Question about 1990 Toyota Camry

1 Answer

How do i remove the thermostat in my car radiator

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    MVP:

    An expert that gotĀ 5 achievements.

    Master:

    An expert who has achieved Level 3.

    Sergeant:

    An expert that hasĀ over 500 points.

  • Master
  • 465 Answers

Follow the top hose and it will lead you to the houseing located on the motor

Posted on Aug 24, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change thermostat on a 2005 kia sedona


  1. Drain the coolant
  2. The thermostat is located at the end of the top radiator hose. Remove the drain plug from the radiator and flush the coolant into a pan.
  3. Remove the Upper radiator hose
  4. Loosen the clamps that connect the upper radiator hose to the housing and remove the hose.
  5. Remove the thermostat housing
  6. Loosen the thermostat housing mounting bolts. Remove the housing and pull the thermostat from it.
  7. Replace the thermostat
  8. Inspect the new thermostat and install it with a new gasket. Mount the housing and upper radiator hose. Then pour new coolant into the radiator.

Mar 18, 2017 | 2005 Kia Sedona

2 Answers

HOW TO FLUSH AND RENEW COOLANT?


if the thermostat is in the head at the top radiator hose , remove it an fill the cooling system until the water is at that point --refit the thermostat and continue filling
make sure that the heater is turned on so that any air is moved out of the system

May 30, 2016 | Cars & Trucks

1 Answer

Thermostat replacement 1996 Lincoln town car


Instructions
    • 1 Place a large drain pan beneath the radiator drain on the passenger side of the Town Car. Open the hood and remove the radiator cap.
    • 2 Loosen the radiator drain plug using a wrench. Wait until the coolant is below the level of the upper radiator hose.
    • Sponsored Links
    • 3 Trace the upper radiator hose to the thermostat housing. Loosen the hose clamp on the housing with a flat-blade screwdriver. Slide the clamp back and remove the hose from the housing. Use a wrench to remove the two mounting bolts from the thermostat housing.
    • 4 Slide the housing off of the intake manifold. Clean any remaining gasket pieces from the thermostat housing with a flat scraper and clean rag. Remove the old thermostat from the housing.
    • 5 Insert the new thermostat into the housing. Position the new gasket on the outer edge of the housing and position it over the mounting area on the intake manifold. Replace the two mounting bolts and tighten them using a wrench.
    • 6 Replace the upper radiator hose on the thermostat housing and tighten the hose clamp. Top off the radiator with a blend of equal parts antifreeze and distilled water. Replace the radiator cap.


Read more : http://www.ehow.com/how_6319041_change-1996-lincoln-town-car.html

Mar 03, 2015 | 1997 Lincoln Town Car

2 Answers

Engine Diagrams


Hello. Here a non-photo diagram. Hope this helps!!!

The thermostat is located on the side of the water pump, the water pump is located just above the a/c compressor, the thermostat is fed coolant from the radiators lower radiator hose.
Thermostat :
1. drain coolant and tighten drain plug ( easier method : remove radiator cap, get big drain pan, place drain pan under lower radiator hose to radiator connection, remove clamp, slowly remove hose, allow coolant to drain into pan, now is a good time to remove radiator hose and clamp from thermostat housing )
2. remove thermostat cover / cap ( easiest to get at this when front of car is supported by jack stands and right hand side lower cover is removed ).
3. thermostat cap is held on by 3 bolts / remove thermostat.

You will notice that the thermostat's air bleed hole is pointing up and lines up with notch in water pump housing,,

ATTENTION :failure to install new thermostat in the correct location will cause engine to overheat.

1. install new thermostat to water pump, make sure air bleed hole lines up with notch, install and tighten bolts, install a new lower radiator hose, fill cooling system.

thermostat # 17670-77E00
lower radiator hose #17854-65G20
hose clamp #09401-36403
upper radiator hose # 17852-65G20

Suzuki factory manual

Oct 21, 2013 | Cars & Trucks

1 Answer

Thermastat diagram install


Thermostat - 3.0L (2V) Removal and Installation
  1. Partially drain the engine cooling system. For additional information, refer to COOLING SYSTEM DRAINING, FILLING AND BLEEDING .
  2. Remove the three thermostat housing bolts. Fig. 25: Removing Thermostat Housing Bolts
    Courtesy of FORD MOTOR CO.

  3. Remove the thermostat O-ring seal.
  4. To install, reverse the removal procedure.
Thermostat - 3.0L (4V) Removal and Installation
  1. Raise and support vehicle. For additional information, refer to JACKING & HOISTING .
  2. Remove the front splash shield. For additional information, refer to FRONT END BODY PANELS .
  3. Drain the cooling system. For additional information, refer to COOLING SYSTEM DRAINING, FILLING AND BLEEDING .
  4. Remove the cooling tube bolt. Fig. 27: Removing Cooling Tube Bolt
    Courtesy of FORD MOTOR CO.

  5. Lower the vehicle.
  6. Remove the radiator upper cooling tube bolt. Fig. 28: Removing Radiator Upper Cooling Tube Bolt
    Courtesy of FORD MOTOR CO.

  7. Disconnect the upper radiator hose and engine vent hose. Fig. 29: Disconnecting Upper Radiator Hose And Engine Vent Hose
    Courtesy of FORD MOTOR CO.

  8. Remove the two bolts, and separate the radiator tube from the thermostat housing. Remove the thermostat. Fig. 30: Removing Bolts And Separating Radiator Tube From Thermostat Housing
    Courtesy of FORD MOTOR CO.

  9. To install, reverse the removal procedure.

Apr 22, 2012 | 2002 Ford Taurus

3 Answers

How do i change a thermostat ona 2004 jeep liberty with a 3.7 engine


Disconnect neg batt cable, drain cooling system, loosen lug nuts passenger side, jack up Jeep and use jack stands, remove flap inside wheel well, remove lower radiator hose at engine, remove thermostat cover and take out thermostat and replace.12_29_2011_3_18_38_pm.jpg

Dec 29, 2011 | 2004 Jeep Liberty

2 Answers

Where is thermostat on my 2005 chevy classic


Thermostat Removal & Installation 2.2L Engine 2004-2005 To Remove:
  1. Drain the cooling system. chevy_cav_02-04_tstat.gif
  2. Remove the thermostat housing-to-water pump feed pipe bolts. chevy_cav_02-04_feedpipe.gif
  3. Remove the water pump feed pipe from the thermostat housing .
  4. Remove the thermostat from the housing.
To Install:
  1. Install the thermostat on the housing.
  2. Install the water pump feed pipe on the thermostat housing with the mounting bolts. Tighten 89 in-lb (10 Nm).
  3. Fill the cooling system.
2006-2007 To Remove:
  1. Drain the cooling system.
  2. Disconnect the radiator outlet hose from the surge tank and thermostat housing cover. Thermostat & cover gm-03-39-3601.gif
  3. Remove the mounting bolts and remove the thermostat housing cover.
  4. Remove the thermostat from the housing. Discard the O-ring.
To Install:
  1. Using a new O-ring, install the thermostat on the housing.
  2. Install the thermostat housing cover with the mounting bolts. Tighten 89 in-lb (10 Nm).
  3. Connect the radiator outlet hose to the surge tank and thermostat housing cover.
  4. Fill the cooling system.
3.5L Engine (LZ4) W/ Variable Valve Timing & 3.9L Engine To Remove:
  1. Drain the cooling system.
  2. Remove the air cleaner outlet duct.
  3. Disconnect the radiator outlet hose from the thermostat housing. Thermostat 3.9L gm-03-00-3054.gif
  4. Remove the mounting bolt/stud and remove the thermostat housing.
  5. Remove the thermostat from the engine.
  6. Clean the sealing surfaces.
To Install:
  1. Using a new gasket, install the thermostat on the engine.
  2. Install the thermostat housing with the mounting bolts. Tighten 89 in-lb (10 Nm).
  3. Connect the radiator outlet hose to the thermostat housing.
  4. Install the air cleaner outlet duct.
  5. Fill the cooling system.
  6. Check the cooling system for leaks.
3.5L Engine (LX9) W/O Variable Valve Timing To Remove:
  1. Drain the coolant.
  2. Disconnect the radiator hose from the thermostat housing. Thermostat 3.5L gm_mv_ven_tstat.gif
  3. Remove the mounting bolt/stud and remove the thermostat housing.
  4. Remove the housing gasket.
  5. Remove the thermostat.
  6. Clean the mating surfaces.
To Install:
  1. Install the thermostat on the engine.
  2. Install the thermostat housing and gasket with the mounting bolts. Tighten 18 ft-lb (25 Nm).
  3. Connect the radiator hose to the thermostat housing.
  4. Fill the cooling system.
  5. Check the cooling system for leaks.

Jan 29, 2011 | 2005 Chevrolet Malibu

2 Answers

Where is the thermostat located


Under the hood find radiator at front of the car on either left or right side of radiator is a fat hose that will be connected to the radiator. Follow that hose to the engine and it connects to the thermostat cover that is connected to the top of the engine with two bolts holding it on. Remove both bolts, Remove thermostat cover replace with new thermostat, Scrap off old gasket on both connecting sides place in new gasket (using a gasket sealer with the gasket wouldn't hurt to) replace both bolts only SNUG tight if using sealer let sit for a hour or two. your done!!

Jan 25, 2011 | 1998 Mercury Sable

2 Answers

2004 thermostat where is it located on engine



2.2L (VIN 4) Engine

  1. Drain the cooling system.
  2. Remove the lower radiator hose from thermostat outlet.

    67ec47f.jpg
    Fig. Remove the thermostat outlet bolts and outlet
  3. Remove the thermostat outlet bolts and outlet.

    77bb8c2.jpg
    Fig. Remove the thermostat



2.2L (VIN F) Engine
  1. Remove the thermostat housing to water pump feed pipe bolts.
  2. Remove the thermostat housing to water pump feed pipe.


46ebede.jpg

Fig. Remove the thermostat


Hope helps (remember rated this),

Jun 25, 2010 | 1996 Chevrolet Cavalier

1 Answer

Walk through on how to replace a thermostat in a 2001 Jeep grand Cherokee


Jennipherbrr,

1. Make sure the car is cold. Remove the radiator cap (press & turn about 1/4 turn to remove pressure in the system) Once the pressure is bled off you can remove cap and leave it rest on the filler opening.

2. Find the petcock on the radiator (the little valve attached to the radiator. You have to open/turn clockwise to drain the anti-freeze. Drain anti freeze below thermostat housing. About 1/2 to 1 gallon.

3. Have a catch basin for the anti freeze under the car. Remove upper radiator hose from radiator and thermostat housing.

4. Remove thermostat housing from engine block (usually two or three bolts in the thermostat housing). Scrap off ALL old gasket material from engine block. Double check and make sure all gasket material is removed from surface. If not the thermostat housing will leak.

5. Install new gasket with some high temp silicone. Place a couple of dabs on the thermostat housing and gasket (the silicone is used to keep the gasket in place) *MAKE SURE YOU INSTALL the thermostat the same way you took it out. Don't over tighten the thermostat housing bolts.

6. Remove the radiator cap and replace the anti freeze you removed (make sure the anti freeze is clean). Fill the radiator to the top of the filler neck and replace the radiator cap (push and turn the radiator cap to the right- like a pill bottle). Start the car and make sure the temperture guage goes up. The guage pointer should be in the middle of the guage.

7. Check the radiator reservoir for proper anti freeze level. DO NOT OPEN THE RADIATOR CAP WHEN THE CAR IS HOT!!! THE ANTI FREEZE IS HOT AND WILL BURN YOU.

Hope this helps

Apr 19, 2010 | 2001 Jeep Grand Cherokee

Not finding what you are looking for?
1990 Toyota Camry Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...