Question about 1989 Ford Mustang

Open Question

Procedure for replacing transmission front seal and bushing on 89 mustang lx 4 cylinder w/ od

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 3600 Answers

SOURCE: 1990 ford mustang lx 4cyl, auto blew out it's

a Plugged vent on the tranny could cause this and an overfill of transmisson fluid could cause this, but without inspecting it would not know the cause or if it would strand you again?

Posted on Jul 06, 2009

Ad
RonPark
  • 855 Answers

SOURCE: how do i change the front seal on the automatic

Your first step is to diconnect the battery. Then comes the hard part you must pull the transmission out of the car and put it on a bench or work table (for ease of working). After this you must remove the torque convertor and there is a seal ther and also a seal for the front pump. Ifyou replace both make sure everything is perfectly clean before installing any seals or they will leak again. Transmission fluid is very thin and will find gaps at seals due to dirt very easily. After seals are installed reinstall trans and fill with the proper fluid as per owners manual. Start car and leave it warm up while checking for leaks and recheck the fluid. If everything looks good road test and recheck. If still fine just keep an eye on it and drive away.

Posted on Sep 12, 2009

  • 14036 Answers

SOURCE: need wiring diagram for 2003

CODE P1795 IS 4WD LOW GEAR POSITION SWITCH - CIRCUIT MALFUNCTION.POSSIBLE CAUSE IS WIRING , FAULTY LOW GEAR POSITION SWITCH . FAULT IN TCM

Posted on Sep 06, 2010

  • 1 Answer

SOURCE: no power to fuel pump

fuel pump shutoff switch in the trunk on the left side i believe, try resetting that and all fuses and relays.

Posted on Sep 08, 2010

  • 2309 Answers

SOURCE: 89 mustang lx ( My

you have another circuit piggybackin on the dash lights, my guess is a bad ground to the parking or tail lights, try unplugging the tail lights and front marker lights. if the fuse satys good you have it

Posted on Oct 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ford mustang was making a whine/ rattling noise while doing 20-60 mph then after driving 20 minutes she died at a stop sign, would start up fine in park, but died when we tried to shift,what is wrong


Automatic or stick ?
If its an automatic, it could be something in the torque converter or transmission. The torque converter clutch could be stuck.

Dec 20, 2012 | 1989 Ford Mustang

1 Answer

Bad rod in 1990 mustang lx 4 cylinder


You might as well replace the engine, it is about the same cost. So you are looking at about $2000.00

Oct 01, 2012 | 1990 Ford Mustang

2 Answers

Can i remove the oil pan on my 07 ford f-150 with out removing the engine?


Check this procedure on F-Series...

5.4L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove the transmission.
  3. Drain the engine oil.
  4. Disconnect the engine oil temperature (EOT) sensor electrical connector.
  5. Remove the nut and the starter wiring harness support bracket.
  6. Remove the nut and position the transmission oil cooler lines and bracket aside.
  7. Remove the 16 bolts and lower the oil pan onto the crossmember.
  8. Remove the 3 bolts and position the oil pump screen and pickup tube into the oil pan.
    NOTE Be careful when removing the oil pan gasket. It is reusable.
  9. Remove the oil pan and the oil pump screen and pickup tube.
  10. Inspect the oil pan gasket for damage. If damaged, discard the oil pan gasket and the oil pan-to-oil pump gaskets. Discard the oil pump screen and pickup tube O-ring seal.
To install:
WARNING Do not use metal scrapers, wire brushes, power abrasive discs or other abrasive means to clean the sealing surfaces. These tools cause scratches and gouges, which make leak paths. Use a plastic scraping tool to remove all traces of old sealant.
  1. Inspect the oil pan. Clean the mating surface for the oil pan with silicone gasket remover and metal surface prep. Follow the directions on the packaging.
  2. Position the oil pump screen and pickup tube in the oil pan and position the oil pan into the vehicle.
    WARNING Make sure to install a new O-ring seal. A missing or damaged O-ring seal can cause foam in the lubrication system, low oil pressure and severe engine damage.
    NOTE Clean and inspect the mating surfaces and install a new O-ring seal. Lubricate the O-ring seal with clean engine oil prior to installation.
  3. Position the oil pump screen and pickup tube and install the bolts.
  4. Tighten the oil pump screen and pickup tube-to-oil pump bolts to 10 Nm (89 inch lbs.).
  5. Tighten the oil pump screen and pickup tube-to-spacer bolt to 25 Nm (18 ft. lbs.).
    NOTE If not secured within 4 minutes, the sealant must be removed and the sealing area cleaned. To clean the sealing area, use silicone gasket remover and metal surface prep. Follow the directions on the packaging. Failure to follow this procedure can cause future oil leakage.
  6. Apply silicone gasket and sealant at the crankshaft rear seal retainer plate-to-cylinder block sealing surface.
    NOTE If not secured within 4 minutes, the sealant must be removed and the sealing area cleaned. To clean the sealing area, use silicone gasket remover and metal surface prep. Follow the directions on the packaging. Failure to follow this procedure can cause future oil leakage.
  7. Apply silicone gasket and sealant at the engine front cover-to-cylinder block sealing surface.
  8. Install the oil pan gasket and the oil pan and loosely install the 16 bolts.
  9. Tighten the bolts in 3 stages, in the sequence shown.
    Stage 1: Tighten to 2 Nm (18 inch lbs.). Stage 2: Tighten to 20 Nm (15 ft. lbs.). Stage 3: Tighten an additional 60 degrees.
  10. Install the wire harness bracket and the bolt. Tighten to 10 Nm (89 inch lbs.).
  11. Position the starter wiring harness support bracket and install the nut. Tighten to 10 Nm (89 inch lbs.).
  12. Connect the engine oil temperature (EOT) sensor electrical connector.
  13. Install the transmission.
  14. Fill the crankcase with clean engine oil.

2_14_2012_4_41_50_pm.jpg

Fig. Remove the bolts and the crossmember-F-150 and Mark LT 5.4L Engine

2_14_2012_4_42_24_pm.jpg

Fig. Position a suitable hydraulic jack under the front axle-F-150 4WD

2_14_2012_4_42_46_pm.jpg

Fig. Remove the upper front axle carrier mounting bushing bolt-F-150 4WD

2_14_2012_4_43_07_pm.jpg

Fig. Remove the axle shaft housing carrier bushing bolt-F-150 4WD

2_14_2012_4_43_29_pm.jpg

Fig. Remove the lower front axle carrier mounting bushing bolt-F-150 4WD

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day

Feb 14, 2012 | 2007 Ford F-150 Super

2 Answers

97 ford windstar leaking transmission fluid


Possible leaks are 1. Transmission belly Pan gasket 2. Front pump/torque converter seal. 3. Transmission fluid cooler lines 4. Axle seals at right and left half shafts.

Feb 13, 2012 | 1997 Ford Windstar

1 Answer

Torque setting for a 1998 ford taurus 3.0 intake manifold


TORQUE SPECIFICATIONSDescriptionNmLb-FtLb-InEngine Air Cleaner Tube Clamps1.6-2.2-14-19Engine Control Sensor Wiring Through Bolts2.5-3.5-23-30Generator to Bracket Bolt3727-Generator to Cylinder Head Bolt4835-Generator Brace to Upper Intake Manifold Bolts and Nut12-209-14-Intake Manifold Support to Throttle Body8-12-71-106Intake Manifold Support to RH Cylinder Head40-5530-40-Degas Tube to Upper Intake Manifold Bolts8-12-71-106Camshaft Sprocket to Camshaft Bolt50-7037-51-Camshaft Thrust Plate Bolt10-88Coil and Bracket to Cylinder Head Bolt40-5530-40-Connecting Rod Nut31-3923-28-Crankshaft Damper to Crankshaft Bolt125-16593-121-Crankshaft Pulley to Damper (4 Bolts)40-6030-44-Cylinder Head Retaining Bolt(1)(1)-Accelerator Cable Shield Bolts1.4-13Camshaft Position Sensor Housing Retaining Bolt2417-EGR Tube Connector to Exhaust Manifold40-4730-34-EGR Valve to Upper Intake Manifold Bolt20-3015-22-EGR Tube to EGR Valve and Exhaust Manifold35-6526-47-Exhaust Manifold Bolt/Stud20-2515-18-Flywheel to Crankshaft Bolt73-8754-64-Fuel Injection Supply Manifold to Intake Manifold8-12-71-106Throttle Cable Bracket1713-Dual Converter Y Pipe to Exhaust Manifolds34-4725-34-Crankshaft Position Sensor Bolts5-7-45-61Intake Manifold to Cylinder Head Bolt (5)(2)(2)-Main Bearing Cap Bolt75-8556-62-Oil Drain Plug11-169-11-Oil Filter Insert to Cylinder Block27-4020-29-Oil Filter to Oil Filter Adapter(3)(3)-Oil Galley and Cooling Jacket Plugs2014-Oil Level Indicator Tube to Exhaust Manifold Nut16-2012-14-Engine to Transaxle/Torque Converter Assembly Bolts40-6030-44-Torque Converter Nuts27-4620-33-Transmission Range Sensor Nut16-2212-16-Front Sub-Frame-to-Body Bolts77-10357-75-Oil Pressure Sensor16-2212-16-Oil Pump to Cylinder Block Bolt40-5530-40-Power Steering Bracket to Cylinder Head Bolt40-5530-40-Valve Cover to Cylinder Head Bolts/Studs (5)10-14-89-123Right Exhaust Manifold Heat Shield Retaining Bolts8-12-71-106Rocker Arm Seat to Cylinder Head Bolt(4)(4)-Water Outlet Connection to Intake Manifold Bolt10-14-89-123Upper Intake Manifold to Lower Intake Manifold Bolt/Stud20-3015-22-Engine Front Cover to Cylinder Block Bolt (No. 1-10)2518-Engine Front Cover to Cylinder Block Bolt (No. 11-15)10-88Water Pump Pulley to Hub (4 Bolts)20-3015-22-Water Pump to Front Cover Bolt8-12-71-106Wiring Retainer Bracket Nut20-3015-22-Valve Tappet Guide Plate to Cylinder Block10-14-89-123Ignition Coil Bracket40-5530-40-Oil Pan to Cylinder Block Bolt10-14-89-123Water Bypass Tube Nut20-3015-22-Crankshaft Pulley Bolts40-5530-40-


  1. Tighten in four steps (refer to illustration in Cylinder Head Installation for tightening sequence):
    • Tighten in sequence to 70-90 Nm (52-66 Lb-Ft)
    • Then back off all bolts 360 degrees
    • Tighten in sequence to 45-55 Nm (34-40 Lb-Ft)
    • Tighten in sequence to 85-99 Nm (63-73 Lb-Ft)
  2. Tighten in two steps
    • 20-30 Nm (15-22 Lb-Ft)
    • 26-32 Nm (20-23 Lb-Ft)
  3. Advance 3/4 to 1 turn after gasket contacts sealing surface or tighten to 13-15 Nm (10-11 Lb-Ft).
  4. Tighten in two steps:
    • 7-15 Nm (6-11 Lb-Ft)
    • 26-38 Nm (20-28 Lb-Ft)
  5. Refer to illustration in the Cylinder Head Installation procedure for tightening sequence.

Jan 10, 2012 | 1998 Ford Taurus

1 Answer

How to replace a 89 ford mustang 4 cylinder starter


  1. Disconnect the negative battery cable.
  2. Raise the front of the vehicle and install jackstands beneath the frame. Firmly apply the parking brake and place blocks in back of the rear wheels.
  3. Tag and disconnect the wiring at the starter.
  4. Remove the starter mounting bolts and remove the starter.
  5. Reverse the above procedure to install. Observe the following torques:

Dec 16, 2011 | 1989 Ford Mustang

2 Answers

My transmission leaks what should i replace


There are at least 5 places on the Automatic transmission that can over time, and mileage develope fluid leaks. Front converter seal at the front of the transmission,pan gasket in the center,dipstick tube o ring at the center on one side ,speed sensor o ring,and the tail shaft seal at the rear,of the transmission.
Place a flat piece or huge card board,under the engine and transmission,after driving you will see where the fluid,red in color is dripping. Its easier to spot exactly where the leak is comming if you can look under the car,while it is running, The easiest leak is the pan gasket,the dipstick tube, and the speed sensor,then the rear housing tail shaft bushing and seal.
If the front seal(converter seal) is leaking the transmission will need removed,and the seal,and maybe even the front pump bushing Replaced,it would be a good idea to replace the bushing esp if it has high mileage,80,000 or 100,000 miles of use.Change the fluid and the filter,while repareing the leak or leaks.Is a good idea.

Sep 17, 2010 | 1995 Chevrolet Camaro

4 Answers

83 mustang gt


In a 83 MUSTANG GT the correct answer is BOTH. As a 5.0L and a TURBO CHARGED 4 cyinder were offered.


1983 Mustang GT
  • Engine:
    • 5.0L horsepower increased to 175 HP when 4V carb replaced 2V carb from 1982 (Holley 4180C series).
    • Exhaust system was revised (less restrictive).
    • 4-speed SROD was only transmission available until early December 1982. In December, new 5-speed T5 became standard GT transmission (4-speed remained on option list).
    • Block and crank were revised to accomodate a 1-piece rear main seal in December 1982.
    • The new "Turbo GT" with a turbo charged 4 cylinder engine was available beginning late in the model year - 145 HP and featured the same suspension and other features of the V8 Mustang GT.

Jun 02, 2009 | 1983 Ford Mustang Hatchback

2 Answers

Front end problems


have you checked you brake rotors. they could be warped.

Sep 09, 2008 | 1997 Ford Thunderbird LX

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

246 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...