in it from where you took out the pin. It is good to mark about where it was so when you put it together, you will not overtighten it.

Take that nut off, then you should be able to take off the whole assembly, bearings and all. If this is a sealed unit, you have to but a roter that will have the guts already inside it. make sure you clean off all of the old grease, you are going to replace critical parts, so you need new grease for them. Also make sure your spildle is not grooved, if so haw bad, you might replace it to if all gualled up.

on a sealed unit you just reverse the steps from taking it off.

if not you have to knock out the old races in the caliper, the one side by a wide screwdriver and hammer, there are pullers, but from the way it sounds, it is in there tight. Just be carefull not to kill the sides and rotate it around when doing this. once it is out, do the other side, find a socket that size, one thak will fit in the race almost to the edges and beat it out. now make sure the caliper is in a flat surface, and use a blanket or something toi avoid knicking the thing.

once both are out, just reverse the process, grease the inside just a bit and when you put the race in use a socket that is the size of the race, and beat it in evenly.grease your bearings, make sure you do one side at a time, and putting them back on the spindle is a cake walk compared to what you just have done.

hope this helps

Posted on May 26, 2009

Ad
  • 4 Answers

SOURCE: how do i remove a rear wheel hub assembly on a

if you already removed the bolts that attach it to the spindle then you need a bigger hammer

Posted on Sep 17, 2009

roniecon
  • 6826 Answers

SOURCE: 2006 chrysler pacifica-wheel hubs burning hot

The problem might have already been there,the steel wheels are making it noticeable,because they don`t cool down as quick.Most likely is the calipers sticking,or you have a set of high dollar brake pads on the vehicle,and they are heating the rotors up.The high dollar pads are a very hard composite pad witch produce a lot of friction,and heat as a sort of side affect.

Posted on Oct 23, 2009

  • 67 Answers

SOURCE: how to replace a rear wheel bearing on voyager

this is a one piece part hub and bearing assy. even if auto parts sales you bearing separated highly recommend to replace whole unit

Posted on Nov 19, 2009

  • 17 Answers

SOURCE: procedure for front wheel bearing (hub assembly)

jack up vehicle wheel in question and install jack stand.remove wheel. Unbolt 2 caliper bracket bolts and pry caliper assembly up off brake rotor and hang off to the side with bungee.remove rotor . remove large axle nut. From the back of the hub remove hub bolts most commonly 15mm.Using a slide hammer style wheel puller the hub can be removed. if all you have is a big hammer hit the hub back and forth side to side until it can be removed. Bolt in new hub assembly and torque bolts.Install axle nut and torque. install rotor and caliper. reinstall wheel and torque.

Posted on Nov 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the air idle control on the 2008 Chrysler aspen?


They did away with them when they started using the drive by wire system. Electronic throttle.

Apr 13, 2016 | 2008 Chrysler Aspen

3 Answers

Where is the abs speed sensor located on a 2005 pacifica?


Behind each of the front wheel hub

Have to follow the wires to find the rear sensors

The internet should have a picture,easier to just look under the car

Jun 10, 2014 | 2004 Chrysler Pacifica

1 Answer

How do I replace front wheel bearing in a 2008 hyundai accent?


Hi there, I think from memory the whole hub assembly comes with new bearings when you replace it, it's a easy change, remove wheel, remove the brake calliper, remove the front axel nut and the hub should come off, hope this helps, it's a easy change

May 19, 2014 | 2006 Hyundai Accent

2 Answers

How to replace rear wheel studs on a 2008 Chrysler Aspen?


  • Sounds like the axles have to be pulled to get the studs out. Not that familiar with Aspens but if it wont clear the backing plate the hub assembly has to move out away from it.

May 16, 2014 | 2008 Chrysler Aspen

1 Answer

Removing rear wheel studs


there should be one spot while turning rear wheel bearing that will allow one stud to be knocked out and new stud replaced BEFORE trying to remove the next stud... one at a time

May 16, 2014 | 2008 Chrysler Aspen

1 Answer

2008 Dodge Avenger wheel hub replacement


The front bearing comes as a hub assembly, so you should be able to unbolt it from the spindle. You still have to take the axle shaft out.

Jun 03, 2013 | 2008 Dodge Avenger

1 Answer

I have a chrysler lhs 1994 with a bad front wheel bearing and i need instruction on repair


These are the steps you need to follow for this procedure if you have the proper tools.
  1. Remove front caliper assembly and rotor from the steering knuckle as outlined under "Caliper, Replace" in the "Disc Brake" unit repair section.
  2. Remove hub and bearing to stub axle retaining nut.
  3. Disconnect hub bolts then remove hub and bearing assembly from steering knuckle by sliding it straight off end of stub axle. If metal seal on hub and bearing assembly is seized to steering knuckle and becomes dislodged on hub and bearing assembly during removal, or when removing hub and bearing, the finger disc on hub becomes damaged, hub and bearing assembly must be replaced.
  4. If hub and bearing will not slide out of knuckle, insert a prybar between hub and steering knuckle and gently pry hub and bearing from knuckle.
  5. Tighten stub shaft nut, lower vehicle and with brakes applied, torque stub shaft nut to 70 - 90 ft. lbs.

Aug 27, 2010 | 1994 Chrysler LHS

1 Answer

Is the wheel bearing on a 1996 Intrepid pressed in or pushed in?


YOU HAVE TO REPLACE THE WHOLE BEARING HUB AS A ASSEMBLY.

Jun 07, 2010 | 1996 Dodge Intrepid

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

436 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...