Question about 2004 Kia Sorento

Open Question

How do you remove the starter from a 2004 Kia sorento

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
aref_bilal
  • 13 Answers

SOURCE: I am changing the spark plugs on my 2004 Kia sorento

Be careful there.. If you remove the Throttle Position Sensor TPS or the throttle Cable, the engine light will come on because there is a certain setting that needs to be done to ensure accurate emission control.

Posted on Apr 14, 2009

Ad
  • 39 Answers

SOURCE: How do you change head lights on a 2004 kia sorento?

The whole headlight assembly needs to be removed from the vehicle to access the lamps inside; especially on the side with the battery (left side).

Remove 3 10m bolts (one on top two on front)

Headlight assembly is held in place wth a large Nylon clip ear outer edge at bottom of the unit. Tilt out at the top and then pull forward and upward to remove. It fels like something's gonna break, but it's pretty tough.

Remove large round cap from behind either high or low beam lamp. Both lamps are hels in with a metal spring clip. Low beam is H-7, high beam is H-3.

To re-install, press bar into Nylon clip and then install 3 10mm bolts. Use a Torx bit to engage gear teeth and adjust height if necessary. There may or may-not be adjusters for left-right alignment.

Posted on Jun 04, 2009

  • 972 Answers

SOURCE: 2004 kia sorento cannot get rear brake rotor off.

make sure parking brake is off
take off caliper
pemove rotor
if the park brake shoes inside rotor are tight then you have to loosen the adjuster to remove
theres a hole in the rotor rotate it up and look through hole until you see the adjuster wheel loosen by rotating adjuster with flat blade screw driver

Posted on Mar 25, 2010

alicantecoli
  • 22219 Answers

SOURCE: How to Remove the Ignition Switch From a 2003 kia

do you have the key?? if so then its relativly easy without teh key you will have to cut the whole lot off

Posted on Jun 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Oxygen sensor connector 2004 Kia Sorento


The removal procedure of Oxygen sensor connector for 2004 Kia Sorento is explained in below link. Please refer through it.

531fa0c2-d966-466f-8ade-159cb41e391a.jpg


0ebd0374-2764-42ba-a725-ed8fe7b650c7.jpg

Jun 11, 2013 | 2004 Kia Sorento

1 Answer

2004 kia sorento interior storage drawer under radio and above ashtray. I want to remove--someting stuck behind. Please tell me how to remove.


Both of the panels on ether side of the radio, with the vent in them, will pull straight out.
you can then access the screws to remove the radio ect.

Jul 18, 2011 | 2004 Kia Sorento

2 Answers

Where is the starter located on a 2006 kia sorento?


Thanks for choosing FixYa and welcome to the site. More then likely, it is on the side where you put gas in. This is an easy way to find it. Go to your gas cap area and crawl underneath the vehicle. Follow the gas lines that go down the side of the car. You should run into it that way. Your gas lines usually run on the edge of the car underneath. If you have any questions, feel free to ask. Thanks for using FixYa.

Apr 07, 2011 | 2004 Kia Sorento

1 Answer

How do I replace the radiator in my 2004 kia


I don't currently have access to step by step instructions for your Kia Sorento, but I would imagine that it takes a standard tool ratcheting tool set to unscrew the bolts for the shroud, and lift any fans out of the way. Then, the radiator hold down hardware can be removed and the radiator should be disconnected fromt he cooling system (via the hoses) and then you can pull it out. It does not weigh much.

Installation is the reverse of the removal.
---
recalls for engine follow:

Gasoline Engines
2004 KIA SORENTO


03/01/2009 KIA REMANUFACTURED ENGINE PROGRAM 01/01/2004 CYLINDER BLOCK DAMAGE - HEAD GASKET LEAK - POOR RUNNING OR HARD START, EXCESSIVE WHITE SMOKE AND/OR COOLANT SMELL FROM EXHAUST, MISFIRE DTC - REVISED 06/01/2005 LOCKNUT RE-USE PROHIBITED 07/30/2007 CRANKSHAFT PULLEY BOLT REPLACEMENT

Jul 21, 2010 | 2004 Kia Sorento

2 Answers

Does the kia sorento 2.5 crdi xe have a timing on a 2004 plate


THE KIA SORENTO HAS 3.3 AND 3.8 ENGINES THEY HAVE TIMING CHAINS.THE KIA 2.4 ENGINES HAS TIMING BELT GUIDE PLATE.

Jun 21, 2010 | 2004 Kia Sorento

2 Answers

2004 kia sorento cannot get rear brake rotor off. have removed screws and it is loose but wont come off.


make sure parking brake is off
take off caliper
pemove rotor
if the park brake shoes inside rotor are tight then you have to loosen the adjuster to remove
theres a hole in the rotor rotate it up and look through hole until you see the adjuster wheel loosen by rotating adjuster with flat blade screw driver

Mar 25, 2010 | 2005 Kia Sorento

Not finding what you are looking for?
2004 Kia Sorento Logo

Related Topics:

217 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76649 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...