Question about 1997 Chevrolet Lumina

1 Answer

Change front shock absorbers - 1997 Chevrolet Lumina

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,309 Answers

There are two methods, one is to replace the entire strut unit and the other just replaces the cartridge, both require special tools, best talk to your auto supplier to see what they offer, and you will need directions

Posted on Aug 24, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change 2007 dodge 1500 front struts?


Removal & Installation Independent Front Suspension – 2WD Vehicles To Remove:
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Safely raise and support the vehicle.
  3. Support the lower control arm outboard end.
  4. Remove or disconnect the following:
    • Upper shock absorber nut, retainer and grommet
    • Lower nuts and shock absorber
To Install:
  1. Install or connect the following:
    • Lower retainer and grommet on the shock absorber stud and insert shock absorber through frame bracket hole
    • Lower nuts
      1. Torque to: 25 ft. lbs. (34 Nm)
    • Upper grommet, retainer and new nut (or existing nut with Mopar Lock N Seal or Loctiti 242) on the shock absorber stud
      1. Torque to: 40 ft. lbs. (54 Nm)
  2. Remove support from lower control arm outboard end.
  3. Lower the vehicle.
Independent Front Suspension – 4WD Vehicles To Remove:
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Safely raise and support the vehicle.
  3. Remove tire and wheel assembly.
  4. Support the lower control arm outboard end.
  5. Remove or disconnect the following: dod_ram15_02-04_4wd_shock.gif

    • Upper shock nut with insulator and retainer
    • Lower shock bolt
    • Shock absorber
To Install:
  1. Install or connect the following:
    • Upper part of shock absorber into frame bracket with insulators and retainers and nut
      1. Torque to: 40 ft. lbs. (54 Nm)
    • Lower part of shock absorber into lower control arm with the bolt
      1. Torque to: 100 ft. lbs. (135 Nm)
  2. Remove support from lower control arm.
  3. Install tire and wheel assembly.
  4. Lower the vehicle.
Link/Coil Front Suspension To Remove:
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:
    • Nut, retainer, and grommet from upper stud in engine compartment dod_ram15_02-04_shock.gif

    • Nuts from upper shock bracket
  3. Lower bolt from axle bracket and shock absorber from engine compartment
To Install:
  1. Position lower retainer and grommet on upper stud and insert the shock through the spring from the engine compartment.
  2. Install or connect the following:
    • Lower bolt
      1. Torque to: 100 ft. lbs. (135 Nm)
    • Upper shock bracket and nuts
      1. Torque to: 55 ft. lbs. (75 Nm)
    • Upper grommet, retainer and upper shock absorber nut
      1. Torque to: 35 ft. lbs. (47 Nm)
prev.gif next.gif

Jul 22, 2010 | 2007 Dodge Ram Truck

2 Answers

What is service ride control


Service Ride Control means one or some of your shocks or struts are worn and may need replacing. The price for new ones is not cheap,

Jul 13, 2010 | 2006 Cadillac Escalade

1 Answer

How do I change the front and rear shocks on my 99 cherokee?


FRONT:
Removal & Installation
  1. Remove the nut, retainer and grommet from the shock stud in the engine compartment.
  2. Raise and support the front axle.
  3. Remove the lower mounting nuts from the axle bracket.
  4. Remove the shock absorber.
To install:
  1. Position the lower retainer and grommet on the shock stud. Insert the shock absorber through the shock tower hole.
  2. Install the lower shock studs into the axle bracket.
  3. Install the mounting nuts and tighten to 250 in. lbs. (28 Nm).
  4. Remove support and lower the vehicle.
  5. Install the upper grommet, retainer and nut on the stud in the engine compartment.
Rear:

Removal & Installation
  1. Before servicing the vehicle, please familiarize yourself with safety procedures.
  2. Remove or disconnect the following:
    • Upper locknut and washer from the frame bracket stud, on the Grand Cherokee
    • Lower bolt, nut and washers from the axle shaft tube bracket
    • Shock absorber
To install:
  1. Place the shock absorber upper end in position and tighten the fasteners to the following specifications:
    • Cherokee: 17 ft. lbs. (23 Nm)
    • 1999–01 Grand Cherokee:68 ft. lbs. (92 Nm)
    • 2002–04 Grand Cherokee: 80 ft. lbs. (108 Nm).
    • 2005 Grand Cherokee: 70 ft. lbs. (95 Nm).
  2. Place the shock absorber lower end in position and tighten the fasteners to the following specifications:
    • Cherokee: 46 ft. lbs. (62 Nm)
    • 1999–01 Grand Cherokee:68 ft. lbs. (92 Nm)
    • 2002–05 Grand Cherokee: 115 Nm (85 Nm).
    please do not hesitate to ask any further questions about your vehicle i would be glad to help you.
  3. do not forget to rate and comment about your experience with fixya...


Dec 27, 2009 | 1999 Jeep Cherokee

1 Answer

How to replace front shock bsorbers


This is for the 2WD model:

2-Wheel Drive
  1. Raise and support the front of the vehicle safely using jack stands.
  2. Using an open end wrench, hold the shock absorber upper stem to prevent it from turning, then remove the upper stem retaining nut, the retainer and rubber grommet.
c16056c.gif
Common front shock absorber mounting-2WD vehicles

  1. Remove the shock absorber-to-lower control arm retaining bolts and lower the shock absorber assembly from the bottom of the control arm.
  2. Inspect and test the shock absorber; replace it, if necessary.
To install:
  1. Fully extend the shock absorber stem, then push it up through the lower control arm and spring so that the upper stem passes through the mounting hole in the upper control arm frame bracket.
  2. Install the upper shock absorber nut and tighten to 100 inch. lbs. (11 Nm) on 1994 models 145 inch lbs. (16 Nm) on 1995 models, 54 ft. lbs. (73 Nm) on 1996 models, or 106 inch lbs. (12 Nm) on 1997-99 models while holding the stem with an open end wrench. Be careful not to crush the rubber bushing.
  3. Install the shock absorber-to-lower control arm retaining bolts and tighten to 20 ft. lbs. (27 Nm) on 1994-95 models and 54 ft. lbs. (73 Nm) on 1996 models, or 22 ft. lbs. (30 Nm) on 1997-99 models.
  4. Remove the jack stands and carefully lower the vehicle.

Nov 01, 2009 | 1998 Chevrolet S-10 Pickup

1 Answer

Shocks


rear
5955ba5.gif ------------------------------------------------------------------------------------------

front

Removal
  1. Remove front shock absorber-to-upper shock bracket nut and bolt.
  1. Disconnect the lower end of the front shock absorber bolt and nut from the U-bolt plate.
  1. Compress the front shock absorber and remove.
Installation
  1. Insert front shock absorber into the front shock absorber mounting bracket (18183). Insert bolt and tighten nut to 60-81 Nm (45-60 lb-ft).
  1. Attach the lower end of the front shock absorber to the U-bolt plate by installing the nut and bolt. Tighten to 60-81 Nm (45-60 lb-ft).
---------------------------------------------------------------------------------------------

front


Feb 04, 2009 | 1996 Ford F350 Crew Cab

1 Answer

How to take off & install front shocks on a 2002 Chevrolet S-10


NOTE Hold the shock absorber stem with a wrench while backing the nut off.
Wheel Mounting nut


Retaining nut and grommet Shock absorber-to-lower control arm bolts Shock absorber Replace the parts, as necessary.

0900c1528024dc58.jpg enlarge_icon.gifenlarge_tooltip.gifFig. Front shock absorber mounting-2WD vehicles


To install:
  1. Fully extend the shock absorber stem, then push it up through thelower control arm and spring so that the upper stem passes through themounting hole in the upper control arm frame bracket.
  2. Install or connect the following:

    Retaining nut and grommet on the stem. Tighten the nut to 106 inch lbs. (12 Nm).


    Shock absorber-to-lower control arm bolts and tighten to 22 ft. lbs. (30 Nm) Wheel

Oct 17, 2008 | 2001 Chevrolet S-10

1 Answer

Shock absorber


kyb shocks ar the best thats all we use also check the "ruber" on the top make sure it is compresed together any gaps cause the " bump or pounding" noise

Sep 18, 2008 | 1997 Chevrolet Suburban

1 Answer

SHOCK ABSORBER LIGHT


The shocks are electronic and very expensive. Changed mine last year, the fronts were $87.00 each and thr rear $125.00 each. They could only be purchased from the dealer. Haven't seen any online. They have a connection at the top that monitors the pressure or something.

Aug 17, 2008 | 2002 Isuzu Axiom

Not finding what you are looking for?
1997 Chevrolet Lumina Logo

Related Topics:

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...