Question about 1996 Ford Ranger SuperCab

1 Answer

How do you replace the vehicle speed sensor on a 1996 Ford Ranger 4.0 L V-6?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    MVP:

    An expert that gotĀ 5 achievements.

    Master:

    An expert who has achieved Level 3.

    Sergeant:

    An expert that hasĀ over 500 points.

  • Master
  • 450 Answers

The speed sensor is located on the tranny it has a blue coler

Posted on Aug 24, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of vaccum modulator valve on a 99 ford ranger


There isn't one , transmission is controlled electrically . If it doesn't shift right have it checked for DTC's - diagnostic trouble codes . Does the speedometer work ? VSS - vehicle speed sensor , input speed sensor .

Dec 21, 2016 | Ford Ranger Cars & Trucks

2 Answers

Need to reset ABS light on 1996 Ford Ranger


Maybe you have a bad speed sensor, its a shot in the dark but that sensor controls a lot of functions like the ABS, speedometer, check engine light can come on, automatics will shift hard or may not shift at all, o/d will flash. The video below shows a 1999 ford ranger automatic but if you check you might have the same sensor.

Feb 09, 2014 | 1996 Ford Ranger SuperCab

1 Answer

Repair speedomoter 1996 ford ranger manual shift transmission


could be a vehicle speed sensor, Is your check engine light on since this problem arose, and could also be the speedo itself going bad.

Dec 19, 2012 | 1996 Ford Ranger SuperCab

1 Answer

Where does a evap sensor go in a 1996 ranger pickup


I'm not an expert and I have a similar problem on the 1996 Mazda extended PU w/2300 four cylinder. Same vehicle, made in ranger plant in NJ.

On the four, the purge solenoid and the purge flow sensor are located just aft (towards driver) of the battery on a vac line between the canister (next to the battery) and the intake (Just forward of the brake master cylinder.

QUESTION: Is there a pressure sensor in the fuel tank of this vehicle??????

Sep 22, 2012 | 1996 Ford Ranger SuperCab

1 Answer

1996 ford ranger obd2 code 0402


check your egr valve its probably stuck open from carbon buildup and is letting too much exhaust recirculate you can take these off and clean them but with the age of your vehicle i would replace it

there is also a sensor that measures this that sometimes fails its called DPFE sensor it measures the amount of exhaust that is recirculate

not knowing what engine you have its hard to tell you ware the egr and DPFE sensor is located

May 17, 2009 | 1996 Ford Ranger SuperCab

1 Answer

1996 Ford Ranger SuperCab every time I crank my ranger, the engine rev really high. After running for a couple minutes, it begins to slow down to idle speed. Also, if the vehicle is put in gear while high...


With out a check engine code there could be few things that can do this, clean the mass air flow sensor, check your engine air cleaner and then if this doesn't help, have someone start the car while you watch the throttle linkages, after it warms up watch which linkage moves when the engine speed drops this will be connected to the problem sensor / auto choke. Try unplugging it to see if it helps before you go out and buy a new one.
I hope this helps
Sam

May 14, 2009 | 1996 Ford Ranger SuperCab

3 Answers

Where is the ignition module control located on 1996 ranger 2.3 e


It does not have an ignition control module. The PCM (powertrain control module) fires the coil pack based on signal it recieves from the crankshaft position sensor and the camshaft position sensor.

Apr 08, 2009 | 1996 Ford Ranger SuperCab

1 Answer

SPEEDOMETER


I believe that would be the VSS or vehicle speed sensor.. Its located on the rear axle.. I would get the part directly from a ford dealer as the one I got from an auto parts store did not work correctly.. It cost about 33 dollars from ford and It is an easy change for a do it yourself person.. Kip

Jun 18, 2008 | 1998 Ford Ranger SuperCab

Not finding what you are looking for?
1996 Ford Ranger SuperCab Logo

Related Topics:

254 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...