Question about 2006 Toyota Corolla

1 Answer

A/C stopped working. Nothing turns on when the A/C switch is pushed. I checked to fuse, it is OK.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 46 Answers

There could be more than one fuse or the contacts could be bad in the switch

Posted on Aug 24, 2010

Testimonial: "OK, thanks. I'll check into that."

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does nothing at all happen when hazard switch is pushed in to on position?


If your Hazard lights flash when you turn them on then it could possibly be the bulb behind the Hazard Button. There is a tiny bulb behind the switch to indicate when it is turned on. This bulb has possibly burned out and is in need of replacement. If your Hazard lights don't flash when pushing the switch it could possibly be that somewhere along your four flasher lamps there is a bad bulb or maybe more. Since you've checked the fuses and came to the conclusion that all were fine.

Dec 05, 2015 | Cars & Trucks

2 Answers

How to fix Cruise Control


The most common problem on this vehicle is the sensor right on the master brake cylinder the seal goes out and brake fluid gets right in the sensor ruining it that is the most common problem lete no if it helps

Sep 22, 2014 | 2001 Ford Windstar

1 Answer

Honda CRV Keyless Entry stopped working. Pushing any button on either remote does nothing. They both just stopped working at the same time out of the blue. All doors function properly from inside


Check the batteries in the remotes. It might just be a massive coincidence and the 2 stopped working at the same time. Failing that I would guess the reciever is the problem

Dec 04, 2012 | BMW X5 Series Cars & Trucks

1 Answer

My break light fuse keeps blowing in my 97 suburban any ideas why


Assuming it's a K1500, 15A STOP/HAZ fuse 1 in the instrument panel fuse block is the source of power. If the stop lamp switch checks OK, and the center high mount stop lamp is OK, the cruise control system gets input at this point and may be defective. Fuse 1 also feeds power through the turn/hazard switch to the stop filaments of the tail/stop/turn lamps and these presumably are OK

Sep 22, 2012 | 1997 Chevrolet Suburban

2 Answers

I have a 2000 chevy 2500 and the tail lights, tag lights and brake lights have stopped working, I checked the bulbs and they are good, fuses are good. Have not replaced the brake relay under the hood. Do I...


check for power at the wires going intop the tail lights, real common that the circuit board is bad, but unlikely both at the same time. The tag, tail lights and brakes are 2 different systems. Do the turn signals work normally? if so the wiring from the turn signal switch to the brake lights is GOOD. the stop light switch had\s a ORANGE wire that should have 12V if not ck STOP LPS fuse, when brake pedal is depressed, the WHITE wire is 12V (at the stop light switch) if that is OK, the turn signal switch COULD be bad. The wiring harness plug is near the back left under the tailgate, see if that is disconnected?

Aug 04, 2011 | 1999 Chevrolet K2500

2 Answers

Brake lightswill not work aven after changing Bulbs. What could be the problem?


Need to check the brake light switch. ok down by the brake pedal there is a switch that tells the lights to turn on when you push it. almost always easy to fix and you can buy a switch aftermarket for around $10 bucks. If you have cruse control a good way to check the switch is to run the cruse con and try to get it to stop crusing by pushing the brake pedal if it keeps going thats your problem. hope this helps

Aug 20, 2009 | 1995 Pontiac Sunfire

1 Answer

The turning signals and heater blower dont work on my 99 mystique


when checking fuses pull one and check the wire lead or flat metal lead going from side to side of the fuse if you dont see a burn or dark spot its ok replace it and continue this until you have found the bad ones of check your bulbs sometime a bad bulb will not let the others work properly.If these do not work chect your signal switch also known as a multifunction switch.I would not attempt to chang the blower if its not a fuse because they can be hazerdly.

Mar 30, 2009 | 1999 Mercury Mystique

1 Answer

Brake lighs stop working


Does the 3rd brake lamp illuminate? If so then your problem is multifunction switch.If it doesn't do the following checks.
Check for power to and thru the brake lamp switch itself.If you do not have power to the switch check fuse no. 10(20 amp) in the interior fuse panel.If you have power to the switch then depress brake pedal and make sure you have power thru the switch.If this is ok the check Fuse 22(20amp) with brake applied..

Mar 01, 2009 | 1999 Lincoln Town Car

1 Answer

1989 toyota camry blower just stopped


find your fuse layout or owners manual and check the fuse and replace it even if it looks ok,thencheck to see if the switch itself is bad,if so replace it by removing the screws,(4-6) and dash cover checking the connection and switch,replace which ever one is bad and turn on the car,turn one the switch if nothing happens the switch is bad replace and enjoy!

May 18, 2008 | 1989 Toyota Camry

Not finding what you are looking for?
2006 Toyota Corolla Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...