Question about 1994 Ford Taurus

1 Answer

Removed the heads need to adjust the valves need to know the torque

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 5,763 Answers

The torque specs for the valve are, step one is 97 inch lbs,
step two is 19-28 ft lbs.
Hope this helps.

Posted on Aug 24, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can anyone help? i need torque settings for head gasket and settings for inlet tappets and exusht


Find complete torque specs here:
http://fme-cat.com/LiveDocs/99999.pdf
and don't forget that you MUST buy new head bolts since they are torque to yield and MUST OT be reused!!

I suspect that you at least need to check the valve lash but as long as your head gasket is not dramatically different than original (which it should not be because that would change your compression ratio) you should be close to okay (I would check it). Or if you had any machine work done to the head, in which case you certainly would need to adjust the valve lash.

Feb 03, 2015 | 2005 Ford Focus

1 Answer

I need to know what torque i have to use to tight head bolt


-difference car with different torque. You need to look in its repair manual.

Good Luck

Mai

Nov 12, 2013 | 2006 Toyota Land Cruiser

1 Answer

Chevy van


Smoking issues after warm start up are usually caused by brittle valve stem seals and oil leaks down through the valve guide. These can be changed on the engine without head removal. Just use a air compressor to keep the cylinder full of air with the valves closed then remove the rocker arms counting the number of turns to keep adjustment. With a on car spring compressor remove spring. The valve keepers can be tight in retainer so tapping the retainer with released tension they will break free. Most chevy heads have 2 oil seals a hat type (positive spring seal) and a o-ring seal. With spring removed take both seals off there are very brittle. Replace the hat seal first then install spring with retainer. the o-ring seal needs to stay in retainer and in lower groove then install valve keepers and slowly release the spring pressure, Once spring compressor is removed then tap valve stem with hammer to seat keepers then release air. Also check Intake manifold bolts for proper torque. A loose manifold will also **** in oil bolt torque is 35-40 ft. lbs cast iron 30-35 ft. lbs aluminum manifold.

Nov 05, 2013 | 1992 Chevrolet G20

1 Answer

I need to know how to find/set timing marks for 2002 Kia Sedona and head bolt torque specs


The head bolt torque on a 2002 Kia Optima is 45 ft/lbs of torque. Always make sure you use a good torque wrench to get it right. ------------------------------------------------------------------------------------
Original Launch X431 Master

Mar 13, 2013 | Cars & Trucks

1 Answer

Lifter tap on a gmc sonoma 2.2 its a2001


U R GONNA NEED A FIELER GUADGE AND THE VALVE LASH SPEC REMOVE THE VALVE COVERS AND INSERT THE GUADGE BEWEEN THE ROCKER ARM AND VALVE SPRING AND TORQUE TO SPEC OR TAKE OFF VALVE COVER TAKE TWO PIECES OF CARDBOARD CUT THEM TO LENGTH OF THE HEAD INSERT ON TI THE HEAD SO U DONT SPASH OIL START TRUCK AND TURN EACH ROCKER UNTIL YOUR NOISE GOES AWAY BUT DO NOT OVER TORQUE U WILL KNOW THE ENGINE WILL BOGG DOWN

Jan 18, 2013 | 2001 GMC Sonoma Extended Cab

2 Answers

Valve lash procedure


i need to know how to adjust the valves on 02 pont sunfire

Nov 20, 2011 | 1991 Chevrolet K1500

1 Answer

Am put a new head set on my mustang 302 engine in no more compression y need a set up to adjust valve +


if you have everything installed correctly then these valves are a torque value that need a torque wrench to torque the rocker nut to specs.you don`t say if you have change from the factory style head assembly.

Jul 25, 2011 | 1986 Ford Mustang

1 Answer

How to adjust Ford 460 heads?


9 5 1 3 7 10 6 2 4 8 This is the head bolt sequence which should be torqued to 130-140 ft-lbs

Note: the numbers are represenative of the bolt location.

Mike...

Nov 24, 2009 | 1982 Ford F 250

Not finding what you are looking for?
1994 Ford Taurus Logo

Related Topics:

138 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

fordexpert

Level 3 Expert

5572 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...