Question about 2004 Dodge Ram 1500

1 Answer

Push rod came loose on the back driver side i beleave its #7 i took the rocker arm thing off and all the sprins on the head are tight except that one i took and taped on it a little and it went down and stayed. the truck would crank but was running real rough.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,092 Answers

Run's with miss, due to # 7 cylinder valve is stuck open, no compression, could be valve seat that's come loose, ether way the cylinder head will have to be remove to repair (valve job), need to get it done a.s.p, because if valve fall's into cylinder, will cause piston damage.

Posted on Aug 24, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I'm still having problem after setting tappets car runs after + - 30k ,makes a tappet noise just one push rod and rocker runs loose but nuts are all tight on the rocker, plz if can advise me regards


Hard to help much without knowing what type of vehicle you are working on, but I would suggest pulling the rocker and making a mark with a sharpie or paint and re-installing everything tight. Run the engine until you get the rattle back, then check the mark to see if the rocker stud is coming out of the head.

Oct 06, 2016 | Cars & Trucks

1 Answer

Torque settings for rocker shaft for a 1998 7k toyota 1800


There is no such thing as a rocker shaft. There is a cam shaft, rocker arm assembly, Rocker arm, lifter etc. If you are talking about the rocker arm assembly that bolts to the head, it is 58 Ft/lbs. If you are talking about the actual rocker arms, you tighten them till they contact the push rod and the valve stem and then you put oil control clips on so the oil does not spray and you start the engine. You tighten them down till the chattering noise goes away, then back them off 1/8 to 1/4 turn.

Apr 25, 2014 | 1995 Toyota Corolla

1 Answer

Push rod diagram


Exhaust push rods are longer
  • 6.0740 Inch Overall Length
  • Standard Size
  • Intake valves are
  • 5.7460 Inch Overall Length
  • Standard Size. Front head.
front head standing in front of car passenger to driver side
Ex , in ,in Ex ,in Ex

rear head standing in front of car passenger to driver side
Ex. ,In , Ex , In , In , Ex

remember exhaust push rods are longer
Rocker arm bolt ................................ 124 lb. in.plus 30 degrees

Apr 21, 2014 | 1999 Pontiac Grand Am GT

1 Answer

Bad rocker arm


could be lifter not charging of oil.it is not adjustable. or push rod out of lifter

Sep 20, 2013 | Pontiac Grand Prix Cars & Trucks

1 Answer

I have a tundra 06 an it does a cliking sound .it comes from the motor. i check everything around the motor and nothing is loose i wonder if there is something loose inside.


The problem is probably a loose rocker arm or a broken rod. You can easily access the rocker arms by taking top cover off the engine. It should be 6 or 8 bolts and looks like an upside down bread loaf pan. There will be a little bit of oil (assuming the engine is off) but it shouldn't be too messy. There will be a number of rockers which are levers with springs on one side. One bolt should hold down each rocker, just make sure that none of them are loose. Since it is a "V" engine (V6 or V8) there will be two of these covers, half of the rockers under each one.

If all of the rockers are tight (don't crank them down excessively just check to see if one is very loose). then it might be a broken rod. To remove the rod you need to remove the rocker arms one at a time and pull out the rod with a special tool that you can probably get from your local parts store. When you find it they can also sell you a replacement rod.

If you want to narrow it down you can turn the engine on with one sides cover off (but hold a paper towel over the rockers or you will get sprayed with oil) and listen to see if you can hear which one is broken.

Jun 09, 2011 | Toyota Tundra Cars & Trucks

1 Answer

2001 grand cherokee 4.0l valve rocker torque specs


5 million made.
it's in the fsm book
posted here over 300 times.
are you asking , how to set rockers ?

chapter 9 page 27
------------------text fsm---------------------
INSPECTION
Inspect the pivot surface area of each rocker arm.
Replace any that are scuffed, pitted, cracked or
excessively worn.
Inspect the valve stem tip contact surface of each
rocker arm and replace any rocker arm that is deeply
pitted.
Inspect each push rod end for excessive wear and
replace as required. If any push rod is excessively
worn because of lack of oil, replace it and inspect the
corresponding hydraulic tappet for excessive wear.
Inspect the push rods for straightness by rolling
them on a flat surface or by shining a light between
the push rod and the flat surface.
A wear pattern along the length of the push rod is
not normal. Inspect the engine cylinder head for
obstruction if this condition exists.
INSTALLATION
NOTE: This procedure can be done with the engine
in or out of the vehicle.
(1) Lubricate the ball ends of the push rods with
Mopart Engine Oil Supplement, or equivalent and
install push rods in their original locations. Ensure
that the bottom end of each push rod is centered in
the tappet plunger cap seat.
(2) Using Mopart Engine Oil Supplement, or
equivalent, lubricate the area of the rocker arm that
the pivot contacts. Install rocker arms, pivots and
bridge above each cylinder in their originally position
(Fig. 23).
(3) Loosely install the capscrews through each
bridge.
(4) At each bridge, tighten the capscrews alternately,
one turn at a time, to avoid damaging the
bridge. Tighten the capscrews to 28 N·m (21 ft. lbs.)
torque.
(5) Install the engine cylinder head cover (Refer to
9 - ENGINE/CYLINDER HEAD/CYLINDER HEAD
COVER(S) - INSTALLATION).

Mar 13, 2011 | Jeep Grand Cherokee Cars & Trucks

1 Answer

I need a print out of how i can change out a head gasket on a 1995 mercury cougar


Removal
  1. Drain engine cooling system.
  1. Disconnect battery ground cable (14301) .
  1. Remove engine air cleaner (ACL) (9600) including air cleaner outlet tube (9B659) .
  1. Loosen drive belt tensioner (6B209). Remove drive belts (8620) .
  1. If LH cylinder head (6049) is being removed, perform the following:
    1. Remove oil filler cap (6766) .
    1. Remove power steering pump front mounting bracket retaining bolts.
    1. Remove generator (GEN) (10346) and belt idler pulley (8678).
    1. Remove power steering pump/generator bracket retaining bolts. Leave hoses connected, place pump/bracket assembly aside in a position to prevent fluid from leaking out.
  1. If RH cylinder head is being removed, perform the following:
    1. Remove drive belts .
    1. If equipped with A/C, remove mounting bracket retaining bolts. Leave hoses connected and position A/C compressor (19703) aside.
    1. Remove positive crankcase ventilation valve (PCV valve) (6A666) .
  1. Remove upper intake manifold (9424) .
  1. Remove valve cover retaining bolts.
  1. Remove fuel injection supply manifold (9F792).
  1. Remove lower intake manifold as outlined.
  1. Remove exhaust manifolds (9430) as outlined.
  1. Loosen rocker arm seat retaining bolts enough to allow rocker arm (6564) to be lifted off the push rod (6565) and rotate to one side.
  1. Remove push rods . Identify position of each push rod . Push rods should be installed in their original position during assembly.
  1. Remove cylinder head retaining bolts and discard.
  1. Remove cylinder heads .
  1. Remove and discard old head gaskets (6051) .
Installation
  1. NOTE: Lightly oil all bolts and stud bolt threads before installation except those specifying special sealant.
    Clean cylinder head, intake manifold , valve cover (6582) and head gasket surfaces. If cylinder head was removed for head gasket replacement, check flatness and sealing areas for scratches of cylinder head and cylinder block gasket surfaces. Refer to Section 03-00 for procedure.
  2. Position new head gaskets onto cylinder block (6010) using cylinder head to block dowels (6A008) for alignment.

    Head Gasket


    a11431c.gif

  3. Position cylinder heads onto cylinder block .
  4. ani_caut.gif CAUTION: Always use new cylinder head bolts to ensure a leak-tight assembly. Torque retention with used bolts can vary, which may result in coolant or compression leakage at the cylinder head mating surface area.
    -ft).
  5. For 3.8L non-SC engine, tighten cylinder head retaining bolts in numerical sequence in three steps as follows:
    1. 20 Nm (15 Lb-Ft)
    1. 40 Nm (29 Lb-Ft)
    1. 50 Nm (37 Lb-Ft)
  6. ani_caut.gif CAUTION: Do not loosen all of the bolts at the same time, only work on one bolt at a time or possible damage to engine or leakage may occur.
    In sequence, loosen retaining bolts two to three revolutions and retighten bolts one at a time in the following manner:
    1. Long bolts:
      • 15-25 Nm (11-18 lb-ft).
      • Tighten bolt an additional 85-95 degrees.
      • Go to next bolt in sequence.
    1. Short bolts:
      • 10-20 Nm (7-15 lb-ft).
      • Tighten bolt an additional 85-95 degrees.
      • Go to next bolt in sequence.


      a11399c.gif


      Item Part Number Description 1 6010 Cylinder Block 2 - Locating Pin (2 Req'd) 3 N802515-S Cylinder Head Bolt (4 Req'd Each Side) 4 6049 Cylinder Head 5 N802516-S Cylinder Head Bolt (4 Req'd Each Side) 6 6A008 Cylinder Head to Block Dowel
  7. NOTE: If original valve train components are being installed, a valve clearance check is not required. If a component has been replaced, perform a valve clearance check as outlined.
    Dip each push rod end in Engine Assembly Lubricant D9AZ-19579-D or equivalent meeting Ford Specification ESR-M99C80-A and install push rods in their original position.
  8. For each valve, rotate crankshaft (6303) until valve tappet (6500) rests on the heel (base circle) of the camshaft lobe, before tightening rocker arm seat retaining bolts to 7-15 Nm (5-11 lb-ft) maximum.
  9. Lubricate all rocker arms with Engine Assembly Lubricant D9AZ-19579-D or equivalent meeting Ford Specification ESR-M99C80-A. Final-tighten the rocker arm seat bolts to 30-40 Nm (22-30 lb-ft). For final tightening, camshaft (6250) may be in any position.
  10. Install exhaust manifolds as outlined.
  11. Install lower intake manifold as outlined.
  12. Install fuel injection supply manifold .
  13. Position valve cover and new valve cover gasket (6584) on cylinder head and install retaining bolts. Note location of ignition wire routing clip stud bolts. Tighten retaining bolts to 9-12 Nm (7-9 lb-ft).
  14. Install upper intake manifold .Install spark plugs (12405) , if removed.
  15. Connect ignition wires to the spark plugs .
  16. If LH cylinder head is being installed, perform the following:
    1. Install oil filler cap.
    1. Install generator/power steering pump mounting bracket.
    1. Install generator .
    1. Install main accessory drive belt tensioner .
    1. Install power steering pump (3A674) .
    1. Install power steering pump support bracket.If RH cylinder head is being installed, perform the following:
    1. Install positive crankcase ventilation valve .
    1. If equipped with A/C, install A/C compressor mounting brackets (2882) and A/C compressor .
  17. Install drive belt and tighten to specification.
  18. Connect battery ground cable .
  19. Install air cleaner outlet tube.
2010&c18=modelyear&c35=wsm%2ccylinder%20heads%2cssd%2c03-01a%2cin-vehicle%20service&s=1249x702&c=32&j=1.3&v=y&k=y&bw=910&bh=359&ct=lan&hp=n&[aqe]

Mar 06, 2011 | Mercury Cougar Cars & Trucks

2 Answers

Rocker arm come out on jeep chrysler 3.7 eng


A rocker arm is the arm that sits on top of the valve stem and connects to the push rods 'the push rods sit on the cam so when engine is running, the push rods go up and down in a timed sequence and with the rocker arms, open and close the inlet and exhaust valves. the rocker arm is located inside the valve(rocker)cover .If the rocker arm gets loose or comes out.
Check the nuts on the shaft which holds the rocker arms.either the shaft or nuts are got loose.They need to be tightened.Don't make it too tight or too loose.  Too tight,and they don't flutter right. Too loose,and they allow the rocker arms to wiggle out of whack. Other possibility can be  something is broken, bent, collapsed, or out of adjustment. 
Thanks. you can rate this solution and show your appreciation.



May 20, 2010 | 2002 Jeep Liberty

1 Answer

Roker Arms


First off, do not overtighten the rocker. You will not make it any tighter and you run the risk of damaging that stud or the rocker. Compare the valve stem height to the other valve stems of the same valve type (exhaust or intake). If it's lower, you may have a broken spring or a stuck valve. Check the push rod against the other push rods, again from the same valve type. If it's lower, and your push rod is OK as you say, you may have a damaged lifter.

Aug 17, 2008 | 1993 Oldsmobile Cutlass Ciera

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

114 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...